Time Now Invisible Clock II Operation Instructions page 3

6. How to use the Custom Timer. First set a countdown time of from 3 seconds to 60 minutes. Then program up to 6
unique alerts to signal within this countdown time. The countdown time can be set to countdown once, to repeat over and over,
or to count-up after countdown completes. NOTE: If you set an alert at 10 minutes, it will signal when there are 10 minutes left
in the countdown; set an alert at 1 second to signal at the end of countdown.
STEP 1:
pm2:33
CUSTOM TMR
Program
Countdown
Time
Advance to
CUSTOM TMR
STEP 2:
pm2:33
Program up to
A : 00 : 00
6 alerts within
countdown
time
Advance to
Alert A
Alert A = 5 second vibration... or if alert switch (on the side of the unit) is set to beep = 1 beep
Alert B = 5 second vibration, 5 second space, 5 second vibration............or........... = 2 beeps
Alert C = 10 second vibration......................................................or.......... = 3 beeps
Alert D = 10 second vibration, 7 second space, 10 second vibration.........or......... = 4 beeps
Alert E = 20 second vibration......................................................or......... = 5 beeps
Alert F = 2 second vibration...................................................... or......... = 6 beeps
STEP 3: S
et
pm2:33
RPT : 20 : 00
to One
Countdown, to
Repeat, or to
Count-Up Press repeatedly until
RPT (repeat)
CTMR
pm2:33
Stop
C-UP : 20 : 00
Count-
down
Press two middle buttons
simultaneously for 1 second
or less to stop countdown
Restarting
pm2:33
Timer when
CUSTOM TMR
it is
programmed
Start here
Checking and changing programming (without erasing all programming)
T 08:00
8-13
pm2:33 pm2:33
CUSTOM TMR #A= 01:00
Press and hold for
Start here
3 seconds to see
alerts
NOTES for the Custom Timer:
1. During programming, once you have selected all the alerts you need, you can press Mode at any time to save your programming. To
start the timer, press Enter once, then Mode once.
2. Once the custom timer is programmed, it will remain programmed until all programming is erased.
3. To restart timer after countdown completes for one-time countdown or for count-up, press M to restart (at any time during count-up).
4. Set any alert to 1 second to have a signal at end of countdown.
5. From "CUSTOM TIMER" you can press Enter and wait until ready to start countdown by pressing Mode.
8-13 CTMR
pm2:33
TIME 00 :
00
Enter
adjustment
mode
CTMR CTMR
pm2:33
01
A : 00 :
Adjust seconds
CTMR CTMR
pm2:33
C-UP : 20 : 00
Count-Up
(after countdown
is complete)
This action
stops the timer
and puts it in
the ready
position to
start again
8-13 T 08:00
pm2:33
pm2:33
C-UP : 19 : 49
ADB
Press to enter
Press to start
T 08:00
pm2:33 pm2:33
#B= 01:00 #B= 01:00
Push
Press to scroll simultaneously
to allow this alert to
through existing
alerts be changed
CTMR
pm2:33 pm2:33
30
TIME: 00 : TIME :
Adjust seconds Advance to
minutes
CTMR
pm2:33 pm2:33
00 01
A : :01 A :
Adjust minutes
Advance to
minutes
STEP 4: S
CTMR
pm2:33
: 20 : 00
Countdown
(if timer doesn't
start, press Enter
then press Mode
One countdown
to start)
only (blank on left)
pm2:33
Restart
C-UP : 19 : 49
Then
count-
down
Press to restart
countdown
ERASE
CTMR
ALL
program-
ming
T 08:00 T 08:00
pm2:33
#B= 01:15
Press to
Advance to minutes
change
seconds
CTMR CTMR
pm2:33
00 40
:30 TIME : :30
Adjust minutes
(countdown time =
40 minutes & 30 seconds)
CTMR
CTMR
pm2:33
B : 00 : 00
: 01
Advance to
Alert B
TIP: To skip an
alert during
programming,
press the Enter
button two times
tart
CTMR
pm2:33
C-UP : 19 : 33
Press to save all
programming and start
countdown session
CTMR Exit
Mode
8-13
pm2:33
pm2:33
CUSTOM TMR ERASEALL=T
Hold for 3seconds
Start from here
T 08:00 T 08:00
pm2:33 pm2:33
#B= 01:15 #B= 03:15
Press to
change
minutes
Proceed to
STEP 2
below
Set Alert B the
same way as you
set A. You can
set one or all of
the alerts
A,B,C,D,E,F.
After setting the
alerts you want,
proceed to
STEP 3 below
NOTE: You can
press Mode after
setting 1, 2, or more
Alerts; then to start
the timer, press
Enter once, and
Mode once.
8-13
pm2:33
CUSTOM TMR
Press two middle
buttons simultaneously
and hold for 2
seconds to exit mode
CTMR CTMR
pm2:33
ERASED ALL
Press to erase
T 08:00
pm2:33
#B= 03:15
Press to accept
changes. Press
again to exit mode