Time Now Invisible Clock II Operation Instructions page 2

4. How to use the Timer.
8-13 TIMER
pm2:33 pm2:33
TIMER SET 00 : 00 : 00
Advance to Enter Timer
Timer Set mode
How to
TIMER
pm2:33
set the
R
00 : 10 : 30
Timer to
Repeat
over &
R
Press until
over.
appears in screen
How to
TIMER
pm2:33
ERASE a
01 : 10 : 13
countdown
time and
program a
To erase during a
new one
countdown, press
simultaneously
NOTE: The Timer saves the last programmed time. When countdown is complete, this time is displayed. To use this time again, press Mode
to start the timer with this time. If you wish to use this time again but have gone to another mode, go to TIMER SET via the Mode button, press
Enter once and press Mode to start this countdown time (you can wait as long as you wish to press Mode to start the Countdown).
5. How to set Alarms.
button down for 3 seconds to enter the Alarms mode - see instructions below on how to do this.
8-13
pm2:53
AM -:--
pm2:53
ALARMS SET
ALM01-SET
Advance to Hold for 3
seconds to enter
ALARMS SET
mode
TIP 1:
To set multiple alarms or to check your set alarms, use the Enter button to scroll through set
alarms. To set additional alarms go to a blank setting, then continue as in drawing #3 above.
TIP 2
: Vibration alert = 20 seconds. Press any button to stop alert. If you press the Lite button, it
stops the alert and engages the snooze feature - see Note 3 below about the snooze button.
Note 1.
A set alarm will signal in all other modes unless alarm switch (on side of unit) is set to O (off). An alarm
remains set after its time has passed, and will sound again every successive day until it is erased.
Note 2.
Set alarms are automatically organized in the order of next to go off, according to the time of day. In other
words, when you check your set alarms, ALARM 01 will be the next to signal, then ALARM 02...etc.
Note 3.
SNOOZE button - When an alarm signals, press the light button to turn off the alarm and engage the
snooze feature; the alarm turns back on automatically after 5 minutes. You can only do this once with each alarm.
Erasing an Alarm
: To erase an existing alarm, (a) use the Mode button to advance to "ALARMS SET"; (b) use the Enter button to
select the number of the alarm that you wish to erase; (c) Press both the Enter and Set buttons simultaneously. This will erase the
alarm's time, and therefore will erase the alarm itself.
Changing the Time of an Existing Alarm
"ALARMS SET"; (b) Use the Enter button to select the number of the alarm that you wish to modify; (c) Use the Set button to change
the minutes, then press the Enter button to shift to the hours, which you may change with the Set button; (d) Press the Mode button to
accept the change.
The Timer can be set to countdown once, or set to repeat over and over.
TIMER
pm2:33 pm2:33
30
00 : 00 : 00 :
Advance to
Select Seconds
minutes
(press "Enter" to
skip seconds)
First set the countdown time
as shown in the above steps,
then before starting the timer,
press the "Enter" button until
R appears in the left of the
display, then press Mode
button to start the timer.
TIMER
pm2:33
Then to program in a
00 : 00 : 00
new countdown time
proceed as shown
starting with the 3rd
drawing in the very
Press to erase
countdown time first line at the top of
this page
Up to 12 Alarms may be set. NOTE: The Alarm auto-protect feature requires that you hold the Enter
Time now Alarm time being set
30
AM -:
pm2:53 pm2:53
ALM01-SET ALM01-SET
Adjust minutes
Advance to hours
(Note: AM/PM)
: To change the time of an existing alarm, (a) use the Mode button to advance to
TIMER TIMER
pm2:33
00 10
: 30 00 : : 30
Select minutes
To EXIT during a countdown
TIMER
pm2:33
01 : 10 : 13
Press simultaneously
until display blinks
pm2:33
TIMER SET
To erase countdown
time when countdown
is not running, advance
to Timer Set.
Alarm number
0 7
AM :30
AM :30
pm2:53
ALM01-SET
Adjust hours
(Note: AM/PM)
TIMER TIMER
pm2:33 pm2:33
00 01
: 10 : 30 : 10 : 30
Advance to Select hours
hours
8-13
pm2:33
TIMER SET
Exit
8-13 TIMER
pm2:33
01 : 10 : 13
Enter Timer
mode
7:30 AM -:--
AM pm2:53
pm2:53
ALM02-SET
ALM01-SET
Set this alarm
Advance to set
another alarm (to
Exit press Mode)
Hours Minutes Seconds
TIMER
pm2:33
01 : 10 : 29
Start countdown;
Countdown time in this
example =1hour, 10
minutes, 30 seconds.
When countdown = 0,
alarm vibrates or beeps
NOTE: Vibration
alert lasts for 20
seconds. Press any
button to turn off
vibration or beep.
TIMER
pm2:33
00 : 00 : 00
Press to erase.
Continue as in
step 3 in this
line. Finish by
setting the
alarm with the
mode button
To Erase an
Alarm: Go to the
Alarm you want to
erase, then press
Enter & Set
simultaneously; to
exit press Mode.