Mitsubishi LVP-X80U User Manual page 33

ITEM
MENU POSITION
EXPAND MODE
FRAME POSITION
AUDIO MODE
VIDEO SIGNAL
ANAMORPHIC
LANGUAGE
RESET ALL
MEMORY CALL
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
HORIZ. PIXELS
VERT LINES
PLL
VERT.SYNC
SHUTTER (U)
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS)
MUTE
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII '+' '–'
HEX 2Bh 2Dh
[Example 1] Set the AUTO POWER ON to ON.
Sending commands
from the PC etc.
30 30 41 50 4F 4E 30 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and
the difference data of B from G.
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands
from the PC etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands
from the PC etc.
30 30 53 0D
'0' '0' 'S' ' '
ASCII HEX
MP 4Dh 50h
EX 45h 58h
FM 46h 4Dh
AU 41h 55h
VS 56h 53h
SC 53h 43h
LG 4Ch 47h
RSTALL 52h 53h 54h 41h 4Ch 4Ch
MMC 4Dh 4Dh
HP 48h 50h
VP 56h 50h
FN 46h 4Eh
TRK 54h 52h
CIN 67h 49h
HLD 48h 4Ch
HLB 48h 4Ch
HLE 48h 4Ch
CLP 43h 4Ch
CLW 43h 4Ch
HPL 48h 50h
VLN 56h 4Ch
PLL 50h 4Ch
VSC 56h 53h
SHU 53h 48h
SHL 53h 48h
SHLS 53h 48h
SHRS 53h 48h
MUTE 4Dh 55h
'0' '1' '2' '3'
30h 31h 32h 33h
'
30 30 41 50 4F 4E 30 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
VALUE
0 (Upper left), 1 (Lower right)
1 - 4
1 - 5
1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO)
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
0 (OFF), 1 (ON)
0 ( ), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 (
43h 0 (AUTO), 1 (USER1), 2 (USER2)
+ (increase), – (decrease)
+ (increase), – (decrease)
00 - 39
4Bh + (increase), – (decrease)
4Eh 0 (RGB), 1 (YC
44h 0 (AUTO), 1 (ON), 2 (OFF)
42h –01 - –99
45h 01 - 99
50h 00 - 63
57h 01 - 63
4Ch 0000 - 9999
4Eh 0000 - 9999
4Ch 0 (AUTO), 1 (0), 2 (1), 3 (2), 4 (3), 5 (4), 6 (5), 7 (6), 8 (7)
43h 0 (AUTO), 1 (ON), 2 (OFF)
55h 000 - 383
4Ch 000 - 383
4Ch 53h 000 - 510
52h 53h 000 - 510
54h 45h 0 (MUTE OFF), 1 (MUTE ON)
'4' '5' '6' '7'
34h 35h 36h 37h
Status code from
projector
'
Status code from
projector
Status code from
projector
'
4
)
C /YP P )
B R B R
'8' '9'
38h 39h
Meaning
Command for setting the
AUTO POWER ON to ON
Command received
(Command echo back)
Meaning
Command for setting the
picture control
Command received
' (Command echo back)
Meaning
Command to confirm
setting of TINT
Command (setting of TINT
is +10) carried out