User Memory For Signal Setting - Mitsubishi LVP-X80U User Manual

Mitsubishi user manual lcd projector lvp-x80u
Hide thumbs Also See for LVP-X80U:
Table of Contents

Advertisement

4 SIGNAL
MEMORY CALL ........ Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION .... Use to adjust the horizontal position of the image.
VERT. POSITION ..... Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT .... The unit adjusts itself automatically when connected to a
DVD player with a component video output (Y, C
the case ( Y, P
equipment that includes RGB output terminal, adjust to
RGB mode.
HOLD .................. Adjusts the image when flagging occurs near the top of the
screen.
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image. The image size grows
wider as the number increases. (Adjust to the horizontal
pixels of the input signal for normal setting.)
VERT.LINES ...... Use to adjust the height of the image. The image size grows
higher as the number increases. (Adjust to the vertical
lines of the input signal for normal setting.)
PLL ...................... Use to adjust the image when skewed on top. Select AUTO
for normal setting.
VERT.SYNC. ...... Use to adjust the image when its motion does not run
smoothly. Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.

User memory for signal setting

This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1. Select MEMORIZE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).
3. Press the ENTER button.
Initialite the setting which has been changed (Default)
Select RESET in the SIGNAL menu, and press the ENTER button.
When initializing, selection buttons will not work for about 2 - 18 seconds.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1. Select DELETE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3. Press the ENTER button.
The recorded setting will be reset.
P
). In the case the projector is connected to
B,
R
Opt
SIGNAL
MEMORY CALL
A
U
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
C
). In
B,
R
COMPUTER INPUT
R G B
R G B
HOLD
USER
MEMORIZE
SIGNAL-USER
CLAMP POSITION
CLAMP WIDTH
HORIZ. PIXELS
VERT. LINES
PLL
VERT. SYNC.
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
SHUTTER(RS)
XGA60
AUTO
0
0
0
0
RGB
AUTO
DELETE DEFAULT
0
0
0
0
AUTO
AUTO
0
0
0
0
EN – 17

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Lvp-x80

Table of Contents