Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Octava HD70STP-EX
Summary of Contents for Octava HD70STP-EX
- Page 1 HD70STP-EX Installation Guide...
-
Page 2: Table Of Contents
Contents Description ..............3 Features ................. 4 Application Diagram ............4 Front and Back Panel ............. 5 Installation............... 6 Ethernet cable installation recommendations ....7 IR Configuration .............. 8 IR Emitter ................ 9 LED Indicator ..............9 Serial Data(RS232) ............10 Mounting Tabs .............. -
Page 3: Description
Description The HD70STPEX HDMI extender simplifies HD video connectivity using 1 CAT6 cable. The HD70STP is a multi-format extender that extends 1080p, 4x2k ultra HD, 3D video and Advanced bitstream multichannel audio formats 200ft on 1 single CAT 6 cable.. The HD70STPEX also extends IR, RS-232 controls and PoE power thus simplifying installations while delivering high quality uncompressed 1080P HD video and audio... -
Page 4: Application Diagram
Application Diagram... -
Page 5: Front And Back Panel
Front and Back Panel 3. CAT6 8. LED indicator 4. IR RX Port 5. IR TX Port 6. Power In 1.HDMI In 7. RS-232 port 2.HDMI Out HD70STP-TX HD70STP-RX HDMI In connect to video source HDMI Out connect to display CAT6 Link TX unit with RX unit IR RX... -
Page 6: Installation
Installation HD70STP-TX(transmitter) HD70STP-RX(receiver) Installation Procedure Connect “CAT6” of the Transmitter and Receiver with CAT6 cable. (see page 7 for cable recommendations.) Connect HD source to HDMI In of Transmitter unit Connect Display to HDMI out of Receiver unit IR connection(optional)-configure and connect as shown in section: “... -
Page 7: Ethernet Cable Installation Recommendations
Note 2- Unshielded CAT5e and CAT6 cables can be used with your Octava system though they may result in limiting the maximum attainable distance depending on quality of cable. Cable Type Note CAT7 cable is recommended. -
Page 8: Ir Configuration
I.R. can be sent in 2 directions: 1) from Receiver to Transmitter or 2) from Transmitter to Receiver unit. For proper operation, it is recommended that only Octava supplied I.R. emitter and receiver cables be used. Configuration 1: Sending IR from Receiver to Transmitter Unit... -
Page 9: Ir Emitter
IR Emitter An IR Emitter cable has been included with your Octava Product. The IR emitter cable enables you to control your source using I.R. remote control. Locate the IR receiver on the video source. Note, you may need to refer to your source data sheet. -
Page 10: Serial Data(Rs232)
Serial Data (RS-232) Serial control data can be sent using the RS-232 ports from Transmitter to Receiver unit for controlling the attached display. A 3 pin Phoenix connector is provided to connect with a RS-232 serial cable. Prepare your serial cable according to diagram below The following shows the cable configuration for sending serial commands from the TX to the RX ( display side). -
Page 11: Mounting Tabs
Mounting Tabs The HD70STP includes removable wall mounting tabs. The wall mounting tabs can be removed if not needed wall mounting tabs installed Wall mounting tabs can be removed if not needed. -
Page 12: Warranty
If Octava's equipment fails because of defects (1) year from the date of receipt, Octava will at its option, A) repair or replace the equipment, or B) request return of equipment for refund of the price paid for the product provided that the equipment has not been subjected to mechanical, electrical or other abuse or modifications. -
Page 13: Specifications
Bi -Directional IR. Send IR from display side to source side OR vice versa. Infrared Frequency Wideband IR 20-60 KHz circuitry for maximum IR remote compatibility using Octava supplied IR cables. Serial Port ( RS-232) RS-232 extension for controlling display device. Ethernet Cable...