1. Manuals
  2. Brands
  3. Ernex AS Manuals
  4. Saw
  5. Norsaw 250
  6. Manual

Ernex AS Norsaw 250 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
�����������
��
��������
����������������������������������������
�������������������������������������������
����������������������
������������

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Norsaw 250 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ernex AS Norsaw 250

Summary of Contents for Ernex AS Norsaw 250

  • Page 1 ����������� �� �������� ���������������������������������������� ������������������������������������������� ���������������������� ������������...

  • Page 2: Table Of Contents

    CONTENTS Side 1. Safety instructions 2. General instructions/Dust and Noise 3. Mounting/Power Supply/Transport 4. Functions 5. Operation 6. Maintenance/Repair 7. Troubleshooting 8. Warranty 9. Technical data 10. Standard/Optional equipment 11. Spare part lists/Drawings 12. Wiring diagram 13. Product Marks 14. Conformity declaration Original manual: Norwegian 525053...

  • Page 3: Safety Instructions

    1. SAFETY INSTRUCTIONS The European Union Machinery Directive 2006/42/EF, 2006/95/EF and EN 1870-5:2, requires manufacturers, importers, suppliers and dealers to ensure that machines are designed and built to avoid causing injury to users and others by accident or inappropri- ate work posture or strain. Machinery used at a workplace must - wherever practicable - be secured and pose no risk to operator health during installation, operation, cleaning or mainte- nance.

  • Page 4: General Instructions/Dust And Noise

    2. GENERAL INSTRUCTIONS/DUST AND NOISE 2.1 General safety precautions: • IMPORTANT! According to the CE-regulations an extension table should be used wherever possible. • IMPORTANT! Note that the saw blade moves up and forward the entire length of the slot. •...
  • Page 5 2.3 Dust and Noise • Dust and noise measurements have been performed for work with the materials and saw blades for which the machine is intended (see section 1 Safety Instructions). Measurement uncertainty is related to local conditions and can vary with the saw blade/ transmission characteristics.

  • Page 6: Mounting/Power Supply/Transport

    3. MOUNTING/POWER SUPPLY/TRANSPORT 3.1 Mounting the saw The saw is delivered in a carton box with the table top downwards Fig. 1. Fig. 1 Pull out/Unfold the legs Fig. 2 and tighten the locking wheels Fig. 3. Fig. 3 Fig. 2 For best stability place saw on a level, even surface.

  • Page 7: 3.2 Mount The Push Sticks

    Mount the top guard by pushing the tube to the bottom and make sure that the handle A is locked into position Fig. 5. Fig. 5 Check saw blade and riving knife and assemble according to illustration Fig. 6. Fig. 6 Mount the fence by loosening the handle A and lead the nut underneath the fence into the slot of the aluminium profile.
  • Page 8 3.3 Mounting the tables The same table can be used on both sides of the saw. Length: 1 m - Weight: 3 kg...
  • Page 9 3.3 Connecting main supply Use an approved extension cord with ground protection/earth wire diam. 2,5 mm², max. length 25 m. Tilt the switch and connect power supply cable. NB! The switch should always stay in this position when the saw is in use Fig. 9. Fig.

  • Page 10: Functions

    Fig. 11 Fig. 12 4. FUNCTIONS 4.1 On/off switch On the front side of the saw there is a green ON- and a red STOP button. The switch has an overload protection and a low-volt cut out which will automatically stop the motor. If the overload protection comes into operation, wait until the motor cools down and restart.
  • Page 11 4.3 Pushing/pulling of saw blade The blade can be pushed or pulled along the slot in the turntable Fig. 15 and 16. The slide mechanism can be locked with the locking wheel G below the table top Fig. 14. Fig. 15 Fig.

  • Page 12: Operation

    5. OPERATION 5.1 Cross cutting Set the desired cutting angle - Section 4.4. and 4.5. Adjust the position of the fence and lock with locking handle J Fig. 19. Set the upper guard U approx. 5 mm above the height of material. Lift and (gently) push the blade if you need to increase the cutting width/length.

  • Page 13: Cutting Grooves

    Start the motor and feed the material through the blade along the fence Fig. 22. Use push sticks when the distance between fence and saw blade is < 120 mm. The riving knife is always to be used when ripping. Make sure that it is correctly fitted and adjusted see Fig.

  • Page 14: Maintenance/Repair

    6. MAINTENANCE/REPAIR CAUTION! MAKE SURE POWER SUPPLY IS DISCONNECTED WHILE PERFORMING MAINTENANCE OPERATIONS. A minimum of maintenance is required to ensure satisfactory performance and a long service life. • Lubricate moving parts at regular intervals. • Check all screws and nuts regularly for tightness. •...
  • Page 15 6.2 Replacing and adjusting riving knife • Pull the plug and lower the blade cover as in Section 6.1. • Loosen the screws and nut Fig. 27 and remove or reposition the riving knife (by replacing riving knife). • The riving knife is mounted using same method in reverse. The thickness of the riving knife should be the nearest thickness but slightly less than the kerf width of the saw blade.

  • Page 16: Troubleshooting

    6.5 Repair Routines at repair: * The machine must only be repaired by qualified electricians or authorised service workshops. Testing the brakes: * The brake for the saw blade rotation should be tested regularly. The stop-time must be max. 10 sec. Start/stop the saw 10 times in a row and check the stop- time.

  • Page 17: Warranty

    3 years, except for electrical parts which still has a 1-year warranty commencing from the date on which the machine is sold to the end user. Ernex AS/The importer prom- ise to repair, or at our option, replace with like grade and quality any product determined to be faulty due to the failure of parts, material or workmanship.

  • Page 18: Technical Data

    9. TECHNICAL DATA Gjerde ® Manufacturer: Ernex AS, Norway. Model: Norsaw 250. Table size: 670 mm x 565 mm. Height: 860 mm. Transport height: 430 mm. Weight: 37 kg. Saw blade: Carbide tipped, Z=40 Diam. 250 mm. Bore diam. 30 mm.

  • Page 19: Spare Part Lists/Drawings

    Ernex AS Spare Part List Gjerde 250 Pos. Art.No. Text 725 179 Sawtable top 725 020 Carrying handle 725 178 Turntable w/scale 725 120 Pre-stop plate compl. 725 019 Riving knife 2.5mm w/clamp 725 065 Hinge plate compl. 725 216 Bracket f/riving knife compl.
  • Page 21 2011...
  • Page 22 Ernex AS Spare Part List Tables 250 Pos. Art.No. Text 725 048 Frame f/alu. table 725 155 Locking handle M8x15 725 232 Leg, alu. table compl. 725 233 Foot compl. (1 pc. adj.) 725 209 Locking wheel 725 260 Length stop f/alu. table...

  • Page 24: Product Marks

    13. PRODUCT MARKS...

  • Page 25: Conformity Declaration

    Gjerde 250 SAMSVARSERKLÆRING CONFORMITY DECLARATION KONFORMITÄTSERKLÄRUNG KONFORMITETSINTYG DICHIARAZIONE DI CONFOMITA Ernex AS Fabrikant – Manufacturer – Hersteller – Produttore: 1792 Tistedal Adresse – Adress – Anschrift – Indirizzo: Erklærer herved at : Mod.: Gjerde 250 Nr.: ………………… Maskin: Som er omfattet av denne erklæring, er fremstilt i overensstemmelse med Rådets direktiv 2006/42/EF, 2005/95/EF og EN 1870-5:2002.
  • Page 26 Holland/Netherland: Gjerde B.V. Mors 9, NL-7151 MX Eibergen Tel: +31 545 472855, Fax: +31 545 472865 E-mail: info@gjerde.nl www.gjerde.nl Ernex AS 2011 Bjørnstadgt. 7, N-1792 Tistedal, Manufacturer: Tel.: +47 69178330 - Fax +47 69178360 E-Mail: ernex@ernex.no - www.ernex.no...

Table of Contents