Advantech SIU7117 User Manual

3m ip camera: bullet + wdr + poe

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

3M IP Camera: Bullet + WDR + PoE

User Manual

Release: 12 May 2014

Table of Contents

Summary of Contents for Advantech SIU7117

Page 1: User Manual
3M IP Camera: Bullet + WDR + PoE User Manual Release: 12 May 2014...
Page 2: Table Of Contents
CONTENTS - Chapter I Introduction ....................3 1.1 Highlights of your new Network IP Camera ..............3 1.2 Safety Instructions ......................4 1.3 Packaging Contents ......................5 1.4 Familiar with your new Network IP Camera ..............6 1.5 DI/DO PIN ASSIGNMENT ....................8 1.6 Installation of the Network IP Camera ................
Page 3 3-7 Motion ........................... 44 3-8 PTZ Control ........................46 3-9 Event ..........................48 3-9-1 Settings ........................49 3-9-2 Media ........................51 3-9-3 Event Server ......................52 3-10 Recording ........................56 3-11 SDHC ..........................57 3-12 Log ..........................59 3-13 Device Info ........................60 3-14 Maintenance .......................
Page 4: Chapter I Introduction
Chapter I Introduction 1.1 Highlights of your new Network IP Camera Congratulates on purchasing this high-resolution 5Mega pixels network IP Camera! This IP Camera provides 5Mega pixels high-resolution video quality, with the advanced megapixel lens, you can view images remotely in more detail than conventional close-circuit cameras.
Page 5: Safety Instructions
1.2 Safety Instructions Please follow the safety instructions listed below when you’re using this Network IP Camera, or you would harm this camera and / or yourself! Also, the warranty will become void if you disobey these safety instructions. This Network IP Camera is sophisticated electronic device; do not drop it from high places.
Page 6: Packaging Contents
1.3 Packaging Contents Please check the contents of your new Network IP Camera when you unpack the package. If any item is missing, please contact your dealer of purchase for help. Item No. Description Quantity Network IP Camera Bracket Kit Sun Shield Kit CDROM Quick Installation Guide...
Page 7: Familiar With Your New Network Ip Camera
1.4 Familiar with your new Network IP Camera Item Description 1. IP camera device IP camera 2. I/O cable RS485-+ , DI/DO , GND , DC12Volt/2A input Reset Button , Audio output , Audio input Network, RJ45 connector TV output, BNC connector [Front site] Item Description...
Page 8 [Back] Item Description 1. Screw Connects between camera device body & sun shield. 2. Sun Shield Protect camera device body from sun shine or rain directly 3. Camera device IP camera metal case body 4. Bracket mount The portion to mount bracket 5.
Page 9: Di/Do Pin Assignment
1.5 DI/DO PIN ASSIGNMENT Item Description - : RS485- + : RS485+ 1 : DO 2 : GND 3 DI DC12 Volt/2A input Reset Button Audio output Audio input Network, RJ45 connector, two LED index, orange color is power index, green is network index TV output, BNC connector ※Please check the I/O cable attached index before insert or release any wire.
Page 10: Installation Of The Network Ip Camera
1.6 Installation of the Network IP Camera Please follow the instructions below to setup your new IP camera. 1. Connect Ethernet cable to LAN port. 2. Plug DC power adapter to power outlet on the wall. 3. Connect DC power cable to IP Camera’s DC power connector. 4.
Page 11 6. Secure the wall mounting metal bracket on the wall then secure the bullet camera on the bracket. 7. Repower on the camera and refer to the following procedures to access and configure it. 8. If this IP Bullet camera is connected to a PoE switch then the device can be powered on without use the power adapter.
Page 12: Chapter Ii Access Network Ip Camera By Web Ui
Chapter II Access Network IP Camera by Web UI 2.1 Locate the IP address of Network IP Camera You can use your new Network IP Camera by its web user interface via web browser. Currently the viewing system requirement for Network IP camera is: ˙OS: Microsoft Windows XP / Vista / WIn7 / Win8 ˙Browser: IE8 / IE9 / IE10 32bit...
Page 13 Press ‘Discover’ button to search for all IP Cameras on your local network (make sure all IP Cameras are powered on and connect to local network first). When you find any IP Camera, you can click on it and click ‘Link’ button to connect to it by your web browser.
Page 14: Access To Ip Camera's Web User Interface And Install Activex Plugin
2.2 Access to IP Camera’s Web User Interface and Install ActiveX Plugin When you know the IP address of IP Camera, you can connect to it by Internet Explorer web browser by entering its IP address in address bar. The use login screen will appear when you get connected: IP Camera’s administrator username and password are both ‘admin’...
Page 15 For IE 9 or above version: Click ‘Install’ button located at the bottom of IE to install ActiveX plugin. If you’re prompted that: ‘Windows Firewall has blocked some features of this program’...
Page 16 Click ‘Allow access’, or IP Camera will not be able to function properly. When you’re installing Internet Explorer plugin, you may also be prompted that if you want to allow changes to be made to your computer: Click ‘Yes’ to allow changes. After ActiveX plugin is installed, you should be able to see the video stream from camera.
Page 17: Viewing Live Video
2.3 Viewing Live Video After ActiveX control is installed, you can view IP camera’s video by web browser. Just connect to IP camera by web browser and login, then you can see live video from IP camera: There are various controls on web page, here are descriptions of every control item: Item Description...
Page 18 size. If your computer monitor’s resolution is not enough and you want to see full image view, switch to fit screen and image size will adjust automatically. ‘Connect’ Start live video view. button ‘Disconnect’ Stop live video view. button ‘Snapshot’ Take a snapshot or camera video and save image file button on your computer.
Page 19 ‘Enable Digital This function will enlarge video view digitally from Zoom’ button 1X to 10X. Move the bar up to see objects in screen in detail. The blue square in the small screen at the left top side high lights the zoom in range. Please note: that digital zoom uses computer algorithm to enlarge the video and some details may lost.
Page 20: Client Settings
2.4 Client Settings In ‘Client Settings’ menu, you configure basic IP camera settings like data transfer protocol and data storage folder. To access ‘Client Settings’ menu, click ‘Client Settings’ button on the left. The following screen will appear:...
Page 21: Chapter Iii Advanced Configuration
Here are the descriptions of every setup item: Item Description RTSP/RTP over TCP Select this option to use RTSP (Real-Time Streaming Protocol) to transfer video data over TCP. RTSP/RTP over UDP Select this option to use RTSP (Real-Time Streaming Protocol) to transfer video data over UDP.
Page 22: System
To access configuration menu, click ‘Configuration’ button on the left. The ‘Configuration’ submenu will appear, please pick a setup item you wish to configure. 3-1 System In this menu, you can configure basic IP camera settings like hostname and time.
Page 23 Here are the descriptions of every setup item: Item Description Host Name Input the IP camera’s hostname here, it can be any meaningful words or characters that will help you to identify this IP camera. You can use IP camera’s installation location as host name, and this will help you to identify IP camera when you have many IP cameras installed.
Page 24: Security
time correct. Keep the current Select this option and date / time setting will not date and time be changed when you click ‘Apply’ in the page. You can check ‘Camera Date and Time’ item in this page to know IP camera’s current date and time setting.
Page 25 camera setting) - User (Can view IP camera’s video and see log only) - Guest (Can view IP camera’s video only) There can be multiple users, but only one administrator is allowed, and you can’t change administrator’s user name (it will always be ‘administrator’).
Page 26 password! Or you’ll need to reset IP camera’s all settings to get administrator’s password recovered. Account List Here lists all users existed in IP camera. If you want to remove one user, click it in the list, and then click ‘Remove’ button. If no user is existed, ‘New Account’...
Page 27: Network
3-3 Network In this menu, you can configure IP camera’s network setting. 3-3-1 ‘General’ setup page Setup IP address for this IP camera. This IP camera supports both IPv4 and IPv6 IP address. Here are the descriptions of every setup item: Item Description Select this option to assign an IP address to LAN port...
Page 28 on LAN automatically. DHCP IPv4 / IPv6: Obtain both IPv4 and IPv6 address from DHCP server on LAN automatically. Static IPv4 / IPv6: Assign an IPv4 / IPv6 address to IP camera manually. If you don’t have a DHCP server on your local area network, you must use this option to specify an IP address.
Page 29 PPPoE Select this option to use PPPoE to connect to network. You have to input PPPoE username and password assigned by network operator to get connected. HTTP Port Input IP camera’s web connection port number here. When this port number is changed, you need to change web browser’s port number you used to connect to IP camera.
Page 30: Advanced' Setup Page
3-3-2 ‘Advanced’ setup page You can setup advanced network settings in this page. This page is intended for advanced settings only, and this IP camera will work fine even you don’t make any changes to this page. Here are the descriptions of every setup item: Item Description Multicast...
Page 31 here. Multicast RCTP audio port: Input port number for RCTP audio here. Multicast TTL: Input TTL value for multicast here. Bonjour If you’re using Mac OS and you have Bonjour installed, you can use it to discover this IP camera. Enable QoS to improve the data transfer priority of this IP camera (Your local area network must support QoS).
Page 32 HTTPS Check ‘Enable HTTPS’ box to enable HTTPS channel to encrypt transferred data. You can also define HTTPS port number in ‘HTTPS Port’ field if you don’t want to use default value ‘443’. When you finish, click ‘Apply’ to save changes.
Page 33: Ip Filter
3-4 IP Filter When this IP camera is directly connected to Internet and not protected by firewall, this function acts like a mini built-in firewall to protect the safety of this IP camera and avoid attacks from hackers. Here are the descriptions of every setup item: Item Description Enable Filter...
Page 34 camera will only accept connections established from these IP address. If you want to specify one IP address only, input the same IP address in both field. Click ‘New’ button to add IP address into accepted IP list. Deny IP list Here lists all IP address that cannot build connections to this IP camera.
Page 35: Video
3-5 Video You can adjust the image of the IP camera in this menu. There are 3 sub-menus in this menu: Image Setting, Video Setting, and Overlay, which can be accessed by tabs on the top:...
Page 36: Image Setting
3-5-1 Image Setting You can adjust the image parameters in this page. Here are the descriptions of every setup item: Item Description Brightness / Control the image parameters. Click ‘ - ' to decrease Contrast / value, or click ‘ + ‘ to increase value. You can also input Saturation / the value in the field directly.
Page 37 Set up the values of exposure value, exposure time and gain to create a profile and click “Apply” to enable it. Item Description Mirror Check ‘Vertical’ or ‘Horizontal’ box to flip the image vertically or horizontally, this will help to correct the orientation of image when IP camera is hanged bottom-up by camera holder.
Page 38 sunlight. You can select the behavior or IR-Cut filter: - Auto: IR filter will act automatically. If you don’t know if you should use IR filter, select this option. - Always ON: IR filter is always on. - Always OFF: IR filter is always off. IR-Cut filter will only be switched on when there’s sunlight.
Page 39: Video Setting
3-5-2 Video Setting You can adjust the video transfer parameters in this page. Here are the descriptions of every setup item: Item Description H.264 Select the compression of main stream: H.264 / MPEG4. /MPEG4 Video Select video resolution. Resolution - H.264: 2048x1536 (QXGA) / 1920x1080 (1080p) 1280x960 (960p) / 1280x720 (720p) 720x480 (D1)
Page 40 Please note that some video resolution is not available when video encoder is ‘MPEG4’. When network speed is insufficient, select a lower video resolution will help. Frame Rate Select video frame rate. Please note that some frame rate is not available when video encoder is ‘H.264’. When network speed is insufficient, select a lower frame rate will help.
Page 42: Overlay Setting
3-5-3 Overlay Setting You can adjust the video overlay parameters in this page. Here are the descriptions of every setup item: Item Description Enable Time Check this box to enable overlaying time stamp on Stamp video. Remove the Check this box to remove time stamp’s background color background color.
Page 43 Enable Image Check this box to overlay a specific image on Overlay video, so you can show certain text / picture on the video and help people to identify this IP camera. Click ‘Browse’ button to pick a picture on your computer, then click ‘Update’...
Page 44: Audio
3-6 Audio You can adjust audio input / output parameters here. Here are the descriptions of every setup item: Item Description Enable Check this box to enable microphone. If you don’t Microphone want to hear voice from IP camera, you can uncheck this box to disable it.
Page 45: Motion
3-7 Motion This IP camera is capable to detect object’s motion, so IP camera will only record when there’s motion and save disk storage space. Motion detection is performed by examine the movement of objects in rectangular motion detection area. You can define up to 3 motion detection areas.
Page 46 - Move: Use the mouse to drag the title text. - Resize: Use the mouse the drag the four corners (upper-left/right, lower-left/right) to resize it. If you only want to adjust width or height, drag the four sidebars (top, bottom, left, and right).
Page 47: Ptz Control
3-8 PTZ Control If you mount the IP camera on pan-tilt camera cradles that support pan-tilt control via RS-485 connection, you can use this function to control pan-tilt camera cradle so you can control the orientation of IP camera from remote place. Here are the descriptions of every setup item: Item Description...
Page 48 Please refer to pan-tilt camera cradle’s user manual to define the protocol. Port Setting - Baud Rate: Select data baud rate of RS-485 interface that pan-tilt camera cradle will accept. When the length of RS-485 connection is very long (longer than 200M), it’s not recommended to use high speed connection (greater than 2400bps).
Page 49: Event
3-9 Event When there’s an event, you can use this setup page to define what IP camera should do, like send an Email or trigger digital output to activate external alarm. There are three setup pages: 1. Setting: Define a new event and manage events. 2.
Page 50: Settings
3-9-1 Settings This page lists all existing events. You can click ‘Modify’ button to edit an existing event, or ‘Remove’ to delete an existing event. To create a new even, just click “New” button to add an Event setting.
Page 51 To add a new event, click ‘New’ button and the descriptions of every setup item is listed below: Item Description Enable Setting Check this box to enable this event. If you just want to disable this event temporarily, you can uncheck this box to keep this event and disabling while not deleting it.
Page 52: Media
3-9-2 Media You can define what kind of media file should be saved on designated media. Here are the descriptions of every setup item: Item Description One Snapshot Save a picture file when event is triggered. Maximum Save a video clip. You can also select the recording Video File Size length before and / or after the time when event is triggered in ‘Pre Event’...
Page 53: Event Server
3-9-3 Event Server You can define the details of remote media server: FTP (File), SMTP (Email), and Samba (File). A Samba server can be any computer running windows operating system with network neighbor function enabled. Many stand-alone network file server also support samba server function. Here are the descriptions of every setup item: Item Description...
Page 54 - Port: Input FTP server’s port number. In most cases it should be default value ‘21’. - User Name: Input FTP server’s username. - Password: Input FTP server’s password. - File Path Name: Input the path where you want to save file on FTP server, like ‘upload/record’.
Page 55 address to ‘White List’ in your anti-spam software) - Receiver #1 Email Address: Input primary recipient’s Email address. This field is required. - Receiver #2 Email Address: Input backup recipient’s Email address. This field is optional. - Subject: Input Email title that will appear in the Email send by IP camera.
Page 56 - Password: Input Samba server’s password. - Test SMB: Click this button to test Samba server settings above immediately. Tips: Some samba server does not have username and password check, you can just input samba server address and path to access the file storage space. When you finish with above settings, click ‘Apply’...
Page 57: Recording
3-10 Recording When a SD card is inserted into IP camera, you can save video files on it. Note: Be sure that the SD Card format should be FAT32. The NTFS format cannot be supported by this camera. Here are the descriptions of every setup item: Item Description Enable External...
Page 58: Sdhc
3-11 SDHC The IP camera has an optional Micro-SD card slot. The UI shows the capacity is 0 MB when the module without Micro-SD card slot and memory card. If you need the function please check the option when you place the order of the IP camera module.
Page 59 Set the time range then click “Search” then shows the records like below.
Page 60: Log
3-12 Log You can check the usage log of IP camera here. In this page, you can click: 1. First page / Final page: Jump to first / final page of log. 2. Previous / Next: Jump to previous or next page of log. 3.
Page 61: Device Info
3-13 Device Info You can check the information and network settings of this IP camera. This information is very useful when you need to repair or fix the problem of this IP camera. An example of device info page look likes this:...
Page 62: Maintenance
3-14 Maintenance You can do some maintenance job about this IP camera here. Here are the descriptions of every setup item: Item Description Reboot Click this button to reboot the IP camera. This function is useful when you find IP camera is not working properly.
Page 63: Language
Backup to SD Backup IP camera’s setting and save it on SD card. A card device SD card must be inserted into SD card slot when you click this button, or you’ll receive an error message. Restore Restore a previously-saved configuration file saved on your computer.
Page 64: Chapter Iv Troubleshooting
Chapter IV Troubleshooting Please don’t panic when you found this IP Camera is not working properly. Before you send this IP Camera back to us, you can do some simple checks to save your time: Problem description Possible solution(s) Can’t connect to IP 1) Please check the IP address of IP Camera Camera again.
Page 65 How to disassembly the bullet case? 1. The number shows the sequence of bullet case disassembly. 2. It is recommended that you use a tool with a hexagonal socket, such as the socket spanner pictured below. 3. Attach the socket spanner to the cable gland, and twist anti-clockwise to loosen the cable gland.
Page 66: Chapter V Digital I/O User Guide
Chapter V Digital I/O User Guide DI/DO connector – Use in applications for e.g. motion detection, event triggering, SD recording and alarm notiﬁcations via FTP/EMAIL/SAMBA. •Digital output — For connecting external devices such as relays, alarm bell or LEDs. Connected devices can be activated by the Configuration Event interface or digital output buttons on the Home page.
Page 67 •Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active. Notes Specifications DI is floating, trigger is “high”...
Page 68: Chapter Vi Specification
Chapter VI Specification SIU7117 Model No. 3MP Outdoor H.264 Day / Night IP Description Bullet Camera Max. Resolution 2048H x 1536V Format 1/3" Effective Pixels Image 2048H x 1536V Sensor Pixel size 2.2 x 2.2μm Active Image Area 4.51mm(H) x 3.38mm(V)
Page 69 Audio In / Out Two-way LED Indicators Power & Ethernet (1/1) RS-485 Reset Power Yes, IEEE802.3af compliant Supply AC-DC Power DV 12V Motion Detection Yes, 3 scalable windows Brightness, Contrast, Sharpness, Image Settings Saturation Adjustable 5 sec. pre-alarm / 5 sec. post-alarm, Alarm Buffer up to 3MByte Mirror...
Page 70 Physical Info. WEIGHT 910gm (Camera body only) DIMENSIONS φ73.0mm x 186.2mm (L)