Table of Contents
Related Manuals for OSCO MSG-A
Summary of Contents for OSCO MSG-A
-
Page 1: Installation Guide
MSG-A • MSG-D INSTALLATION GUIDE ® OPERATOR SPECIALTY COMPANY, INC. CASNOVIA, MI 49318 • U.S.A. UL325 COMPLIANCE REQUIRES THE USE OF CONTACT EDGES OR PHOTOELECTRIC CONTROLS ON ALL AUTOMATIC OR REMOTELY-CONTROLLED GATE OPERATORS. Aug. 2003, Rev. 15... -
Page 2: Table Of Contents
Model MSG-A Mechanical Parts Exploded View ........................... 24 Model MSG-A Mechanical Parts List ............................. 25 Model MSG-A Control Box Exploded View and Parts List ......................26 Model MSG-A Gate Arm Assembly Parts List ..........................27 Model MSG-D Mechanical Parts Exploded View ........................... 28 Model MSG-D Mechanical Parts List ............................. -
Page 3: Pre-Installation Information
Defective part(s) shall be repaired or re- tection devices have been approved for use with placed at no charge, at the manufacturer’s option. All OSCO swing gate operators as part of a UL325 com- accessories are covered by their manufacturer’s warranty. pliant installation: The manufacturer will not be responsible for trans- portation and/or field service charges. -
Page 4: Wiring Specifications
8760 Twisted Pair Shielded Cable (or equivalent) only – 4. All control devices are now 24VDC, which can be run con- OSCO part number 2500-1982, per foot). See page 10 for siderable distances. details of this connection, as well as dip switch selection. -
Page 5: Post And Pad Mounting Instructions
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE POST AND PAD MOUNTING INSTRUCTIONS FOR MODELS MSG-A MSG-D NOTE: Maximum gate opening angle is approximately 95 degrees, depending on gate width. If larger opening angle is required, non-standard positioning of the operator and modified articulating arms will be required. -
Page 6: String Method For Nonstandard Installation Of Swing Gate Operators
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE STRING METHOD FOR NONSTANDARD INSTALLATION OF SWING GATE OPERATORS Step A: Position the Operator 1. Connect the gate plate assembly onto the gate at the recommended location for a standard installation (Dimension “W”). 2. Open the gate to its fully-open position. -
Page 7: Articulating -Style Arm Assembly Instructions
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE ARTICULATING-STYLE ARM ASSEMBLY INSTRUCTIONS FOR MODELS MSG-A MSG-D Numbered items in these drawings are for instructional reference only. For actual part numbers, go to the parts lists in the back of this booklet. Slide 1/2” lockwasher and flatwasher onto 1/2-13 x 2 1/2”... -
Page 8: Vent Plug Installation
VENT PLUG INSTALLATION Gear reducers used in OSCO gate operators will have solid plugs installed prior to shipment in order to keep the oil inside from spilling out during shipping. A vent plug has been provided to replace this plug during installation. This plug will look similar to the ones shown below. -
Page 9: Electrical Connection And Adjustments
Keep clear of gate during operation. All OSCO gate operators are supplied with a power disconnect switch to turn on and off the power supply available to the operator. Incoming power should be brought into the operator and connected to the labeled pigtails in the disconnect box, following wiring specifications on page 4. -
Page 10: Control Board Adjustments
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE CONTROL BOARD ADJUSTMENTS LIMIT SWITCH L.E.D.s LIMIT SWITCH CONNECTOR TERMINAL STRIP #1 CONNECTOR 3A Fuse 2A Fuse BRAKE TERMINAL STRIP #2 DIAGNOSTIC RESISTOR CONNECTOR L.E.D.s NOTE: DO NOT FORCE 270-DEGREE POTENTIOMETERS BEYOND THEIR NORMAL RANGE OF MOTION... -
Page 11: Terminal Connection Descriptions
(See page 10 for details.) You must follow all required safety precautions and instructions at all times. Review the safety brochure included with the operator. If any pages are missing or unreadable, contact OSCO at 1-800-333-1717 to request additional copies. -
Page 12: Current Sensing Adjustments
Because gates vary in construction and may have different force requirements in the open and close directions to move, the OSCO control board has separate Multi-turn potentiometers for adjusting in both directions independently. The adjustment should be set light enough to maintain minimal force (40 lbs.) should an obstruction occur, but high enough to keep the gate moving under normal conditions without interruption. -
Page 13: Onboard L.e.d. Indicator Descriptions
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE ONBOARD L.E.D. INDICATOR DESCRIPTIONS Control Board L.E.D. Indicators: OPEN This indicator is lit when an open signal is present. This signal can come from such devices as button stations, radio receivers, keypads and telephone entry systems. -
Page 14: Important Notes For Installation Of Master/Slave Applications
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE IMPORTANT NOTES FOR INSTALLATION OF MASTER/SLAVE APPLICATIONS When setting up Master/Slave gate operators, it is best to make adjustments and run each operator individually. To do this, simply: a. Set Dip Switch #4 to proper hand of operation (right-hand or left-hand) b. -
Page 15: Charger Board Sleep Mode
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE CHARGER BOARD SLEEP MODE When primary AC power is not available, the operator will continue to JUMPER CAP WAKE operate in battery only mode if the charger board is set in its RUN mode... -
Page 16: Control And Accessory Connection Illustrations
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE CONTROL and ACCESSORY CONNECTION ILLUSTRATIONS - 16 -... - Page 17 MSG-A • MSG-D OPERATOR INSTALLATION GUIDE CONTROL and ACCESSORY CONNECTION ILLUSTRATIONS - 17 -...
- Page 18 MSG-A • MSG-D OPERATOR INSTALLATION GUIDE OSCO CONTROL and ACCESSORY CONNECTION ILLUSTRATIONS - 18 -...
-
Page 19: Control And Accessory Connection Illustrations
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE CONTROL and ACCESSORY CONNECTION ILLUSTRATIONS AC MODELS ONLY - 19 -... -
Page 20: Loop Layout Illustration
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE LOOP LAYOUT ILLUSTRATION Refer to Connection Descriptions on page 11 and Loop Accessory Connections on page 19 for additional details. - 20 -... -
Page 21: Edge Layout Illustration #1
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE EDGE LAYOUT ILLUSTRATION Refer to Connection Descriptions on page 11 and Contact Edge Connections on page 18 for additional details. - 21 -... -
Page 22: Photoeye Illustration
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE PHOTOEYE ILLUSTRATION Refer to Connection Descriptions on page 11 and Photoeye Connections on page 18 for additional details. - 22 -... -
Page 23: Troubleshooting
Replace if necessary. HOW TO ORDER REPLACEMENT PARTS Use the part numbers listed on the following pages. Contact your local OSCO dealer or distributor to order parts. 1. Supply the model number and serial number of your operator. -
Page 24: Model Msg-A Mechanical Parts Exploded View
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-A MODEL MECHANICAL PARTS EXPLODED VIEW - 24 - 5-03-14... -
Page 25: Model Msg-A Mechanical Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-A MODEL MECHANICAL PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION 2100-1614 Wrapper 2200-081 Gear Reducer 2110-698 Middle Shelf Assembly 2200-079 Single Pulley, 7” 2200-820 Bearing, 1” 2200-860 #40 Chain, 29 Links 2400-145 #40 Half Link... -
Page 26: Model Msg-A Control Box Exploded View And Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-A MODEL CONTROL BOX PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION 2100-1778 Control Box Wrapper 2300-696 Clear Control Box Cover 2100-1790 Control Box Mounting Plate 2100-1789 Control Box Slide Rail 2100-1762 Terminal Strip Bracket, Output Side... -
Page 27: Model Msg-A Gate Arm Assembly Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-A MODEL GATE ARM ASSEMBLY PARTS LIST PART NO. DESCRIPTION 2120-449-BT Complete Arm Assembly 2100-1465-BT Crank (not included in arm assembly) 2100-1722-BT Crank Extension 2100-1924-BT Overtravel Stop 2100-1597 Gate Arm Clamp 2100-1733-BT Gate Plate 2200-783 Spacer, 1/2”... -
Page 28: Model Msg-D Mechanical Parts Exploded View
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-D MODEL MECHANICAL PARTS EXPLODED VIEW - 28 - 5-03-14... -
Page 29: Model Msg-D Mechanical Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-D MODEL MECHANICAL PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION 2100-1614 Wrapper 2200-081 Gear Reducer 2110-698 Middle Shelf Assembly 2200-079 Single Pulley, 7” 2200-820 Bearing, 1” 2200-860 #40 Chain, 29 Links 2400-145 #40 Half Link... -
Page 30: Model Msg-D Control Box Exploded View And Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-D MODEL CONTROL BOX PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION 2100-1778 Control Box Wrapper 2500-2018 Fuse, 15 Amp 2100-1790 Control Box Mounting Plate (available in local hardware stores) 2100-1762 Terminal Strip Bracket, Output Side... -
Page 31: Model Msg-D Gate Arm Assembly Parts List
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE MSG-D MODEL GATE ARM ASSEMBLY PARTS LIST PART NO. DESCRIPTION 2120-449-BT Complete Arm Assembly 2100-1465-BT Crank (not included in arm assembly) 2100-1722-BT Crank Extension 2100-1924-BT Overtravel Stop 2100-1597 Gate Arm Clamp 2100-1733-BT Gate Plate 2200-783 Spacer, 1/2”... -
Page 32: Model Msg-D Battery Maintenance And Brush Replacement
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE BATTERY MAINTENANCE The gel-cell batteries in this operator require no routine maintenance. For assured continued performance, they should be replaced every year. If power is to be removed for one week or more, disconnect the negative wire from the batteries as this will prevent deep discharging. - Page 33 MSG-A • MSG-D OPERATOR INSTALLATION GUIDE Imperial Oil MATERIAL SAFETY DATA SHEET HANDLING, STORAGE AND SHIPPING: Keep containers closed. Handle and open Date Prepared: February 02, 1996 containers with care. Store in a cool, well ventilated place away from incompatible Supersedes: January 07, 1995 materials.
- Page 34 MSG-A • MSG-D OPERATOR INSTALLATION GUIDE - 34 - 8-03-15...
-
Page 35: Preventative Maintenance
• Keep clear of gate during operation. GENERAL: OSCO gate operators are designed for many years of trouble-free operation and, under recommended operating conditions, will require only minimal maintenance. To ensure that your unit is ready for operation at all times--and to preclude serious damage or failure--inspect the unit systematically. -
Page 36: Gate Operator Installation Checklist
MSG-A • MSG-D OPERATOR INSTALLATION GUIDE GATE OPERATOR INSTALLATION CHECKLIST INSTALLER CUSTOMER ________ ________ 1. The gate has been checked to make sure it is level and moves freely in both directions. ________ ________ 2. Potential pinch areas have been guarded so as to be inaccessible OR have contact and/or non-contact obstruction sensing devices installed.