DeWalt DWE6005-XE Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Laminate Trimmer
  5. DWE6005-XE
  6. Instruction manual
DeWalt DWE6005-XE Instruction Manual

DeWalt DWE6005-XE Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
DWE6005-XE
LAMINATE TRIMMER

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWE6005-XE

Summary of Contents for DeWalt DWE6005-XE

  • Page 1 INSTRUCTION MANUAL DWE6005-XE LAMINATE TRIMMER...

  • Page 3: Definitions: Safety Guidelines

    An estimation of the level of exposure to vibration should also take into account DWE6005-XE the times when the tool is switched off or when it is running but not actually doing Voltage the job.
  • Page 4 e) When operating a power tool outdoors, use an extension cord suitable WARNING: To reduce the risk of injury, user must read the instruction manual. for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

  • Page 5: Extension Cords

    b) Do not use the power tool if the switch does not turn it on and off. Any reduced physical, sensory or mental capabilities, or lack of experience and power tool that cannot be controlled with the switch is dangerous and must knowledge, unless they have been given supervision or instruction concerning be repaired.
  • Page 6 • Check to see that the cord will not snag or impede the trimming operation. Cutting into a nail can cause the bit and the tool to jump and damage the bit. • Use sharp bits. Dull bits may cause the laminate trimmer to swerve or stall under •...
  • Page 7 • The label on your tool may include the following symbols. The symbols and their definitions are as follows: FIG. 1 V ......volts A ......amperes Hz ....hertz W ......watts min ....minutes or AC ....alternating current or DC ..direct current or AC/DC ..alternating or ....Class I Construction ......direct current (grounded)

  • Page 8: Assembly And Adjustments

    ASSEMBLY AND ADJUSTMENTS FIG. 2 WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. FIG. 3 Inserting the Motor into the Fixed Base (Fig.
  • Page 9 Locking Lever Adjustment (Fig. 2) bits having 6.35 mm (1/4") diameter shanks. Bits are not included but are available as an accessory. Excessive force should not be used to clamp the locking lever (H). Using excessive force may damage the base. WARNING: Do not use bits with a diameter in excess of 25.4 mm (1 1/8") in this When the locking lever is clamped, the motor should not move in the base.
  • Page 10 OPERATION Adjusting the Depth of Cut (Fig. 8) 1. Select and install the desired bit. Refer to Bit Installation and Removal. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/ 2.

  • Page 11: Troubleshooting

    NOTE: To remove the edge guide, reverse the above procedure. After removing edge Troubleshooting guide, always replace the screw (T) into the storage hole on the back of the base to For assistance with your tool, visit our website at visit www.dewalt.com or call prevent it from being lost. 1-800-4-D WALT (1-800-338-002) .
  • Page 12 Accessories WARNING: Since accessories, other than those offered by D WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D WALT recommended accessories should be used with this product.
  • Page 16 Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (NOV13) Part No. N290040 DWE6005-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

Table of Contents