Subscribe to Our Youtube Channel
Related Manuals for STUDIO DUE CityColor IP54
Summary of Contents for STUDIO DUE CityColor IP54
- Page 1 INTERNATIONAL PATENT WO99/40361 User’s and operator’s manual for art. 0002•0003•0004•0005...
-
Page 2: Table Of Contents
Index Safety informations ..........................page 1 Technical features ..........................page 2 Main supply connection ........................page 3 Lamp installation, replacement and setting ..................page 4 Installation of the dust proof filters ....................... page 5 Control panel and configuration ......................page 6 Use of the CityColor in DMX 512 ...................... -
Page 3: Safety Informations
The CityColor projects, thanks to an extremely efficient optic system (international patent n. WO99/40361), a powerful light beam which can create numberless color shades. Its performances, in terms of luminousity and lighted surfaces, can reach incredible levels. The CityColor IP54 comes in four versions: • Art. 0002 CITYCOLOR for MHD 1800W discharge lamp •... -
Page 4: Technical Features
•Projector •N.2 plane reflectors “C” •User’s manual •Power connector •Termination resistor •Studio Due warranty Available on request: •Barn doors •Lamp WARNING Check that the spot has not been damaged during transport. If it has been damaged or it does not work, address the seller. - Page 5 IP 67 INPUT CONNECTOR FOR 1800W 3 PIN CONNECTOR FOR POWER INPUT L =1) NEUTRAL pict.1 N =2) LIVE =3) EARTH IP 67 INPUT CONNECTOR FOR 2500W HIGH POWER BEFORE USING The equipment must be earthed. WARNING IP 54 grade: the equipment must be installed on the horizontal plane.
- Page 6 pict.2 In case of replacement of the lamp or maintenance, do not open the fixture unless 5 minutes have passed from the switching off. WARNING This operation has to be done when the apparatus is disconnected from the mains supply INSTALLATION OF THE DISCHARGE LAMP MHD 1800W, MHD 2500W e HMD 2500W (art.
-
Page 7: Installation Of The Dust Proof Filters
IP RATE The declared IP rate of the CityColor comes supported at these conditions: • the installation of the fixture on a wide and stable surface • the air cooling input and output are located on the base of the side-shell, it is not possible to install the fixture outdoor with the ballast upwards •... - Page 8 pict.4 CONTROL PANEL On the control panel of the CityColor (pict.4) you can find, besides the display, the leds and the buttons to use to set the spot. • “DMX” led flashing:DMX input present off: no DMX input • ”LAMP” led flashing:the lamp switching off is remotely controlled off: lamp switched on...
- Page 9 SUMMARY OF THE PROGRAMMING FUNCTIONS OF THE CITYCOLOR Addr NChn Test Mode LHrs FLIP Rset FHrs About twenty seconds after the switching on, the number of the software version will be shown on the display in “X_00” format. Afterwards the first of the eight available menus will appear: Addr to assign the DMX-512 address Mode DMX512 mode, master with pre-set selection, slave...
- Page 10 NChn (Number of Channel) To visualise the number of channel press ENTER. Use Down and Up buttons to change the channel and, once the required one has been selected, press and keep ENTER pressed up to when the display stops flashing (it flashes to indicate that the selected option is different from the pre-set one). It is possible to set 6 channels or 7 channels ( remote reset and remote lamp switch off ).
- Page 11 CONNECTION THE DATA LINK (DMX 512) pict.5a pict.5 fig.5c fig.5b The connection of the DMX signal to the CITYCOLOR must be made by using the signal input XLR 5 pin connectors which are located on the control panel of the fixture. (pict.5) The pin nomenclature of the connectors for the connection to the DMX signal is listed in the table.
- Page 12 WARNING DMX TERMINAL LINE The wrong connection of the terminal line or its non-connection are probably the most frequent reasons for the defective functioning of the DMX line. The terminator is a resistor fitted between the two “data” lines (pins 2 and 3 of an XLR 5 pin connector) at the end of the cable furthest from the transmitter.
-
Page 13: Use Of The Citycolor In Dmx 512
MASTER pict.7 USE OF THE CITYCOLOR IN AUTO-MODE A short list of the games can be found in appendix “B”, page 13 Press the MENU button on the control panel up to when the option MODE (pict. 7) is shown on the display, select it by pressing EN- TER and the set indication will appear (no...SL). - Page 14 APPENDIX “A” Here below you can find the complete list of DMX values (ref. page 8) ... 12 ...
- Page 15 APPENDIX “B” Here below you can find the complete list of the available games (ref. page 11) ... 13 ...
-
Page 16: Appendix
• Description of the problem and the troubleshooting procedures that you have performed so far to diagnose and resolve the fault. You can contact your authorized STUDIO DUE dealer or directly STUDIO DUE l.d. Technical Service. (fax. +39.0761.352653 - e-mail: service@studiodue.com) - Page 17 D A T A L I N K ( 5 1 2 D M X ) T O U B L E S H O O T I N G D A T A L I N K ( 5 1 2 D M X ) T O U B L E S H O O T I N G Appendix “C”...
- Page 18 MAIN BOARD CONNECTION U5 U6 U7 U8 U9 L6219 MOTOR DRIVER U4 MICRO SLAVE MOTOR U3 MICRO MASTER MOTOR CCSLAVEXX U11 VIPER SWITCHING LED +5V CC3DRVXX POWER SUPPLY DRIVER LED +5V OPTO DMX U13 78M05 OPTO DMX TO DISPLAY PCB PAN IP LED DMX SIGNAL 320V DC...
- Page 19 MOTORS BOARD • POWER SUPPLY +30V Led On • +5V Led • +320V Led •+5V DMX Led • DMX signal Led flashing: the DMX signal is operating on the board Led off: check the U1 (6N137) and the DMX connecting cable (from PCB PAN IP) •...
- Page 20 Head Office: STUDIO DUE Light Division s.r.l. Str. Poggino, 100 - 01100 Viterbo (Italy) tel. +39 0761 352520 fax +39 0761 352653 Asia branch: STUDIO DUE Far East LTD Unit D 29/F West Gate Tower 7 Wing Hong Street Kln. Hong Kong tel.
Need help?
Do you have a question about the CityColor IP54 and is the answer not in the manual?
Questions and answers