Summary of Contents for Miller Electric Big Blue 500 PT
Page 1
Visit our website at www.MillerWelds.com Big Blue 500 PT Big Blue 600 X (Perkins Turbo-Powered) OM-4429 2216 138H 2007−05 Processes Stick (SMAW) Welding TIG (GTAW) Welding MIG (GMAW) Welding Flux Cored (FCAW) Welding Air Carbon Arc (CAC-A) Cutting and Gouging...
Page 2
ISO 9001:2000 Quality System Standard. particular model are also provided. Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets.
TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1-1. Symbol Usage ............... . 1-2.
Page 4
TABLE OF CONTENTS SECTION 7 − OPERATING WELDING GENERATOR − CC/CV MODELS 7-1. Front Panel Controls For CC/CV Models (See Section 7-2) 7-2. Description Of Front Panel Controls For CC/CV Models (See Section 7-1) 7-3. Process/Contactor Switch On CC/CV Models 7-4.
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text.
Page 6
FUMES AND GASES can be hazardous. Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. D Keep your head out of the fumes. Do not breathe the fumes. D If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases.
1-3. Engine Hazards BATTERY EXPLOSION can BLIND. D Always wear a face shield, rubber gloves, and protective clothing when working on a battery. D Stop engine before disconnecting or connect- ing battery cables or servicing battery. D Do not allow tools to cause sparks when working on a battery. D Do not use welder to charge batteries or jump start vehicles.
HOT METAL from air arc cutting and gouging can cause fire or explosion. D Do not cut or gouge near flammables. D Watch for fire; keep extinguisher nearby. HOT PARTS can cause burns and injury. D Do not touch hot compressor or air system parts.
H.F. RADIATION can cause interference. D High-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment. D Have only qualified persons familiar with electronic equipment perform this installation. D The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
SECTION 2 CONSIGNES DE SÉCURITÉ − LIRE AVANT − Se protéger, ainsi que toute autre personne travaillant sur les lieux, contre les étincelles et le métal chaud. 2-1. Signification des symboles DANGER! − Indique une situation dangereuse qui si on l’évite pas peut donner la mort ou des blessures graves.
Page 11
DES PIÈCES CHAUDES peuvent provoquer des brûlures graves. D Ne pas toucher à mains nues les parties chau- des. D Prévoir une période de refroidissement avant de travailler à l’équipement. D Ne pas toucher aux pièces chaudes, utiliser les outils recomman- dés et porter des gants de soudage et des vêtements épais pour éviter les brûlures.
LES CHAMPS MAGNETIQUES peuv- ent affecter des implants médicaux. D Porteur de simulateur cardiaque ou autre im- plants médicaux, rester à distance. D Les porteurs d’implants doivent d’abord consulter leur médecin avant de s’approcher des opérations de soudage à l’arc, de sou- dage par points, de gougeage, du coupage plasma ou de chauf- fage par induction.
L’utilisation d’un groupe autonome à l’intérieur PEUT VOUS TUER EN QUELQUES MINUTES. D Les fumées d’un groupe autonome contient du monoxyde de carbone. C’est un poison invisi- ble et inodore. D JAMAIS utiliser dans une maison ou garage, même avec les portes et fenêtres ouvertes. D Uniquement utiliser à...
Page 14
LE SURCHAUFFEMENT peut endom- mager le moteur électrique. D Arrêter ou déconnecter l’équipement avant de démarrer ou d’arrêter le moteur. D Ne pas laisser tourner le moteur trop lentement sous risque d’en- dommager le moteur électrique à cause d’une tension et d’une fré- quence trop faibles.
2-6. Proposition californienne 65 Avertissements Les équipements de soudage et de coupage produisent des fumées et des gaz qui contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils provoquent des mal- formations congénitales et, dans certains cas, des cancers. (Code de santé...
3-3. Symbols And Definitions Some symbols are found only on CE products. Stop Engine Starting Aid Check Injectors/ Pump Positive Amperes Engine Stick (SMAW) Welding Time Three Phase Electrode Connection Duty Cycle Rated Idle Speed Contactor On OM-4429 Page 14 Fast (Run, Weld/ Power) Battery (Engine)
4-3. Volt-Ampere Curves For CC Models DC AMPERES Notes OM-4429 Page 16 Ranges 300−Max 185−425 125−320 85−190 55−90 The volt-ampere curve shows the minimum and maximum voltage and amperage output capabilities of the welding generator. Curves of all other settings fall between the curves shown.
4-4. Volt-Ampere Curves For CC/CV Models A. Stick Mode 200 300 400 B. MIG Mode C. TIG Mode DC AMPERES Ranges 275−Max 150−525 110−390 80−240 50−125 500 600 DC AMPERES 500 600 900 1000 DC AMPERES Ranges 50−440 35−320 25−215 15−115 The volt-ampere curves show the minimum and maximum voltage...
4-7. AC Generator Power Curve AC AMPERES IN 240V MODE AC AMPERES IN 120V MODE 4-8. Optional Three-Phase Generator Curves A. 12 kVA/kW Single-Phase AC Output (No Weld Load) B. 20 kVA/kW Three-Phase AC Output (No Weld Load) AC AMPERES AC AMPERES The ac power curve shows the gen- erator power in amperes available...
SECTION 5 − INSTALLATION 5-1. Installing Welding Generator Movement Location/Airflow Clearance 18 in (460 mm) 18 in (460 mm) 18 in (460 mm) (460 mm) Grounding GND/PE OM-4429 Page 20 18 in (460 mm) 18 in Always securely fasten weld- ing generator onto transport vehicle or trailer and comply with all DOT and other applica-...
5-2. Using Lifting Eye Notes Lifting Eye Carriage Bolt Raise lifting eye until it snaps in place. Lower lifting eye when not needed. To lock the lifting eye in the upright position, insert a 3/8-16 x 1-1/2 in carriage bolt through slot in bracket and secure with nut (bolt and nut not supplied).
5-3. Mounting Welding Generator Supporting The Unit Using Mounting Brackets Tools Needed: 9/16 in OM-4429 Page 22 Welding Unit In Place Bolting Unit In Place install3 2007−04 803 274 / 200 864-A / 803 602 Do not weld on base. Weld- ing on base can cause fuel tank fire or explosion.
5-4. Installing Exhaust Pipe Tools Needed: 1/2 in Notes Stop engine and let cool. Point exhaust pipe in desired di- rection but always away from front panel and direction of travel. Ref. 803 604 / Ref. 215 158 Work like a Pro! Pros weld and cut safely.
5-5. Activating The Dry Charge Battery (If Applicable) 5 A For 30 Minutes 30 A For 12 Minutes Tools Needed: 5-6. Connecting The Battery Connect negative (−) cable last. Tools Needed: 1/2 in OM-4429 Page 24 − − Always wear a face shield, rubber gloves and protective clothing when working on a battery.
5-7. Engine Prestart Checks Full Diesel Check all engine fluids daily. Engine must be cold and on a level surface. Unit is shipped with 20W break-in oil. Automatic shutdown system stops engine if oil pressure is too low, coolant temperature is too high, or engine overspeeds.
5-9. Selecting Weld Cable Sizes* Weld Output Terminals Stop engine before Welding connecting to weld Amperes output terminals. Do not use worn, dam- aged, undersized, or poorly spliced cables. Chart is a general guideline and may not suit all applications. If cables overheat, use next size larger cable. **Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
5-11. Connecting To Remote 14 Receptacle RC14 On CC/CV Models New! LDR-14 long distance remote distance remote (includes 120 V receptacle) *The remaining sockets are not used. Notes Start Your Professional Welding Career Now! OM-4429 Page 28 24 VOLTS AC 24 VOLTS AC REMOTE OUTPUT...
6-2. Description Of Front Panel Controls For CC Models (See Section 6-1) Engine Starting Controls Starting Aid Switch Use switch to energize starting aid for cold weather starting (see starting instructions fol- lowing). Engine Control Switch Use switch to start and stop engine. To Start: NOTICE −...
6-3. Remote Amperage Control On CC Models (Optional) Example: Combination Remote Amperage Control (Stick) Set Switches Set Range 6-4. Weld Control/Arc Condition Information Label OM-4429 Page 32 Remote Amperage Adjust Receptacle RC13 Connect optional remote control to RC13 (see Section 5-10). In Example: Range = 115 to 330 A DC Percentage Of Range = 50%...
7-2. Description Of Front Panel Controls For CC/CV Models (See Section 7-1) Engine Starting Controls Starting Aid Switch Use switch to energize starting aid for cold weather starting (see starting instructions fol- lowing). Engine Control Switch Use switch to start engine, select engine speed ( if unit has auto idle option), and stop engine.
7-4. Remote Voltage/Amperage Control On CC/CV Models (Optional) Example: Combination Remote Amperage Control (Stick) Set Remote Set V/A Adjust Switch Process Example: Combination Remote Amperage Control (TIG) Set V/A Set Remote Process Adjust Switch Process = Stick (Using Remote On/Off) Set Range Control Not Used In Remote...
SECTION 8 − OPERATING AUXILIARY EQUIPMENT 8-1. 120 Volt And 240 Volt Receptacles OM-4429 Page 38 120 V 20 A AC GFCI Receptacle GFCI1 240 V 30 A AC Twistlock Receptacle RC1 Receptacles supply 60 Hz single- phase power at weld/power speed. If a ground fault is detected, GFCI Reset button...
8-2. Connecting To Optional Three-Phase Generator (CC/CV Models Only) Single-Phase Power Connection Three-Phase Power Connection Y Close panel opening if no connections are made to generator. Remove plug before inserting leads. Reinstall bushing. Rear Of Panel 120V 120V Single Phase Output Volts 120/240...
8-3. Optional Generator Power Receptacles European Receptacle Australian Receptacle South African Receptacle OM-4429 Page 40 120 V 20 A AC GFCI Receptacle GFCI1 240 V 16 A AC European Receptacle RC1 240 V 15 A AC Australian Receptacle RC1 240 V 15 A AC South African Receptacle RC1 Receptacles supply 60 Hz single- phase power at weld/power speed.
9-2. Routine Maintenance n = Check Z = Change * To be done by Factory Authorized Service Agent Every FUEL WATER Hours n Fuel/Water Separator n Fuel Level n Coolant Level Every Hours ~ Weld Terminals Every Hours ~ Battery Terminals n Air Cleaner Hoses Every Hours...
9-3. Servicing Air Cleaner Keep nozzle 2 in (51 mm) from element. Blow Optional Inspect aircleaner1 9/00 − ST-153 929-B / ST-153 585 / Ref. S-0698-B / Ref. 215 158 Stop engine. NOTICE − Do not run engine without air cleaner or with dirty element.
9-6. Servicing Fuel And Lubrication Systems Stop engine and let cool. After servicing, start engine and check for fuel leaks. Stop engine, tighten connec- tions as necessary, and wipe up spilled fuel. Oil Filter Oil Drain Valve And Hose Oil Fill Cap Fuel Line Primary Fuel Filter (Fuel/ Water Separator)
9-7. Overload Protection OM-4429 Page 46 Stop engine. When a supplementary protector, circuit breaker or fuse opens, it usu- ally indicates a more serious problem exists. Contact Factory Authorized Service Agent. Fuse F1 Fuse F2 F1 and F2 protect the stator exciter wind- ing from overload.
9-8. Troubleshooting A. Welding − CC Models Trouble No weld output; generator power output Check position of Ampere Range switch. okay at ac receptacles. Check position of optional Polarity switch. Place Amperage Adjust switch in Panel position, or place switch in Remote position and connect remote control to Remote Amperage Adjust receptacle RC13 (see Sections 5-10 and 6-1).
Page 52
B. Welding − CC/CV Models Trouble No weld output; generator power output Place Process/Contactor switch in a Weld Terminals Always On position, or place switch in a Remote okay at ac receptacles. On/Off Switch Required position and connect remote contactor to optional Remote 14 receptacle RC14 (see Sections 5-11 and 7-1).
Page 53
Trouble Check and secure connections to Remote 14 receptacle RC14 (see Section 5-11). Repair or replace wire feeder. Low CV weld output. Set Ampere Range switch to highest range. Increase Voltage/Amperage Adjust Control setting. Min or max CV weld output only. Check position of Voltage/Amperage Adjust control and Voltage/Amperage Adjust switch.
Page 54
Trouble Check engine wiring harness plug connections. Have Factory Authorized Service Agent check control relay CR1, diode/capacitor board D8/C8, and En- gine Control switch S1. Engine cranks but does not start. Check fuel level. Check battery and replace if necessary. Check engine charging system according to engine manual. Have Factory Authorized Service Agent check engine wiring harness, time delay relay TD1, control relay CR5, fuel pump, fuel solenoid FS1, and diode/capacitor board D10/C10.
Page 55
Notes Start Your Professional Over 80,000 trained 400 Trade Square East, Troy, Ohio 45373 Welding Career Now! since 1930! 1-800-332-9448 www.welding.org OM-4429 Page 51...
SECTION 11 − RUN-IN PROCEDURE 11-1. Wetstacking OM-4429 Page 56 run_in1 2007−04 NOTICE − Do not perform run-in procedure at less than 20 volts weld output and do not exceed duty cycle or equipment damage may occur. Welding Generator Run diesel engines near rated volt- age and current during run-in period to properly seat piston rings and prevent wetstacking.
11-2. Run-In Procedure Using Load Bank Stop engine. Do not touch hot exhaust pipe, engine parts, or load bank/grid. Keep exhaust and pipe away from flammables. NOTICE − Do not perform run- in procedure at less than 20 volts weld output and do not exceed duty cycle or equip- ment damage may occur.
11-3. Run-In Procedure Using Resistance Grid OM-4429 Page 58 Stop engine. Do not touch hot exhaust pipe, engine parts, or load bank/grid. Keep exhaust and pipe away from flammables. NOTICE − Do not perform run- in procedure at less than 20 volts weld output and do not exceed duty cycle or equip- ment damage may occur.
SECTION 12 − GENERATOR POWER GUIDELINES The views in this section are intended to be representative of all engine-driven welding generators. Your unit may differ from those shown. 12-1. Selecting Equipment 12-2. Grounding Generator To Truck Or Trailer Frame GND/PE Generator Power Receptacles −...
12-3. Grounding When Supplying Building Systems 12-4. How Much Power Does Equipment Require? OM-4429 Page 60 GND/PE VOLTS 115 AMPS Equipment Grounding Terminal Grounding Cable Use #10 AWG or larger insulated copper wire. Ground Device Use ground device as stated in electrical codes.
Page 65
12-5. Approximate Power Requirements For Industrial Motors Industrial Motors Split Phase Capacitor Start-Induction Run Capacitor Start-Capacitor Run Fan Duty 12-6. Approximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Stock Tank De-Icer Grain Cleaner Portable Conveyor Grain Elevator Milk Cooler Milker (Vacuum Pump) FARM DUTY MOTORS Std.
Page 66
12-7. Approximate Power Requirements For Contractor Equipment Contractor Hand Drill Circular Saw Table Saw Band Saw Bench Grinder Air Compressor Electric Chain Saw Electric Trimmer Electric Cultivator Elec. Hedge Trimmer Flood Lights Submersible Pump Centrifugal Pump Floor Polisher High Pressure Washer 55 gal Drum Mixer Wet &...
Page 67
12-8. Power Required To Start Motor Motor Start Code KVA/HP 12-9. How Much Power Can Generator Supply? Single-Phase Induction Motor Starting Requirements 10.0 AC MOTOR VOLTS AMPS CODE PHASE 11.2 12.5 Motor Start Code Running Amperage Motor HP Motor Voltage To find starting amperage: Step 1: Find code and use table to find kVA/HP.
Page 68
12-10. Typical Connections To Supply Standby Power Utility Electrical Transfer Switch Service Essential Loads OM-4429 Page 64 Fused Welding Disconnect Generator Switch Output (If Required) Have only qualified persons perform these connections according to all applicable codes and safety practices. Properly install and ground this equipment according to its Owner’s Manual and na-...
Page 69
12-11. Selecting Extension Cord (Use Shortest Cord Possible) Cord Lengths for 120 Volt Loads If unit does not have GFCI receptacles, use GFCI-protected extension cord. Current Load (Watts) (Amperes) 1200 1800 2400 3000 3600 4200 4800 5400 6000 *Conductor size is based on maximum 2% voltage drop Cord Lengths for 240 Volt Loads If unit does not have GFCI receptacles, use GFCI-protected extension cord.
SECTION 13 − PARTS LIST Hardware is common and not available unless listed. 114 (Fig.13−7) 115 (CV) 116 (CV) 111 (Fig. 13−2 OR Fig. 13-3 109 (CC) 108 (CC) 121 (Fig.13−4 OR 13−5) Figure 13-1. Main Assembly OM-4429 Page 66...
Page 80
Hardware is common and not available unless listed. 803 649 Figure 13-4. Panel, Front w/Components − CC Models Item Dia. Part Mkgs. Figure 13-4. Panel, Front w/Components − CC Models (Figure 13-1 Item 121) ....215 070 .
Page 81
Item Dia. Part Mkgs. Figure 13-4. Panel, Front w/Components − CC Models (Continued) ....215 014 ....217 883 .
Page 82
Hardware is common and not available unless listed. Figure 13-5. Panel, Front w/Components − CC/CV Models Item Dia. Part Mkgs. Figure 13-5. Panel, Front w/Components − CC/CV Models (Figure 13-1 Item 121) ....215 158 .
Page 85
Item Dia. Part Mkgs....210 446 ....024 617 .
Page 86
Hardware is common and not available unless listed. Item Dia. Part Mkgs....215 910 ....188 137 .
Page 87
Some wiring harness components (switches, relays, circuit breakers) are also referenced elsewhere in this parts list. Purchase components sepa- rately or as part of the associated wiring harness. Item Dia. Part Mkgs..... 221374 .
Page 89
Warranty Questions? LIMITED WARRANTY − Subject to the terms and conditions Call below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to 1-800-4-A-MILLER its original retail purchaser that new Miller equipment sold after the effective date of this limited warranty is free of defects in for your local material and workmanship at the time it is shipped by Miller.
Page 90
File a claim for loss or damage during shipment. For assistance in filing or settling claims, contact your distributor and/or equipment manufacturer’s Transportation Department. 2007 Miller Electric Mfg. Co. 2007−01 Miller Electric Mfg. Co. An Illinois Tool Works Company 1635 West Spencer Street Appleton, WI 54914 USA International Headquarters−USA...