Table of Contents
Advertisement
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio or television technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Important Note
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter, except the transmitters built-in with the device.
FCC Hearing-Aid Compatibility (HAC) Regulations for Wireless Devices
On July 10, 2003, the U.S. Federal Communications Commission (FCC) Report and Order in WT Docket 01- 09
modified the exception of wireless phones under the Hearing Aid Compatibility Act of 1988 (HAC Act) to require
digital wireless phones be compatible with hearing-aid. The intent of the HAC Act is to ensure reasonable access
to telecommunications services for persons with hearing disabilities. While some wireless phones are used near
some hearing devices (hearing aid and cochlear implants), users may detect a buzzing, humming, or whining
noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in
the amount of interference they generate. The wireless telephone industry has developed a rating system for
wireless phones, to assist hearing device users find phones that may be compatible with their hearing devices.
Not all phones have been rated. Phones that are rated have the rating on their box or a label located on the box.
The ratings are not guarantees. Results will vary depending on the user's hearing device and hearing loss. If your
hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully.
Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate
less interference to hearing devices than phones that are not rated. M4 is the better/
higher of the two ratings. Your device is rated M4.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more
usable with a hearing aid's telecoil than phones that are not rated. T4 is the better/
higher of the two ratings. Your device is rated T4. Please power off the Bluetooth
function while using hearing aid devices with your ALCATEL A564C.
Hearing devices may also be rated. Your hearing device manufacturer or hearing health professional may help
you find this rating. Higher ratings mean that the hearing device is relatively immune to interference noise. The
hearing aid and wireless phone rating values are then added together. A sum of 5 is considered acceptable for
normal use. A sum of 6 is considered for better use. A sum of 8 is considered for best use. In the above example,
if a hearing aid meets the M2 level rating and the wireless phone meets the M3 level rating, the sum of the two
values equal M5. This should provide the hearing aid user with "normal usage" while using their hearing aid
with the particular wireless phone. "Normal usage" in this context is defined as a signal quality that is acceptable
for normal operation.
This methodology applies equally for T ratings. The M mark is intended to be synonymous with the U mark. The
T mark is intended to be synonymous with the UT mark. The M and T marks are recommended by the Alliance
for Telecommunications Industries Solutions (ATIS). The U and UT marks are referenced in Section 20.19 of
the FCC Rules. The HAC rating and measurement procedure are described in the American National Standards
Institute (ANSI) C63.19 standard.
For information about hearing aids and digital wireless phones
FCC Hearing Aid Compatibility and Volume Control:
http://www.fcc.gov/cgb/dro/hearing.html
Gallaudet University, RERC:
https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm
SAR Information
0.73 W/kg @ 1g (HEAD)
0.753W/kg @ 1g (BODY)
THIS MODEL DEVICE MEETS THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. For
body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with
the TCT Mobile Limited. Accessories supplied or designated for this product. Use of other accessories may not
ensure compliance with the FCC RF exposure guidelines.
Your wireless mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed
the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission
of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF
energy for the general population. The guidelines are based on the safety standards previously set by both U.S.
and international standards bodies:
•
American National Standards Institute (ANSI) IEEE. C95.1-1992 .
•
National Council on Radiation Protection and Measurement (NCRP). Report 86. 1986.
•
International Commission on Non- Ionizing Radiation Protection (ICNIRP) 1996.
•
Ministry of Health (Canada), Safety Code 6. The standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phone employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg*.
The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as
in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC
and can be found under the Display Grant section of https://fjallfoss. fcc.gov/oetcf/eas/reports/GenericSearch.
®
cfm after searching on FCC ID: RAD476 Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications & Internet Association (CTIA) Web-site as http://http://www.ctia.org/.
* In the U.S. and Canada, the SAR limit for mobile phone used by the public is 1.6 Watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for
the public and to account for any variations in usage. Normal condition only to ensure the radiative performance
and safety of the interference. As with other mobile radio transmitting equipment, users are advised that for
satisfactory operation of the equipment and for the safety of personnel, it is recommended that no part of the
human body be allowed to come too close to the antenna during operation of the equipment.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum
Advertisement
Table of Contents
