Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Audiolab 8300CD
Summary of Contents for Audiolab 8300CD
- Page 1 8300CD User Instructions...
-
Page 2: Important Safety Information
The exclamation point within an equilateral triangle is Mains Supply: The mains operating voltage of Audiolab intended to alert the user to the presence of important Refer all servicing to qualified service personnel. Servicing 8300 series units is shown on the rear panel. -
Page 3: Getting Started
If you wish to connect the outputs of 8300CD into a pre-amplifier, you may wish to disable the volume control functions, so that the player operates at a fixed gain. In this mode the unit More than just a CD player, 8300CD is a versatile digital decoder that will serve you for many years to come. -
Page 4: Controls And Connectors
3: Controls and Connectors Page 3... -
Page 5: Remote Handset
NOTE: the handset buttons shown crossed out are for use with other 4: Remote Handset Audiolab units and are not operational when used with the 8300CD Fitting Batteries 1 STANDBY Press to bring the unit in/out of Standby 2 STORE... -
Page 6: Balanced Output
Make sure the the appropriate input of the 8300CD. ON/OFF switch on the 8300CD is switched off. Switch the mains supply off at the wall socket, and then, using the cable supplied, connect the socket on the back If you are connecting a multichannel source, access the menu of the source of your 8300CD to an AC supply outlet. -
Page 7: Operation
Trk 12 58:14 Press to eject the disc to bring 8300CD out of standby, the power indicator LED becomes brighter, after Next/Previous Track -20dB a short period the units boots up,the display shows the welcome screen You can activate the ‘auto standby’ function by holding the button down for 3 seconds. -
Page 8: Info Display
1 Trk 03m51s STORE to save. If there is a digital volume control on the source unit, set it at maximum and use the volume control in the 8300CD to alter the -28dB To play the program: Press 2 Trk 07m15s volume level. - Page 9 Selecting a Digital Filter: Playing a USB input -28dB 8300CD has 7 filters available for PCM audio. Press the FILTER key once to Unlocked Install the Audiolab Audio Driver from the CD-ROM provided as accessory. The display current PCM filter, Press the FILTER key again to change filters. Or press...
-
Page 10: The Menu Tree
The menu enables you to customize the unit and optimize the interface with other equipment in your system. 8300CD has 14 different menu pages. Press MENU key to enter menu mode, and then press to turn to different menu pages, press... -
Page 11: Warranty
8: Warranty Audiolab Ltd. warrants this product, subject to the terms and conditions below, to be free from defects Repairs or replacements as provided under this warranty are the exclusive remedy of the consumer. in materials and workmanship. During the warranty period Audiolab will repair or replace (at Audiolab’... -
Page 12: Specifications
9: Specifications (Measurement made with 230V power supply) 4.2Vrms ±0.1 (Balanced) Output Voltage 2.1Vrms ±0.1 (Unbalanced) Output Impedance 10Ω Total Harmonic Distortion (THD) <0.002% (1kHz, 0dB, 20Hz ~ 20kHz, A weighted) Frequency Response 20Hz - 20kHz (± 0.2dB) <-100dB A Weighted (Balanced) Signal to Noise Ratio (S/N) <-98dB A Weighted (Unbalanced) >100dB (Balanced) - Page 16 Audio lab IAG House, 13/14 Glebe Road, Huntingdon, Cambridgeshire, PE29 7DL, Tel: +44(0)1480 452561 Fax: +44(0)1480 413403 http://www.audiolab.co.uk CODE: AH14-MNL0004a...