Related Manuals for Gearmore T34B
Summary of Contents for Gearmore T34B
- Page 1 LOG SPLITTERS NGINE RIVEN RAILER OUNTED Assembly, Parts & Operator's Manual For Model T34B March 2007 Form: T34BLogsplit.pm7...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION DESCRIPTION PAGE Introduction .............. 1 Specifications ............1 Safety ................2 Training & Preparation .......... 3 Safety Wear ............. 3 Operating Safety ............. 4 Operating Procedure ..........5 Repair & Maintenance Safety ........ 5 Towing Safety ............6 Fire Prevention ............ -
Page 3: Introduction
Operator's Manual. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your dealer, or Gearmore if you need assistance, information or additional copies of the manuals. SPECIFICATIONS *Ideal case cycle time. Actual cycle time will vary depending on temperature,... -
Page 4: Safety
SAFETY SAFETY ALERT SYMBOL This Safety Alert symbol means The Safety Alert symbol identifies ATTENTION! BECOME important safety messages on the ALERT! YOUR SAFETY IS Log Splitter and in the manual. INVOLVED! When you see this symbol, be alert to the possibility of personal injury or death. -
Page 5: Training & Preparation
TRAINING & PREPARATION Read and thoroughly understand all NEVER wear loose clothing or jewelry that can ARNING instructions and safety infor- be caught by moving parts of your Log Splitter mation before assembling or and pull you into it. Keep clothing away from all operating this log splitter. -
Page 6: Operating Safety
GENERAL SAFETY WORK AREA SAFETY Failure to follow these instructions may OPERATE IN SAFE ENVIRONMENT AND ON SAFE GROUND result in serious injury or death. 1. NEVER operate your NEVER allow children or adults lacking proper Log Splitter on slippery, instructions and understanding to operate this wet, muddy or icy surfaces. -
Page 7: Operating Procedure
REPAIR & MAINTENANCE SAFETY OPERATING PROCEDURE Good maintenance is your responsibility. Poor ♦ ♦ ♦ ♦ ♦ ONLY operate the Log Splitter from the maintenance is an invitation to trouble. operator zone. Follow good shop practices. Keep service area clean •... -
Page 8: Towing Safety
TOWING SAFETY FIRE PREVENTION NEVER operate your log splitter near a flame or ALWAYS check all local and state regulations spark. Hydraulic oil and gasoline are flammable regarding towing, licensing, and lights before and can explode. towing your log splitter. DO NOT fill the gas tank while the engine is hot BEFORE towing, be certain that the log splitter or running. -
Page 9: Hydraulic Safety
Only a qualified service technician should perform this adjustment. SAFETY DECALS Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals. Contact your local dealer or Gearmore for free replacements. Part No. DL52-2-10 Part No. - Page 10 SAFETY DECALS (Continued) ALWAYS REPLACE WARNING MISSING OR DAMAGED DECALS 1. READ AND UNDERSTAND OPERATOR’S MANUAL THOROUGHLY BEFORE OPERATION. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY. 2. KEEP ALL SHIELDS IN PLACE. 3. KEEP HANDS, FEET AND CLOTHING AWAY FROM POWER DRIVEN PARTS.
-
Page 11: Assembly Instructions
ASSEMBLY INSTRUCTIONS NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the unit for repair or replacement parts. STEP 1: Remove all the components from the STEP 4: Stand the beam (1)* up on end. -
Page 12: Operation
OPERATING INSTRUCTIONS STEP 1: Starting FILLING HYDRAULIC SYSTEM Fill the hydraulic reservoir with at least five gallons of WARNING: Read thoroughly hydraulic fluid. After the hydraulic reservoir and the understand all instructions and safety engine crankcase are filled with oil, start the engine. information before operating this log The hydraulic pump should prime itself. -
Page 13: Towing
MAINTENANCE TOWING The Log Splitter is equipped with pneumatic tires, a Class I coupler (2" diameter ball required) and safety chains. Before towing the safety chains must be By following a good maintenance program, your secured to the hitch or bumper of the vehicle. Local equipment will last for many years. -
Page 14: Parts Breakdown
PARTS BREAKDOWN... -
Page 15: Parts List
PARTS LIST REF # QTY. PART NO. DESCRIPTION LS401148 Beam LS401190 Tank/Axle LS401261 Tongue HC390129 5" x 24" Hydraulic Cylinder HC390406S Auto-Return Valve LS401183 Wedge HC390524 10.5 H.P. Industrial/Commercial Engine HC390601 Filter HC390601A Filter Element (see list of equivalent filter elements) HC390601B Filter Base HC390709... - Page 16 PARTS LIST REF # QTY. PART NO. DESCRIPTION LS400429 Breather Cap Obtain Locally " NC Hex Nut Obtain Locally " Lockwasher Obtain Locally " NC x 4 " Hex Cap Screw HC390249 " I.D. x 37" Hydraulic Return Hose HC390316 Hose Clamp #16 P71022WC "...
-
Page 17: Limited Warranty
Our obligation shall be limited to repairing or replacement of any part, provided that such part is returned within thirty (30) days from date of failure to Gearmore through the dealer from whom the purchase was made, transportation charges prepaid.