Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS 1.Product Code Illumination and Series Introduction Model Identification 9 ─ □ □ □ □ A: Abbreviation of dishwasher B: Code name of Nominal capacity C: Series of factory design D: Freestanding/built –in/semi-built-in E: Mechanical/Electronic...
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS 3. Safety Precaution NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;...
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS 4.Net dimension 5.Installation and Accessory Parts 5.1 Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned on the right or the left to facilitate proper installation.
Page 6
Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Connect the cold water supply hose to a threaded 3/4(gas) connector and make sure that it is fastened tightly in place (see Fig 1).If the water pipes are new or have not been used for an extended period of time,let the water run to make sure that the water is clear and free of impurities.If this precaution is not taken,there is a risk that the water inlet can get blocked...
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS 6.Parts and Functions...
Page 8
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher,deposits will form on the dishes utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Page 9
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS It is recommended that adjustments be made in accordance with the following scheme: Detergent Detergent specifically intended for use with dishwashers must be used.The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table."...
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Maintenances Services and Trouble Shooting 8.1 Maintenances Services It may occur that the dishwasher does not function or does not function properly Before calling for assistance,Iet us see what can be done first:have you forgotten to press one of the buttons or to perfom an essential operation? 8.2 Trouble Shooting...
Page 14
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Water supply trouble Phenomenon: water level cannot reach the required location Whether water is flowing in the hose Turn on the stopcock Whether the stopcock is turned on Whether solenoid valve measure whether solenoid valve...
Page 15
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Drain pump trouble Phenomenon: water cannot be drained Repair the pipeline and drain pump Whether the pipeline Whether drain and drain pump was pump is working blocked Whether drain The drain hose is too...
Page 16
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Phenomenon: program controller stop turnning Check: Whether socket connector is connected well Connect it well Whether thermo limiter is change thermo limiter Whether heater is OK change heater Program controller or circuit is broken...
Page 17
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS Whether water is deposited is Whether water flows out of Bottom the bottom case the water overflow conduit case is leaking Check whether the water change the water level switch is closed level switch...
Page 18
Version:00.00 Edition: 2008.04 Dishwasher Model: HEC9AFM/HEC9AFMS check whether the power connector Connect it properly check whether the power connector is in position is in position check whether the circuit the cable or the controller board between the two terminals should be suspected...