Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Roline 21.11.3043
Summary of Contents for Roline 21.11.3043
- Page 1 User's Guide Gigabit Ethernet Adapter...
-
Page 2: Fcc Statement
FCC STATEMENT The adapter has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,... -
Page 3: Ec Declaration Of Conformity (Europe)
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. EC DECLARATION OF CONFORMITY (EUROPE) In compliance with the EMC Directive 89/336/EEC, the adapter meets the requirements of the following standards: EN55022 EN55024 SAFETY NOTICES... -
Page 4: Chapter 1 Introduction
Thank you for purchasing 10/100/1000M Gigabit Ethernet Adapter. This document provides detailed guidelines to install and use the adapter for network installers or users. The Giga Ethernet Adapter is a 32-bit PCI 10/100/1000Mbps NWay Gigabit LAN adapter. The Giga Ethernet Adapter provides extremely fast data transfer rates up to 2000Mbps at full duplex mode for high bandwidth usage in areas such as network servers, workstations, Storage Area Networks (SANs), Network Attach Storage (NAS) and high-speed... - Page 5 802.1P for packet prioritization. With 802.1Q support, server resources can be shared with multiple VLANs when used in conjunction with any 802.1Q- enabled Switch. With the 802.1p support, The Giga Ethernet Adapter allows a range of Ethernet packets to be prioritized from a critical to a non-critical designation through a priority tag.
- Page 6 Features & Advantages Integrated Ethernet MAC, Physical chip and transceiver in one chip Complies with the IEEE802.1P, IEEE802.1Q, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T standard Compliant to PCI Revision 2.1/2.2/2.3 Supports Full Duplex Flow Control (IEEE 802.3x) PCI local bus single-chip Ethernet controller Supports ACPI, PCI power management Supports Auto-Negotiation function, Auto-detects network speed...
-
Page 7: Chapter 2 Installation
Chapter 2 Installation Card Installation To insert The Product into your computer, follow the steps list below. Turn off the computer and remove its cover. Insert The Giga Ethernet Adapter into a PCI slot. Fix the Product to the rear of the computer chassis and put the computer cover in order. -
Page 8: Troubleshooting
Appendix A: Troubleshooting If you experience any problems with the adapter, first please confirm that the appropriate driver is loaded properly,and that the cable is connected to the adapter port soundly. Then check the LED. The Product provides LEDs to indicate network status. 10 LED, 100 LED, 1000 LED They all indicate Link/Active/Speed status. -
Page 9: Appendix B: Technical Specification
Appendix B: Technical Specification Topology: Star Connector Supported: RJ45 Standard: IEEE802.1P, IEEE802.1Q , IEEE802.3 10Base-T IEEE802.3u 100Base-TX IEEE 802.3ab 1000Base-T Transmission Rate: 10/20Mbps , 100/200Mbps, 2000Mbps Hardware: IBM PC compatibles(It must have PCI slot) IRQ Line: Assigned by system I/O Address: Assigned by system Software: Supports Drivers for NetWare 4.x,5.x,6.x, Windows 98, Windows ME, Windows NT, Windows 2000, Windows XP, Linux...
Need help?
Do you have a question about the 21.11.3043 and is the answer not in the manual?
Questions and answers