Related Manuals for BBV Tx40X
Summary of Contents for BBV Tx40X
- Page 1 Installation Guide Tx40X Telemetry transmitter Building Block Video Ltd www.bbvcctv.com 17 Apex Park, Diplocks Way, Hailsham, East Sussex, BN27 3JU, UK Tel: +44 (0) 1323 842727 Support: +44 (0) 1323 444600...
-
Page 3: Table Of Contents
Contents Important Introduction Unpacking A simple Tx40X up the coax system Tx40X connecting a Breakout box Keypad functions Lens action Auxiliary function switches Receiver self test Iris level program Presets Patrols 10 - 11 Spare outputs Sending # Commands Selecting protocols on the Tx40X... -
Page 4: Important
If the unit does not operate normally by following the operating instructions. If the unit has been dropped or the enclosure is damaged; Replacement parts - If replacement parts are required, ensure that only replacement parts recommended by the product manufacturer are used. Tx40X manual V1.06 July 2015... -
Page 5: Introduction
Introduction The Tx40X is very easy to use keypad for single up the coax controlled camera or single/multiple RS485/422 controlled camera CCTV systems. It is easily installed into either a new or an existing system simply by connecting a BNC input and output, or the twisted pair cable and a 12Vdc supply. -
Page 6: Tx40X Connecting A Breakout Box
Up to 1200m of twisted pair 12Vdc BBV Receiver NC = 6 PROGRAM PROGRAM AUTOPAN AUTOPAN 0V Supply = 7 +12V optional input 0V Supply = 8 +12V optional input Break out box Tx40X Tx40X connecting to a Breakout box Tx40X manual V1.06 July 2015... -
Page 7: Keypad Functions
PAN RIGHT TILT DOWN Lens Actions There are four lens function switches on the Tx40X keypad. These are IRIS OPEN, IRIS CLOSE, FOCUS NEAR and FOCUS FAR. ZOOM IN & ZOOM OUT are controlled via the joystick. Clockwise will zoom in and anti clockwise with zoom out, twist joystick until the desired picture is obtained. -
Page 8: Auxiliary Function Switches
Auxiliary Function Switches There are four auxiliary function switches on the Tx40X keypad: AUTOPAN WASH Press and hold for washer motor to run WIPE Latching output, press on/press off the button goes red to signify on AUTOPAN Press, button turns on and the Autopan motor starts. Panning Left or Right stops Autopan... -
Page 9: Presets
Select the preset to be erased, then press and hold PROGRAM then press and release IRIS OPEN. For example, to erase Preset 4, press and release preset key 4, press and hold PROGRAM, then press and release IRIS OPEN. PROGRAM Tx40X manual V1.06 July 2015... -
Page 10: Patrols
Each BBV receiver is capable of operating two patrol modes made up of the 16 presets. The Tx40X will only control the first 9 presets. When a preset is programmed it is automatically entered into both patrols. Presets can be removed from either patrol to make up the required sequences. - Page 11 Programming the Patrol delay (This function is only available for BBV coax): The default delay is 30 seconds. To programme a different delay, first determine the time delay required from the table below: Preset Key 1 Random switching from 0 to 100 seconds...
-
Page 12: Spare Outputs
If this does not work either then you will need to consult the camera manufacture and enquire how to enter the menu this may not be supported by the Tx40X. Protocols selection: The Tx40X transmits BBV Up The Coax and 1 of the supported RS422/485 protocols: BBV RS422 Pelco D 2400 N 8 1... -
Page 13: Tx40X Camera Address Selection
1. The keypad will remember the camera number that you are controlling even after you power down the keypad. Tx40X manual V1.06 July 2015... -
Page 14: Self Test On Keypad
The keypad supports a self test for in the field testing. This will enable the services engineer to confirm the functionality on the Tx40X in the field. To perform this test you will need to make a Loop Back test cable. - Page 15 24Vac or 110Vac. This option must be specified at the time of order. The Rx45X MK5 is designed to control fixed speed AC pan & tilts heads from BBV and Baxall up-the-coax telemetry and a range of BBV485/422 telemetry protocols.
- Page 16 These combinations provide a flexible, cost- effective control solution for both internal and external pan / tilt / zoom and dome applications. Like all BBV products, simplicity of use and aesthetic casework are inherent Tx1000 in the design.
Need help?
Do you have a question about the Tx40X and is the answer not in the manual?
Questions and answers