General Safety Information: Do not expose the pocket jump starter to rain, moisture or any liquid. Exposure to liquid or moisture may cause the pocket jump starter to fail and increase the risk of electrical shock or fire. Do not use this pocket jump starter if it should become wet. Make sure this pocket jump starter is insulated from water if you have to use it in the rain or snow.
Page 4
Caution: Make sure that you plug in the jump starter socket fully before trying to jump start the vehicle. If not, there is a chance that you cannot jump start your vehicle and melt the connection in the plug at the same time Before jump starting your vehicle, make sure the battery clamps are securely connected, clean the battery terminal if it appears to be corroded, or dirty.
Page 5
Always exercise care when you are using this jump starter. This pocket jump starter is not intended for use by children. Do not use this pocket jump starter in an explosive environment, such as in the presence of flammable liquid, gases or combustible dust. Do not modify or disassemble this pocket jump starter, only a certified tech may perform repair on this device.
B. OPERATION GUIDANCE Battery Indicator Press the switch to check the battery level. The number shown indicates the remaining battery capacity. Recharging the pocket jump starter: Using the 110V wall outlet: 1. Plug in the charger included into the wall outlet. 2.
For jump starting a vehicle with 12 volt battery system: Note 1: This jump starter will start gasoline engines in passenger vehicles, pickup trucks, and diesel engine vehicles with less than 3.0 liter displacements. Check the battery level before jump starting the vehicle. It is recommended to recharge the battery before jump starting a vehicle if the battery level is below 50%.
Page 9
a.) Plug in the Smart battery clamp to the jump starter socket. Press and hold the power button on the controller until the blue indicator comes on. Then start your engine. b.) If a car battery is not present or Power Override completely dead (disconnect the dead...
Page 10
When the engine starts, disconnect the jumper cable from the pocket jump starter and battery terminals within 30 seconds. Leave the engine running. Note 2: If the voltage is too low on the car battery, you may need to disconnect the cables from your car battery.
For charging smartphones or portable devices: 1. Plug in your own USB cable or use the 4 in 1 USB cable provided with this kit to the USB 2A output port. 2. The pocket jump starter will autodetect and start charging the phone or tablet when it is connected.
C. Lithium Battery Caring Tips This product uses a lithium polymer battery. We recommend that the battery is fully charged and discharged during first three uses to ensure the battery is in it’s best performance. When charging is complete, unplug the wall charger and disconnect the charger. Please do not place the jump starter in extreme environments.
D. FAQ: How to turn off this pocket jump starter? This device will power off automatically when no load is detected or when charging is complete. How many times can this device charge my cell phone? You can fully recharge your smartphone from 0% up to 3 times, depending on your phone’s battery capacity.
E. Troubleshooting Problem Solution No response when pressing the The low voltage protection of the pocket switch button. jump starter is activated. Plug the adapter into the charging port to recharge. Connect to car battery, still no power. The terminals may be corroded, clean the corroded terminals and try again.
Page 15
Solution Problem The jumper cable is not Return to Jackco for inspection and repair. Request RMA at functioning/broke. www.jackco.com/warranty.html...
F. Limited One (1) Year Warranty Jackco Transnational Inc. warrants “ZETA by JACKCO” branded products to the original purchaser against any manufacturing defect in material or worksmanship for a period of one (1) year from the original date of purchase. If the defective product is determined to be covered under this warranty, it shall be repaired or replaced at manufacturer’s discretion without charge.
G. Environmental Protection Do not dispose of the product with household waste. Do not incinerate. Keep away from fire. H. Technical Specifications Model ZT50410 Dimensions (L x W x H) 5.31 x 3.14 x 1.06 in. Weight 11.5 oz, 326 g...
Page 18
This product is manufactured for Jackco Transnational Inc. Made In China For Technical Assistance, Contact us by (888) 4JACKCO www.jackco.com...