Related Manuals for HP MS-6579
Summary of Contents for HP MS-6579
- Page 1 Getting Started Chapter 1. Getting Started Getting Started ® ® ® TOPICS Mainboard Specification Mainboard Layout Quick Components Guide...
-
Page 2: Mainboard Specification
Chapter 1 Mainboard Specification ® ® ® Chipset ® ® ® Main Memory Slots On-Board IDE... -
Page 3: Chapter 1. Getting Started
Getting Started On-Board Peripherals Audio BIOS Dimension Mounting Others... -
Page 4: Mainboard Layout
Chapter 1 Mainboard Layout MS-6579 v1.X M-ATX Mainboard... -
Page 5: Quick Components Guide
Getting Started Quick Components Guide... -
Page 6: Table Of Contents
Hardware Setup Chapter 2. Hardware Setup Hardware Setup TOPICS Central Processing Unit: CPU Memory Power Supply Back Panel Connectors 2-13 Jumpers 2-20 Slots 2-22... -
Page 7: Central Processing Unit: Cpu
Chapter 2 Central Processing Unit: CPU ® ® make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. Open Lever Sliding Plate Gold Arrow Close Lever Overheating will seriously damage the CPU and system, always make sure the cooling fan can work properly to protect the CPU from overheating. - Page 8 Hardware Setup retention mechanism levers...
- Page 9 Chapter 2 fan power cable then...
-
Page 10: Memory
Hardware Setup Memory DDR DIMM Slots (DDR 1~2) - Page 11 Chapter 2 Slot Momory Module Total Memory Slot 1 64MB, 128MB, 256MB, 64MB~512MB (Bank 0 & 1) 512MB Slot 2 64MB, 128MB, 256MB, 64MB~512MB (Bank 2 & 3) 512MB Maximum System Memory Supported 64MB~1GB TIP: You can barely see the golden finger if the module is properly inserted in the socket.
-
Page 12: Power Supply
Hardware Setup Power Supply CONN1 CONN1 Pin Definition SIGNAL SIGNAL JPW1 JPW1 Pin Definition SIGNAL... -
Page 13: Back Panel
Chapter 2 Back Panel Mous e Parallel L-in L-out MIC-in Keyboard COM A ® ® ® Pin Definition SIGNAL DESCRIPTION PS/2 Mouse (6-pin Female) -
Page 14: Hardware Setup
Hardware Setup ® ® ® Pin Definition SIGNAL DESCRIPTION PS/2 Keyboard (6-pin Female) USB Port Description SIGNAL DESCRIPTION 1 2 3 4 5 6 7 8 USB Ports... - Page 15 Chapter 2 Pin Definition 1 2 3 4 5 SIGNAL DESCRIPTION 6 7 8 9 9-Pin Male DIN Connector Line-Out Line-In Mic-In Line-In Line-Out MIC-In 2-10...
- Page 16 Hardware Setup Pin Definition SIGNAL DESCRIPTION 2-11...
- Page 17 Chapter 2 RJ-45 Activity Indicators LAN Jack (RJ-45) LAN Jack Pin Definition SIGNAL DESCRIPTION USB Port Description SIGNAL DESCRIPTION 1 2 3 4 5 6 7 8 USB Ports 2-12...
-
Page 18: Connectors
Hardware Setup Connectors FDD1 2-13... - Page 19 Chapter 2 SECON1 PRIMAR1 PRIMAR1 SECON1 If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions.
- Page 20 Hardware Setup JCD1 JAUX1 2-15...
- Page 21 Chapter 2 +12V SENSOR C_FAN1 +12V SENSOR S_FAN1 Note: Always consult the vendor for proper CPU cooling fan. 2-16...
- Page 22 Hardware Setup ® JFP1 JFP1 Switch/LED Front Panel Electrical Connection SIGNAL DESCRIPTION 2-17...
- Page 23 Chapter 2 USB HDD digital cameras MP3 players printers modems and the like ® JUSB1 JUSB1 Pin Definition Description Description 2-18...
- Page 24 Hardware Setup JSP1 Pin Definition SIGNAL JSP1 Speaker Riser Card (optional) Connected to JSP1 Connected to stereo speakers 2-19...
-
Page 25: Jumpers
Chapter 2 Jumpers Clear CMOS Keep CMOS JBAT1 Note: To clear CMOS, first make the #2-3 pin short connected after the system is off. And then power on the system and short connect #1-2 pin before entering the BIOS (Standard CMOS Features) to clear data. 2-20... - Page 26 Hardware Setup GPIO 3.3V Standby JPWD1 Clear Normal 2-21...
-
Page 27: Slots
Chapter 2 Slots AGP Slot PCI Slots 1.5V 2x/4x 2-22... - Page 28 Hardware Setup Order 1 Order 2 Order 3 Order 4 PCI Slot 1 INT F# INT G# INT H# INT E# PCI Slot 2 INT G# INT H# INT E# INT F# PCI Slot 3 INT D# INT A# INT B# INT C# LAN Controller INT H#...