Do you have a question about the Fourtrax Foreman TRX400FW 1997 and is the answer not in the manual?
Questions and answers
Joseph L Gordon
May 5, 2025
How do I change the oil and filter on a 1997 Honda Forman 400
2 comments:
Joseph L Gordon
May 5, 2025
@Joseph L Gordon
Mr. Anderson
May 18, 2025
To change the oil and filter on a 1997 Honda Fourtrax Foreman TRX400FW, follow these steps:
Tools and Materials Needed: - 10mm and 17mm socket or wrench - Drain pan - Funnel - New oil filter - Fresh engine oil (approx. 3.2 quarts of 10W-40) - Clean rag
Steps:
1. Warm Up the Engine: - Start and run the engine for a few minutes to warm the oil. Then shut it off.
2. Place ATV on Level Ground: - Ensure the ATV is on a flat, stable surface.
3. Drain the Oil: - Locate the oil drain bolt under the engine (17mm bolt). - Place a drain pan beneath it. - Remove the bolt and let the oil fully drain.
4. Remove the Oil Filter: - The oil filter cover is on the right side of the engine. - Remove the three 10mm bolts holding the cover. - Take off the cover and remove the old filter. - Note the orientation of the old filter and spring behind it.
5. Install New Oil Filter: - Place the spring behind the new filter (if required). - Insert the new filter with the rubber seal facing out. - Reinstall the cover and tighten the bolts evenly.
6. Reinstall the Drain Bolt: - Once oil is drained, reinstall and tighten the drain bolt securely.
7. Add New Oil: - Remove the oil fill cap. - Using a funnel, pour in about 3.2 quarts of 10W-40 oil. - Replace the oil fill cap.
8. Check Oil Level: - Start the engine and let it run for a minute. - Turn it off and wait 2–3 minutes. - Check the oil level using the dipstick and add oil if needed.
9. Check for Leaks: - Inspect around the drain bolt and oil filter area for leaks.
Dispose of the old oil and filter properly.
This answer is automatically generated
john
June 1, 2025
1997 honda forman grease fitting location
1 comments:
Mr. Anderson
June 1, 2025
The 1997 Honda Fourtrax Foreman TRX400FW has grease fittings (also called zerks) typically located on the front upper and lower suspension arms (A-arms) near the ball joints and possibly on the rear suspension components. These fittings allow you to apply grease to the suspension pivot points to maintain smooth operation and reduce wear. Not all models have grease fittings on every joint, so visual inspection is recommended to locate them.
This answer is automatically generated
Related Manuals for Honda Fourtrax Foreman TRX400FW 1997
Need help?
Do you have a question about the Fourtrax Foreman TRX400FW 1997 and is the answer not in the manual?
Questions and answers
How do I change the oil and filter on a 1997 Honda Forman 400
@Joseph L Gordon
To change the oil and filter on a 1997 Honda Fourtrax Foreman TRX400FW, follow these steps:
Tools and Materials Needed:
- 10mm and 17mm socket or wrench
- Drain pan
- Funnel
- New oil filter
- Fresh engine oil (approx. 3.2 quarts of 10W-40)
- Clean rag
Steps:
1. Warm Up the Engine:
- Start and run the engine for a few minutes to warm the oil. Then shut it off.
2. Place ATV on Level Ground:
- Ensure the ATV is on a flat, stable surface.
3. Drain the Oil:
- Locate the oil drain bolt under the engine (17mm bolt).
- Place a drain pan beneath it.
- Remove the bolt and let the oil fully drain.
4. Remove the Oil Filter:
- The oil filter cover is on the right side of the engine.
- Remove the three 10mm bolts holding the cover.
- Take off the cover and remove the old filter.
- Note the orientation of the old filter and spring behind it.
5. Install New Oil Filter:
- Place the spring behind the new filter (if required).
- Insert the new filter with the rubber seal facing out.
- Reinstall the cover and tighten the bolts evenly.
6. Reinstall the Drain Bolt:
- Once oil is drained, reinstall and tighten the drain bolt securely.
7. Add New Oil:
- Remove the oil fill cap.
- Using a funnel, pour in about 3.2 quarts of 10W-40 oil.
- Replace the oil fill cap.
8. Check Oil Level:
- Start the engine and let it run for a minute.
- Turn it off and wait 2–3 minutes.
- Check the oil level using the dipstick and add oil if needed.
9. Check for Leaks:
- Inspect around the drain bolt and oil filter area for leaks.
Dispose of the old oil and filter properly.
This answer is automatically generated
1997 honda forman grease fitting location
The 1997 Honda Fourtrax Foreman TRX400FW has grease fittings (also called zerks) typically located on the front upper and lower suspension arms (A-arms) near the ball joints and possibly on the rear suspension components. These fittings allow you to apply grease to the suspension pivot points to maintain smooth operation and reduce wear. Not all models have grease fittings on every joint, so visual inspection is recommended to locate them.
This answer is automatically generated