Download Print this page

Advertisement

Operating and Installation
Instructions
Freezer
with Ice/Water Dispenser
F 1471 SF
en - US, CA
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
M.-Nr. 07 360 780

Advertisement

   Related Manuals for Miele F 1471 SF

   Summary of Contents for Miele F 1471 SF

  • Page 1

    Operating and Installation Instructions Freezer with Ice/Water Dispenser F 1471 SF en - US, CA To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 07 360 780...

  • Page 2: Installation Instructions

    Installation instructions To prevent accidents and machine damage read these instructions before installation or use.

  • Page 3: Caring For The Environment

    Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling center about the possibility of recycling these materials.

  • Page 4: Installation Site

    Empty weight of your machine: The ambient temperature should not drop below 55°F (13°C) or rise above F 1471 SF ..364 lbs (165 kg) 110°F (43°C), otherwise malfunctions may occur.

  • Page 5

    F 1471 SF ..558 lbs (253 kg) To ensure that the appliance is installed Installation niche...

  • Page 6: Installation Options

    "Merging Kit". The "Merging Kit" can be obtained from The door hinge cannot be Miele. exchanged. Contact Miele or your dealer for specific information about which Single column combinations will work with your The appliance can be installed at any appliance.

  • Page 7: Side Panels

    "Merging Kit". The "Merging Kit" can be obtained from Miele. Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured...

  • Page 8

    Dimensions Niche dimensions F 1471 SF 18 ½" (469.8 mm) 18" (457 mm)

  • Page 9

    Dimensions Power supply and water connection Door dimensions (open 115°) " (525 mm) " (234 mm) F 1471 SF...

  • Page 10

    Dimensions...

  • Page 11: Installing The Appliance

    Installing the appliance Before you begin Tools needed for installation – Cutter with adjustable blade Read these instructions completely and carefully. – Cordless screwdriver T 20 Have the appliance installed by a – Torx screwdriver T 20 qualified technician, according to the enclosed installation instructions.

  • Page 12: Check The Installation Niche

    Installing the appliance Check the installation niche Before installation To ensure a safe, trouble-free Caution - the appliance is very installation and the best possible heavy. Use caution when unpacking cosmetic result, check to be sure and opening the door, danger of that the installation space complies tipping.

  • Page 13: Remotevision Module Installation

    If the indicator light does not come on, The slot for the RemoteVision module is installation of the module was located in the lower area of the back of unsuccessful. In that case, repeat the your appliance. process. If that does not correct the problem, contact Miele.

  • Page 14: Preparing The Installation Niche

    Installing the appliance Preparing the installation niche Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard. ^ Pull the antenna d straight out. ^ Guide the cover b over the antenna d and screw on the cover. If the installation niche is deeper than ^ Angle the antenna d so that it faces the appliance, a solid wooden beam a...

  • Page 15

    Installing the appliance Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). ^ Drill pilot holes: – " (3 mm) for 5 x 60 mm wood screws –...

  • Page 16

    Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower If the anti-tip brackets cannot be attached securely, an alternative edge of the beam) on the rear wall of anti-tip device can be used.

  • Page 17: Sliding The Appliance Into The Installation Niche

    Installing the appliance Sliding the appliance into the The plug of the appliance should be installation niche easily accessible after installation. If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.

  • Page 18: Aligning The Appliance

    Installing the appliance Aligning the appliance A mark is located on the appliance base and is used as a standard gauge ^ Align the appliance with the for height adjustment. When adjusting surrounding cabinets. the height, align this mark at 1 "...

  • Page 19: Attaching The Appliance To The Installation Niche

    Installing the appliance Note: If there is a fairly large gap above the appliance, cut a wooden beam to fit – Do not twist or jam the appliance exactly and place it in the gap. inside the niche. When unscrewing the height-adjustable feet, proceed Now connect the water supply to the gradually, alternating between left...

  • Page 20

    Installing the appliance Mounting the air separator The air separator on the inside of the freezer door keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ Remove the foil from the adhesive strips.

  • Page 21

    Installing the appliance Aligning the Ice/Water Dispenser If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance. Disconnect the appliance from the power supply.

  • Page 22

    Installing the appliance Once the drip tray has been removed, the four aligners can be accessed to adjust the Ice/Water Dispenser to your liking. ^ Loosen the screws of the four ^ Pull the rear cover forward and out. clamps. ^ Insert a screwdriver into one of the four slots and push sideways until the dispenser is aligned with the custom...

  • Page 23: Attaching The Frame And The Shelf

    Installing the appliance Attaching the frame and the shelf " (19 mm) thick custom doors: ^ Slide the cover frame onto the Ice/Water Dispenser and press until it is flush with the door surface (be sure the word "TOP" on the cover frame is upward).

  • Page 24

    Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply.

  • Page 25

    Plumbing Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker...

  • Page 26: Connecting The Water Supply

    Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to ^ Push the end of the water pipe into the solenoid valve of the appliance, the appliance connection and screw follow the instructions supplied by on the union nut, 3.

  • Page 27: Electrical Connection

    If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435...

  • Page 28

    Alteration rights reserved / 3009 M.-Nr. 07 360 780 / 04 F 1471 SF For the most updated manual see the Miele web site.

Comments to this Manuals

Symbols: 0
Latest comments: