Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Intraphex Manuals
  4. Recording Equipment
  5. P1N-GM11
  6. Installation manual

Intraphex P1N-GM11 Installation Manual

Prodigy-one.2 navigation integration module
Hide thumbs

Advertisement

Quick Links

Download this manual
P1n-gm11
INST ALLATION
MANUAL
Prodigy*one.2
na vigation
INTEGRA TION MODULE
This manual shows the install into a gmc terrain. Other
vehicle disassembly will vary. wiring remains the same
with all vehicles.
See application guide for applicable vehicles

Advertisement

loading
Need help?

Need help?

Do you have a question about the P1N-GM11 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Intraphex P1N-GM11

Summary of Contents for Intraphex P1N-GM11

  • Page 1 P1n-gm11 INST ALLATION MANUAL Prodigy*one.2 na vigation INTEGRA TION MODULE This manual shows the install into a gmc terrain. Other vehicle disassembly will vary. wiring remains the same with all vehicles. See application guide for applicable vehicles...
  • Page 2 Cont acts www.INTRAPHEX.com SUPPORT@INTRAPHEX.COM SUPPORT: 810.355.2266 EXT 4 Fax: 866.431.0676 FACETIME VIDEO TECH SUPPORT: VSUPPORT@INTRAPHEX.COM...
  • Page 3 What’s In The Box VIDEO INTERFACE INSTALL/USERS   GUIDES PRODIGY*ONE.2  GPS ANTENNA  MAIN T-HARNESS  MICROPHONE  GVIF T-HARNESS  INTRAPHEX MOUSE  MONITOR T-HARNESS  CONNECTOR TWO  8GB SD CARD WITH  INTRAPHEX NAV SOFTWARE...
  • Page 5 INTERFACE DIP SWITCH SETTINGS DIP 1 A/V 1 ON A/V 1 OFF DIP 2 A/V 2 ON A/V 2 OFF DIP 3 A/V 3 ON A/V 3 OFF DIP 4 AFTERMARKET CAMERA OEM CAMERA  DIP SWITCH SETTINGS MUST BE PERFORMED WITH UNIT POWERED OFF. IT WILL NOT CAUSE DAMAGE, BUT THE FUNCTION WILL NOT BE RECOGNIZED UNTIL POWER CYCLES.

  • Page 7: Button Functions

    RADIO CONTROL PANEL BUTTON FUNCTIONS  BUTTON FUNCTIONS ARE DETERMIDED BY THE “VEHICLE” TYPE CHOSEN IN THE INTERFACE SETTINGS MENU. IF THEY ARE NOT PERFORMING AS STATED IN THE TABLE BELOW, ENTER THE SETTINGS MENU AND CHANGE “VEHICLE” TYPE. WHEN PRESSED IN FACTORY BUTTON WHEN PRESSED IN NAV SCREEN SCREEN...
  • Page 8  REMOVE MONITOR HOOD BY PULLNG UP ON FRONT. SET ASIDE.  REMOVE RADIO CONTROL PANEL. GENTLY PULL PN LOWER PART OF PANEL TO RELEASE, THERE ARE NO SCREWS. UNPLUG HVAC/RADIO CONNECTOR. SET ASIDE.  REMOVE FOUR 7MM SCREWS SECURING FACTORY MONITOR IN PLACE.
  • Page 9  REMOVE FOUR 7MM SCREWS HOLDING CD/12VOLT POCKET IN PLACE. PLACE SHIFTER IN “D” POSITION, AND REMOVE POCKET. UNPLUG 12VOLT SOCKET. SET ASIDE.  REMOVE FOUR 7MM SCREWS HOLDING LOWER SECTION OF UPPER DASH. THIS WILL ALLOW THE DASH TO FLEX TO REMOVE THE FACTORY RADIO/CD.
  • Page 10  ALL COMPONETS REMOVED FROM DASH.  REMOVE PASSENGER SIDE OF CENTER CONSOLE. NO SCREWS, JUST CLIPS. SET PANEL ASIDE.  ROUTE GVIF T-HARNESS FROM FACTORY LOCATION DOWN TO PASSENGER FLOOR BOARD NEAR FUSE BOX.  ROUTE MONITOR T-HARNESS TO LOCATION BEHIND FACTORY RADIO.
  • Page 11  PLUG BOTH T-HARNESSES INTO FACTORY CONNECTORS, AND TUCK HARNESS INSIDE OF SUBFRAME LEAVING ONLY THE TWO MALE CONNECTORS FOR THE MONITOR OUT.  PLUG MONITOR T-HARNESS 4PIN INTO 44PIN MAIN T-HARNESS.  ROUTE WHITE CONNECTORS FROM 44PIN MAIN T-HARNESS BEHIND PLASTIC DOWN TO PASSENGER FLOOR BOARD.
  • Page 12  ROUTE CABLES BEHIND FUSEBOX, ALLOWING THE CONNECTORS TO EXIT ON THE BOTTOM. THIS IS WHERE THE INTERFACE WILL RESIDE.  PLUG TWO CONNECTORS INTO INTERFACE. THE OTHER CONNECTORS SHOWN IN THIS PICTURE (3PIN & 2PIN) ARE FOR DVD IR AND ARE NOT NEEDED UNLESS INSTALLING AN AFTERMARKET DVD PLAYER NEEDING TOUCH CONTROL.
  • Page 13  ROUTE 24PIN BLACK CONNECTOR FOR PRODIGY*ONE.2 FORWARD. PLUG INTO PRODIGY*ONE.2 (PRODIGY*MINI SHOWN). PLUG 20PIN “CONNECTOR TWO” INTO PRODIGY*ONE.2. ROUTE OPEN USB TO ACCESSABLE LOCATION FOR MOUSE.  ROUTE MICROPHONE AND GPS ANTENNA FROM DESIRED LOCATIONS AND CONNECT TO PRODIGY*ONE.2. GPS ANTENNA CAN BE MOUNTED UNDER PLASTIC, BUT NEEDS A CLEAR VIEW OF THE SKY.
  • Page 14  PLUG GVIF AND MONITOR T-HARNESS INTO FACTORY MONITOR AND REMOUNT MONITOR WITH FOUR 7MM SCREWS.  REPLACE THE RADIO CONTROL PANEL. AT THIS POINT YOU SHOULD BE ABLE TO PERFORM SETUP AND ADJUSTMENTS, BEFORE RE-ISTALLATION OF ALL TRIM PANELS. ...
  • Page 15  ONCE INSIDE THIS MENU, IT WILL BE NECISSARY TO SET THE INTERFACE UP FOR DESIRED OPERATION. CHOOSE VEHICLE TYPE. THIS WILL CHOOSE HOW RADIO CONTROL BUTTONS FUNCTION. SEE FUNCTION DIAGRAM TYPE 1 EQUINOX, TERRAIN, CRUZE, ECT TYPE 2 MALIBU ...

  • Page 16: Touch Screen Calibration

    TOUCH SCREEN CALIBRATION  USING THE MOUSE (PLUGGED INTO THE OPEN USB FROM EARLIER) CLICK ON THE SETTINGS TAB.  ENTER PASSWORD “7777” THEN PRESS OK TO ENTER SETTINGS MENU.  CLICK ON THE “CALIBRATION” ICON.  NOW USING YOUR FINGER (FROM DRIVER TOUCH AND SIDE OF CAR FOR BEST RESULTS)

  • Page 17: Navigation Software

     DO NOT CHANGE ANY OF THE OTHER SETTINGS INSIDE OF THE SETTINGS MENU. THEY ARE ALL SET TO DEFAULT. CHANGING ANY OF THESE SETTINGS WILL CAUSE ERRATIC BEHAVIOR OR CAUSE THE SCREEN TO GO BLACK. IF THIS HAPPENS CALL TECH SUPPORT FOR ASSISTANCE.

  • Page 18: Adjusting The Gain

    ADJUSTING THE GAIN  LOCATE GAIN CONTROL ON INTERFACE. USING A SMALL SCREW DRIVER YOU CAN ADJUST THE OUTPUT OF THE NAVIGATION VOLUME.  USING THE VOLUME SETTING FOR VOICE, YOU CAN PRESS THE CIRCLE AND IT WILL REPEAT A PROMPT SO THAT YOU CAN SET THIS CORRECTLY.
  • Page 19 RE-ASSEMBLY  ONCE PROPER FUNCTION HAS BEEN ACHIEVED, YOU CAN RE-ASSEMBLE THE VEHICLE.  BE SURE TO REPLACE ALL REMOVED SCREWS AND TRIM PANELS.  BE SURE TO LEAVE NAVIGATION QUICK START GUIDE AND USER INSTRUCTIONS IN THE VEHICLE FOR THE CUSTOMER.
  • Page 20 SCAN THE IMAGE ABOVE WITH YOUR MOBILE PHONE TO GET MORE INFORMATION ABOUT INTRAPHEX PRODUCTS...
  • Page 21 INTRAPHEX warrants to the original retail purchaser, that the product(s) purchased from an INTRAPHEX authorized dealer, in the original vehicle, are free from defects in materials or workmanship under normal use and conditions for a period of THREE (3) years from date of purchase.