Vax Performance V-091 Instruction Manual page 4

V-091 U-G aw 21/10/05 10:56 am Page 7
Dirt Container & Filters: Removal & Replacement / Storage
6. Dirt Container & Filters: Removal
& Replacement
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before removing the dirt
container.
IMPORTANT: Do NOT use the vacuum cleaner
without ALL of the filters in place.
Emptying the Dirt Container
1. Press the button located on the dirt container
handle to pull out the dirt container (Fig.6/1)
Fig.6/1
2. Lift up the safety latch (Fig.6/2)
Fig.6/2
3. Press the button located under the safety latch
to empty the dirt into a rubbish bin. When all
of the dirt has fallen, close the dirt container
flap, close the safety latch and replace the dirt
container.
Cleaning the Filter
1. Remove the dirt container as directed.
2. Release the filter safety latch located on top of
the dirt container and pull out the central filter
unit.
3. Remove the filter shroud by rotating it anti-
clockwise and pulling away from the central
filter (Fig.6/4).
Fig.6/4
6
4. Gently tap the filter against the side of a
rubbish bin to remove excess dirt.
5. The central filter can be washed in warm water
[max 40(C]. Allow to air dry completely before
replacing.
NOTE: Do NOT use any detergents or boiling
water to wash the filter. Vax recommends washing
the filter every time you empty the dust container.
6. Return the central filter to the filter shroud and
rotate clockwise to secure.
7. Replace the central filter unit to the dirt
container ensuring the filter safety catch has
been reset.
8. Replace the dirt container as directed.
Post-motor Filter
NOTE: This is located on the right hand side of the
vacuum cleaner.
1. Release the post-motor cover and remove the
filter by pressing in the catch on the left hand
side.
2. The post-motor filter can be washed in warm
water [max 40(C]. Allow to air dry for 24 hours
before replacing.
NOTE: Do NOT use any detergents or boiling
water to wash the filter. Vax recommends washing
the filter every 9-12 months.
3. Replace the post-motor filter and cover before
re-starting the vacuum cleaner.
7. Cleaning Blockages
WARNING: To reduce the risk of electric shock,
the power cord must be disconnected before
performing maintenance/troubleshooting checks.
1. Turn the vacuum cleaner off and unplug from
the electrical outlet.
2. The flexible hose and X-tend (Model: V-091X
only) can be disconnected from the vacuum
cleaner by pushing in the button on the hose
and pulling away from the machine. Remove
any blockages found then reconnect the hose
securely.
8. Storage
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet and rewind the power cord
as directed before storing.
NOTE: Always store the vacuum cleaner base
down.
9. Troubleshooting
WARNING: To reduce the risk of personal injury, unplug the vacuum cleaner before performing
maintenance/troubleshooting checks.
PROBLEM: Vacuum cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in securely.
Cause: No electricity in the electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to 'on'.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner. Leave for one (1) hour before switching the
vacuum cleaner back on.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won't pick up/loss of suction.
Cause: Dirt container not installed properly.
Solution: Review dirt container replacement.
Cause: Dirt container full or blocked.
Solution: Empty dirt container.
Cause: Clogged filters.
Solution: Remove, clean and replace filters.
PROBLEM: Accessories won't pick up.
Cause: Accessories are not attached correctly.
Solution: Refer to section 5.
PROBLEM: Dust escaping from the vacuum cleaner.
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Dirt container not installed correctly.
Solution: Review dirt container replacement.
Cause: Hose/X-tend (Model: V-091X only) not installed correctly.
Solution: Review installation.
Cause: Filter not installed completely.
Solution: Remove, clean and replace filters.
10. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone will be available out of these
hours. Any queries or concerns about using your
Vax, call the Vax Careline. Calls are charged at the
UK national rate.
Please make a not of the model number and serial
number of your Vax before calling. There are over
400 approved Vax Service Agents in the UK. For
the nearest Vax Service Agent, please call the Vax
Careline or visit www.vax.co.uk
www.vax.co.uk
Troubleshooting / UK Service & Help / Technical Specification
11. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 2200W-2400W (dependant on
model)
Capacity: 3 litres approx
Filters: Washable central HEPA filter [with
filter shroud]
Post-motor filter
Cord length: 5.5m (approx)
Weight: 7.5kg
Subject to technical change
without notice.
7