Charter UR4U-MDVR-CHD2 Operating Instructions

1
Introduction
Operating Instructions
This remote control is designed to operate all
For 4-Function
Motorola and Scientific Atlanta digital set top
boxes (including HD and DVR), plus the
Cable Remote Control
majority of TVs, DVDs and AUDIO equipment
on the market as shown below.
CABLE : Cable Converters
DVD : DVDs, TV/DVDs
UR4U-MDVR-CHD2
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate this remote
control, you must first install two new AA Alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
Operations
DEFAULT STATUS:
Component Default: CABLE
Channel Default: CABLE channel +/- and
numbers operate through the CABLE box.
You have the option of controlling channel +/-
and numbers through the TV or DVD. Refer to
section G for programming steps.
Volume Default: CABLE volume +/- and mute
operate through the TV. You have the option
Universal Remote Control, Inc.
of controlling volume through the Cable box
or DVD. Refer to section H for programming
www.universalremote.com
OCE-0053A REV 31 (05/22/15) steps.
4
Button Functions
F
TV : Televisions
5
Programming the Remote Control
There are three ways you can program your remote control:
* Quick Setup Method
* 3-Digit Code Method
* Auto Search Method
Quick Setup Method is a unique feature that enables the fastest and easiest setup by using a one digit
code. This is the quickest way to set up devices made by popular manufacturers.
3-Digit Code Method allows you to setup by entering 3-digit code numbers that correspond to a
particular Component's manufacturer/brand, so it's the fastest and easiest of the two methods. (Code
Tables are on the backside of this Instruction Sheet.)
Auto Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTES:
This pertains to all programming steps. When you are in setup mode in each component, a component
LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off
and exit setup mode and you will need to start over.
When programming a combo unit, program as a DVD first.
A. Quick Setup Method
It's easy to program the remote control to
operate your TV. Simply press the number
buttons 0 through 9 that your TV brand is
assigned to using the following four steps.
STEP1 Manually turn on the TV you wish to
program.
STEP2 Press and hold simultaneously for 3
seconds both the TV and A (Yellow)
buttons or B (Blue) buttons, based on
the column your TV brand is assigned
to. The TV button LED light will turn on
for 30 seconds confirming that you are
in the program mode.
STEP3 While the TV button LED is on, point the
remote control at the TV and press the
number button assigned to your TV
brand as shown in the table (e.g. for
Sharp TV, button 5 ). The TV should turn
off. If it does not, press the same
number button repeatedly until the TV
turns off.
*Note : The remote will exit the programming
mode automatically if it does not have
matching codes and the LED will turn off.
TRANSPORT KEYS
STEP4 Once the TV has turned off, press the TV
button once again to save the code. The
remote control is now ready to control
your TV.
Repeat the above steps for all other components
(TV, DVD, etc.)
*Note : If the matching code could not be found
in STEP3, use 3-Digit Code Method or
Auto Search Method.
Quick Set-up Code Tables
TV
Button Press Button Number Brand
0 RCA
1 SAMSUNG
2 SONY
3 LG
TV&A
4 VIZIO
5 SHARP
Button
6 PANASONIC
7 SANYO
8 TOSHIBA
9 PHILIPS
0 COBY
1 MITSUBISHI
2 HITACHI
3 MAGNAVOX
TV&B
4 JVC
5 ZENITH
Button
6 INSIGNIA
7 EMERSON
8 WESTINGHOUSE
9 TCL
DVD
Now, program the rest of your Components by
repeating STEPS 1-5.
Button Press Button Number Brand
0 HITACHI *Note : If the Pre-Programmed Method did
1 SONY not work, or if the Code Tables do not
list your Component brand, use the
2 PHILIPS
Auto Search Method as explained in
3 SAMSUNG
DVD&A Section C.
4 PHILIPS MAGNAVOX
5 PANASONIC
Button
C. Auto Search Method
6 LG
7 JVC
STEP1 Turn on the Component you want to
8 DENON
program (TV, DVD or AUX).
9 PIONEER
STEP2 Press the [COMPONENT] button (TV,
AUX
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
Button Press Button Number Brand
seconds. The Component LED will light
0 BOSE for 30 seconds indicating the unit is
1 HP ready to be programmed.
2 ONKYO
STEP3 Point the remote toward the
3 APPLE / iPod
Component and press the [CH5] or
AUX&A 4 MICROSOFT / XBOX
[CH6] button one step at a time or
5 SONY / PS2
Button
keep it pressed. The remote will emit a
6 LUTRON
series of ON/OFF commands. Release
7 X-10
the [CH5] or [CH6] button as soon as
8 YAMAHA
the Component turns Off.
9 ROKU
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section B). If any
B. 3-Digit Code Method
of the functions do not work as they
STEP1 Turn on the Component you want to should, repeat from STEP 3 using [CH5]
program (TV, DVD or AUX) . or [CH6] buttons to find the correct code.
STEP2 Press the [COMPONENT] button (TV, STEP5 Save the code. (Same as for 3-Digit Code
DVD or AUX) to be programmed and Programming Method - Section B).
[OK/SEL] button simultaneously for 3
Now, repeat the Auto Search Method for those
seconds. The Component LED will light
Components you could not program earlier with the
for 30 seconds indicating the unit is
Pre-Programmed Method.
ready to be programmed.
STEP3 Point the remote control toward the
D. Finding a Component Button's
Component and enter the 3-digit code
Setup Code Number
number assigned to your brand.
If you used the Auto Search Method to program a
*Note : If the 3-digit code number you just
Component, you may not know what the correct code
entered is correct, the Component will
number is. Here is a way for you to identify the code
turn Off. If it did not turn Off, continue
number, so you can record it for future reference.
entering code numbers listed for that
brand until the Component turns Off.
STEP1 Press the [COMPONENT] button (TV, DVD or
AUX) you want to verify and the [OK/SEL]
STEP4 After you've entered the correct code
button simultaneously for 3 seconds. The
number and the Component has turned
Component LED will light for 30 seconds.
Off, press the [POWER] button to turn
the Component back On. Now it's time STEP2 Press the [INFO] button and count the
number of times the Component LED light
to test the VOLUME and MUTE buttons
blinks. This number indicates the first digit
for the TV (or PLAY and STOP buttons
of the code, followed by the second and
for DVD) to make sure they all work. If
third, each separated by a one second
any of the functions do not work as
pause when the LED will turn off.
they should, repeat from STEP 3 using
the next 3-digit code number listed for
*Note : 10 blinks represents the number zero.
that brand.
Example : One blink, (pause), eight blinks, (pause) and
STEP5 Once you have found the correct 3-
three blinks, indicates code number 183.
digit code, save it by pressing the same
[COMPONENT] button one more time.
E. AUX Function: Programming a 4
The Component LED light will blink
Component
twice to confirm that the code was
successfully stored.
You can take advantage of the AUX function to
program a 4 th Component such as a second TV, DVD
or Audio Component.
STEP1 Turn on the 4 th Component you want to
program (TV, DVD or Audio).
STEP2 Press the [AUX] button and the [OK/SEL]
button simultaneously for 3 seconds.The
[AUX] Component LED will light for 30
seconds.
STEP3 Press the [COMPONENT] button you want to
setup. Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just entered is
the correct number, the Component will turn
Off. If it did not turn Off, continue entering
code numbers listed for that brand until the
Component turns Off.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section B). If
any of the functions do not work as they
should, you need to find a new code.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The Component LED light
will blink twice to confirm the code was
stored. Now when you press the AUX
button, all the buttons will work with that 4 th
Component.
F. Programming the System On/Off Button
This allows you to program the System On/Off button
so it can send up to four power On/Off commands
with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED will
light for 30 seconds.
STEP3 Press the first [COMPONENT] button you
want to store in the [SYSTEM ON/OFF]
button and then the [POWER] button.
Repeat this for other Components until you
have stored all the desired power
commands into the [SYSTEM ON/OFF]
button.
STEP4 Press the [CH5] button to save the power
commands you stored. The [CBL] button
will blink twice to confirm the commands
have been saved.
G. Programming Channel Control
You can program the channel controls (Channel Up,
Channel Down, Last and Numbers) from one
Component to operate in another Component mode.
Default channel control settings on the remote control
are as follows:
th
CBL : CBL T V : CBL
DVD : DVD AUX : AUX