Table of Contents
Related Manuals for Essilor Neptune Mini
Summary of Contents for Essilor Neptune Mini
- Page 1 Mini Water Filtering System User Manual V1.2_13/06/2014 Essilor International (Compagnie Générale d'Optique) S.A. Siège Social : 147, rue de Paris – 94227 Charenton-le-Pont Cedex France 712 049 618 RCS Créteil - www.essilor.com...
- Page 2 User Manual - Neptune Mini Filtering System ______________________________________________________________________________ V 1.2 - 2 -...
-
Page 3: Safety Instructions
User Manual - Neptune Mini Filtering System Safety instructions Intended application • This device has been developed for the filtration of the water used to edge ophthalmic lenses. Do not use it for any other reason. General Safety • Before putting the device into operation please read the safety instructions and the operation manual carefully. -
Page 4: Operating Principle
User Manual - Neptune Mini Filtering System Operating Principle The operating principle of the system is simple. The edger cooling water is contained in the back tank of the Neptune filtration unit. These 25 litres of polluted water during the day by edging residues are pumped into the front tank of the system when starting the filtration cycle. - Page 5 User Manual - Neptune Mini Filtering System Starting to use the Neptune filtering system Unpack Neptune and remove all the polystyrene packaging Check correct positioning of the 2 pumps. 1 Return pump 2 Main pump 3. Introduce the PVC grey wall into the dedicated slides.
- Page 6 User Manual - Neptune Mini Filtering System 7. Connect the cleaning hydraulic circuit to the vertical tube of the return right pump. See photo. Position the cover of the tank with the filtering bag. Check that the bag is well open and "sticks" to the walls.
- Page 7 User Manual - Neptune Mini Filtering System 13. Connect the control unit, • Run the cable through a hole in the work bench • Connect the cable to the box • Place the box next to the edger 14. Connect Neptune to the mains.
-
Page 8: Control Unit
User Manual - Neptune Mini Filtering System Description Control Unit 1. DAY mode switch and green LED indicator 2. NIGHT mode switch and red LED indicator 3. Inverter switch DAY/NIGHT 4. Filtering tank water presence green LED indicator (T2) 5. Water level LED indicator in working tank (T1) MIN - OK - MAX 6. - Page 9 User Manual - Neptune Mini Filtering System Filtration Cycle start In the evening • Move the handle to the left position - Night. This operation is essential to filter the water and clean the water receiver. • Press the MODE switch every evening when closing the lab.
- Page 10 User Manual - Neptune Mini Filtering System Control box display The cycle counter indicates the number of cycles that took place in 60 minutes with a maximum of 10 cycles.. When the filtering cycle is finished, a number from 0 to 9 or a letter P or G will be shown: The counter indicates 3 or below, it is time to change the filtering bag.
- Page 11 User Manual - Neptune Mini Filtering System Delayed start of the filtration cycle 1. To enter the programming mode, hold down the MODE switch (approx 2s.) until the LED counter blinks. It shows the number of hours for the delayed start of the filtration cycle.
-
Page 12: Maintenance
User Manual - Neptune Mini Filtering System Maintenance Changing the filtering bag The bag has to be changed every 1200 lenses on average. Do not clean it ! When the cycle counter indicates 3 or less, the filtering bag has to be changed within a few days, i.e. - Page 13 User Manual - Neptune Mini Filtering System Changing the water In order to maintain the best performance of the filtering system, it is recommended to drain the water at least once a year. Depending of the nature of the water and the amount of edged lenses, it might be necessary to perform this operation more often.
- Page 14 User Manual - Neptune Mini Filtering System Pumps and sensors tests All components of Neptune can be individually tested to diagnose a possible breakdown • Filtration tank bottom sensor – Sensor N°1 This sensor indicates the presence of water in the filtering tank.
- Page 15 User Manual - Neptune Mini Filtering System TEST Mode - Main pump and return pump Their correct operation can be checked: Press the MODE button to switch to DAY mode Start the cycle by pressing the RUN button until the corresponding red LED lights (min 3 sec.)
- Page 16 User Manual - Neptune Mini Filtering System Answers to frequently asked questions (FAQ) Filtration (night) cycle does not start The starting of the night cycle is controlled by the RUN button and the signal "presence of water" in the work tank emitted by the water level sensor N°3 located at the bottom of the tank.
- Page 17 User Manual - Neptune Mini Filtering System Accessing to the electrical box and fuses Unplug the electrical plug from the socket. Unscrew the 2 screws on the front panel. Remove the cover. Unscrew the 4 screws of the electrical box.
- Page 18 User Manual - Neptune Mini Filtering System Main Board Version 3 Control panel V3 (Filtering cycle counter) Anti-smell electric board This product is compliant with marking. PRISME 3, sente à l'ane 27600 Saint Pierre la Garenne - FRANCE ______________________________________________________________________________ V 1.2...
Need help?
Do you have a question about the Neptune Mini and is the answer not in the manual?
Questions and answers