Sanyo EM-S100 Service Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Microwave Oven
  5. EM-S100
  6. Service manual
Sanyo EM-S100 Service Manual

Sanyo EM-S100 Service Manual

Hide thumbs Also See for EM-S100:
Table of Contents

Advertisement

Quick Links

See also: Service Manual Supplement
SERVICE MANUAL

WARNING TO SERVICE TECHNICIANS

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING
SERVICING TO AVOID POSSIBLE EXPOSURE TO
(a)
Do not operate or allow the oven to be operated with the door open.
(b)
Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave
source, and make repairs as necessary:
(1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage),
(4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c)
Before turning on microwave power for any service test or inspection within the microwave generating compartments,
check the magnetron, wave guide transmission line, and cavity for proper alignment, integrity, and connections.
(d)
Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmis-
-sion systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is
released to the owner.
(e)
A microwave leakage check to verify compliance with the Federal performance standard should be performed on each
(i)
oven prior to release to the owner. For U.S.A.
(e)
A microwave leakage check to verify compliance with the Canadian Regulation, HEALTH AND WELFARE,
(ii)
SOR/79-920 should be performed on each oven prior to release to the owner. For CANADA
Microwave Oven
CAUTION

EXCESSIVE MICROWAVE ENERGY

File No:
EM-S100
Product Code No:
437 436 05
REFERENCE NO. SM - 860235

Advertisement

Table of Contents
loading

Related Manuals for Sanyo EM-S100

Summary of Contents for Sanyo EM-S100

  • Page 1: Warning To Service Technicians

    File No: SERVICE MANUAL EM-S100 Microwave Oven Product Code No: 437 436 05 CAUTION WARNING TO SERVICE TECHNICIANS PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY Do not operate or allow the oven to be operated with the door open.

  • Page 4: Specifications

    2. SPECIFICATIONS 4. PRECAUTIONS AND REPAIR SERVICE TIPS PRELIMINARY Rated Power Consumption . . . 1600W SINCE NEARLY 2,000 VOLTS EXISTS IN SOME Microwave Output ..1000W CIRCUITS OF THIS MICROWAVE OVEN, REPAIRS Frequency .

  • Page 5: Circuit Diagram

    5. CIRCUIT DIAGRAM NOTE : All component have special characteristics for safety and must be replaced using parts listed in this manual. All service on M/W ovens should be performed by a qualified technician using approved testing equipment. Customers should not attempt replace component marked with a symbol.

  • Page 6: Test Procedures And Troubleshooting

    6. TEST PROCEDURES AND TROUBLESHOOTING...
  • Page 13 7. DISASSEMBLY INSTRUCTIONS...

  • Page 17: Exploded View And Parts List

    8. EXPLODED VIEW AND PARTS LIST CAVITY PARTS NOTE : All component have special characteristics for safety and must be replaced using parts listed in this manual. All service on M/W ovens should be performed by a qualified technician using approved testing equipment. symbol.
  • Page 18 SWITCHES AND MICROWAVE PARTS NOTE : All component have special characteristics for safety and must be replaced using parts listed in this manual. All service on M/W ovens should be performed by a qualified technician using approved testing equipment. Customers should not attempt replace component marked with a symbol.

  • Page 19: Door Parts

    DOOR PARTS NOTE : All component have special characteristics for safety and must be replaced using parts listed in this manual. All service on M/W ovens should be performed by a qualified technician using approved testing equipment. Customers should not attempt replace component marked with a symbol.

  • Page 20: Control Panel Parts

    CONTROL PANEL PARTS NOTE : All component have special characteristics for safety and must be replaced using parts listed in this manual. All service on M/W ovens should be performed by a qualified technician using approved testing equipment. Customers should attempt replace component...

  • Page 21: Control Circuit Board

    CONTROL CIRCUIT BOARD (Part No.617 206 7964)

  • Page 22: Overall Circuit Diagram

    9. OVERALL CIRCUIT DIAGRAM...
  • Page 23 MAY ‘99 LT 300 Printed in Singapore...

Table of Contents