Table of Contents
Advertisement
Quick Links
IP Camera Instruction Manual
Chapter 1
............... Product Introduction
Chapter 2
..................Product Installation
Chapter 3 .................. Search equipment
Chapter
4.....................
(Pan/Tilt/Zoom) control operations
Chapter 5
............... System Settings options
Chapter 6
.................. Network settings
Chapter 7 .................. System Tools
Chapter 8 ..................
WIFI Model No: IP-302-B
Video
Logout
attribute
settings
and
PTZ
Advertisement
Table of Contents
Summary of Contents for Polaroid IP-302-B
- Page 1 IP Camera Instruction Manual WIFI Model No: IP-302-B Chapter 1 …………… Product Introduction Chapter 2 ………………Product Installation Chapter 3 ……………… Search equipment Chapter 4………………… Video attribute settings (Pan/Tilt/Zoom) control operations Chapter 5 …………… System Settings options Chapter 6 ……………… Network settings Chapter 7 ………………...
-
Page 2: Chapter 1 Product Introduction
Chapter 1 Product Introduction 1.1 Hardware/Software requirements: To use the computer-camera through networks, the minimum hardware requirements of your computer should be met, 1. Pentium III CPU or better, 1GHz or higher frequency; 2. At least 256M memory; 3. windows xp, 2000 operating system or above Internet explorer 4.0 browser or above version, IE 6.0 is strongly recommended. -
Page 3: Chapter 2 Installation
can be authorized to different permission levels to operate the network camera. Chapter 2 installation 2.1 Hardware installation 1. Connect the network: Connect the networking camera to the router or switch. 2. Connect the power Connect the networking camera with power. Cautions: Please use the original power adaptor along with the camera;... - Page 4 used in case that installation CD is not available. Chapter III Search equipment and log in to the network camera 1: Make sure the equipment is properly connected with the network and power. 2: The router must support DHCP (Dynamic Host Configuration Protocol), because dynamic IP addresses obtaining is one of the factory settings of camera.
- Page 5 to access the login page (for example: http://192.168.1.92). As shown 3: user name and password authentication the default user name and password are both “admin”. For the first login, enter your user name (admin), password (admin) and click on the "Login" button to enter the monitor interface, the user name and password are modifiable.
-
Page 6: Chapter 3 Video Attribute Settings And Ptz(Pan/Tilt/Zoom)
Chapter 3 Video attribute settings and PTZ(Pan/Tilt/Zoom) control operations 4.1 Function Description: Window: the window is defined as video window number shown in the video region ,the current maximum of which were 36. Resolution: the size of the currently selected video. Currently supports two sizes: 640x480 and 320x240. - Page 7 Mute: Check to close/open audio. OSD, OSD color: Display the date/time and the color when displaying. Connection: When the video camera window specifies IP address, click on this button and video from the connected camera will be displayed. In the opening pages of video surveillance, it will automatically connect the camera and video will come.
-
Page 8: Chapter V System Settings Options
Chapter V System Settings Options Network camera page setup options are in the far left, when clicking the left arrow, the hidden settings page will be expanded. Click the left arrow, set the options as follows Functional description of the set-up options: 1: video monitor For viewing video, in any case you can click on this button to enter the video mode to watch. - Page 9 Note: The device name can be changed: 1, User can customize the name of the device in order to distinguish different equipments. 2, When the video surveillance equipment connected, the page will show the device and the name. 3, The search tool can also display the searched device names. 3: Net config: set up network-related parameters.
- Page 10 3.2: WiFi config 1, the device supports WiFi wireless capabilities. If user’s camera supports wireless networking functions. After setting up WiFi parameters, such as Password, Authentication parameters, please select "Enable" and restart the device. Then, the user will be able to access the network through a wireless network of cameras.
- Page 11 3.3: Dynamic DNS This equipment support dynamic DNS of Www.3322.org and www.dyndns.org. Enter the applied dynamic domain name, user name, password, and click “Save” to access device through WAN. 3.4: upnp settings Upnp is to realize automatic port mapping function. If the camera is connected to a router, In order to access to the cameras through WAN, it is required to open a specified port of the router to the camera.
-
Page 12: Chapter Vi Alarm Settings
WAN, in order to distinguish different cameras, each camera needs a different port, such as 81, 82, etc. and so on. Chapter VI alarm settings Alarm camera settings are used to set the alarm function of network camera. When external alarm signal is triggered, alarm will come. The alarm device can be high sound alarm device or sound &light alarms device. - Page 13 IO Alarm Enable or disable IO alarm at this page. SMTP config Provide email sender information here, which is need for send email when motion detects or other alarm is occurring.
- Page 14 FTP config Fill FTP information here, which is need to upload images to FTP server. Chapter VII of the System Tools Restart the equipment When settings changes happen, it is required to restart your device to the changes to take effect, you can click on the page "Reboot Device" to enable the device to restart.
-
Page 15: User Management
7.2 to restore the factory settings Click "reset configt" will enable the device to restore all settings to factory default, the default user name and password are both “admin”. Note: The factory default settings using DHCP to obtain IP address. After restoring the factory settings, device IP address may be different from the one before restoration. - Page 16 The following are the Edit and Modify interface: Users can be enabled or disabled. The disabled users can’t log on equipment page. Description: user "admin" is the super-administrator user, who can set up and operate all the functionalities of all the networking cameras. 7.4 Multiple Devices Manager In this page, not only the main video, but also additional device can be connected be automatically.
-
Page 17: Local Configuration
the video surveillance page. Additional equipment can be disabled, and the disabled device will not appear in the video surveillance page The next figure describe how to add/edit the additional device. 7.5 Local configuration To set video recording and photographing saving directory, it is required to input save path in "captured photo file"... - Page 18 7.6 Download Ocx control Clicking on the link in this page is available for download ocx control. 7.7 Update Software Updating software is to enable users to use the latest software. The upgrade file name is app.bin, Click button "Browse" to find out the path where app.bin is stored.
- Page 19 7.8 update the webpages Updating web page is mainly to upgrade the appearance of web pages, file name for upgrading www.bin, Click button "Browse" to find out the path where www.bin is stored. You can click to upgrade, the system will show the upgrading files progress, success information will be prompted if upgrading successfully.
- Page 20 Logging out from the current registry, it will return to the login page. Login must be accomplished again if the user wants to operate the equipment again.
Need help?
Do you have a question about the IP-302-B and is the answer not in the manual?
Questions and answers