Se Ekt Key Patterns - Panasonic Strata Se General Description Manual

PROGRAMMING PROCEDURES
SECTION 500-036-300
JANUARY 1988
7) Mark an X next to 00 if the telephone or de-
vice connected to the HIOB is to have pri-
vacy. Leave blank if privacy is not required.
4XX Program- Station Type Assignment
NOTE.
When programming,
always
do
Program
4XX
before
Program 4#XX. lf Program 4XX
is programmed after 4#XX, the stations' flex-
ible key assignments will be reset to the de-
fault data.
Informs the system of the EKT type being
used at each station and the order of CO line
appearance. The selections listed below are se-
parated into two sections, Se first and Vle se-
cond, and must be repeated for each station. In
all cases, mark an X where required.
"STRATA Se only-see Figure 2.
1) Mark an X next to 09 if the CO lines are to
be assigned from top to bottom (descending
order). If 09 is left blank, CO lines are as-
signed bottom to top (ascending order).
2) Mark Xs next to 05 and 01 if keystrip pattern
D is desired.
3) Mark Xs next to 06 and 01 if keystrip pattern
C is desired.
4) Mark Xs next to 06 and 00 if keystrip pattern
B is desired.
5) Mark Xs next to 05 and 00 if keystrip pattern
A is desired.
6) Mark an X next to 03 if
a
single-line EKT
(with or without MW LED) is equipped.
7) Mark an X next to 01 if a lo-key EKT or sin-
gle line with MW LED is equipped.
- 8) Mark an X next to 00 if
a
20-key EKT is
equipped.
NOTE.
The upper ten keys in keystrips A,
B may be
programmed
for other features.
"STRA TA Via only-see Figure 3.
1) Mark
an X next to 11 if you want the first
CO line number to be CO4 (location depends
on the selection at 09).
2) Mark
an X next to 10 if you want the first
CO line number to be CO1 (location depends
on the selection at 09).
-12-
3) Mark an X next to 09 if the CO lines are to
be assigned from top to bottom (descending
order). If 09 is left blank, CO lines are as-
signed bottom to top (ascending order).
4) Mark an X next to 07 if 20-key pattern C is
desired.
5) Mark an X next to 06 if 20-key pattern B is
desired.
6) Mark an X next to 05 if 20-key pattern A is
desired.
7) Mark an X next to 03 if a single-line EKT is
equipped.
8) Mark an X next to 01 if
a
lo-key EKT is
equipped.
9) Mark an X next to 00 if a 20-key EKT is
equipped.
A
MW/FL
DND
-
-
-
-
co3
co2
co1
INT
BLF
BLF
BLE
BLF
BLF
BLF
BLF
BLF
BLF
BLF
6
MW/FL
DND
-
-
-
-
co3
co2
co1
INT
D
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
MW/FL
DND
AD4
AD3
AD2
AD1
co3
co2
co1
INT
BLF
BLF
BLF
BLF
BLF
BLF
BLF
BLF
BLF
BLF
FIGURE 2-Se EKT KEY PATTERNS
4#XX Program-Station
Flexible Key Assign-
ments
NOTE:
Do this after
Program 4XX.