Table of Contents
Advertisement
Owners Manual
Project Series Paint Sprayers
Important Safety Instructions
Read all warnings and instructions in this manual and on the
unit, including the power cord. Be familiar with the controls and
the proper usage of the equipment. Save these instructions.
WARNING
Use only water-based materials. Do not
use materials which state "FLAMMABLE"
on the packaging. For more information
about your material, request SDS from
distributor or retailer.
For portable spray applications of water-based architectural paints and coatings only.
Not approved for use in explosive atmospheres or hazardous locations.
For Household Use Only.
334179B
Scan QR code or click on link
for operational video.
http://graco.com/tc360opvid
ti24623a
EN
ti26063a
Advertisement
Table of Contents
Related Manuals for Graco TrueCoat 360 16Y391
Summary of Contents for Graco TrueCoat 360 16Y391
-
Page 1: Important Safety Instructions
Be familiar with the controls and the proper usage of the equipment. Save these instructions. Scan QR code or click on link for operational video. http://graco.com/tc360opvid ti24623a WARNING Use only water-based materials. Do not use materials which state “FLAMMABLE”... -
Page 2: Table Of Contents
Graco Limited Warranty ........ -
Page 3: Important User Information
Before using your sprayer read this Owners Manual for complete instructions on proper use and safety warnings. Congratulations! You have purchased a high-quality paint sprayer made by Graco Inc. This sprayer is designed to provide superior spray performance with water-based architectural paints and coatings. -
Page 4: General Power Tool Safety Information
General Power Tool Safety Information General Power Tool Safety Information WARNING WARNING Personal Safety Read all safety warnings and all instructions. • Stay alert, watch what you are doing and use common sense when operating Failure to follow the warnings and instructions a power tool. - Page 5 General Power Tool Safety Information WARNING Power Tool Use and Care • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Page 6: Sprayer Safety Information
Sprayer Safety Information Sprayer Safety Information The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. - Page 7 Sprayer Safety Information WARNING WARNING FIRE AND EXPLOSION SKIN INJECTION HAZARD HAZARD High-pressure spray is able to inject toxins into the body and Flammable fumes, such as cause serious bodily injury. In solvent and paint fumes, in work the event that injection occurs, area can ignite or explode.
- Page 8 Sprayer Safety Information WARNING WARNING ELECTRIC SHOCK HAZARD PRESSURIZED ALUMINUM PARTS HAZARD This equipment must be grounded. Improper grounding, setup, or usage Use of fluids that are incompatible of the system can cause electric with aluminum in pressurized shock. equipment can cause serious chemical reaction and equipment •...
-
Page 9: Component Identification
Component Identification Component Identification Prime Pump Spray ti26060a Sprayer Trigger Cup Cover Dual Speed Control, HIGH/LOW FlexLiner Switch (DS and DSP models only) Cup Support Spray Tip, Black (12-inch pattern) VacuValve Cap Spray Tip, Gray (4-inch pattern) VacuValve Air Hole Spray Tip Guard VacuValve Reservoir Variable Speed Control (VSP models... -
Page 10: Start Up
Start Up Start Up Fill FlexLiner with material. Securely tighten cup cover onto cup support. Tighten so the arrow on the cup cover is within range of the indicator on the cup support. Use only water-based materials. Do not use materials which state “FLAMMABLE” on the packaging. - Page 11 Start Up The VacuValve is an important part of Plug sprayer into power source. your new sprayer. It is used to evacuate Turn Prime Pump/Spray knob down to the air out of the FlexLiner. Open Prime Pump position. To fill sprayer with VacuValve cap.
-
Page 12: Refilling Flexliner
Start Up 10. Make certain spray tip is in the spray • Make certain the Prime Pump/Spray position. knob is in the Spray position. Spray SPRAY UNCLOG ti23290a 11. You are now ready to spray. ti23288a NOTE: For best results; to evacuate all material from the FlexLiner when the material •... -
Page 13: How To Spray
How to Spray How to Spray Spray Techniques Take a few moments prior to spraying and review these simple tips to ensure your spraying project is a success. Use a piece of scrap cardboard to practice these basic spraying techniques before you Dual Speed Control begin spraying the surface. -
Page 14: Triggering Sprayer
How to Spray EVEN FINISH ti23376a Aiming Sprayer Aim sprayer at bottom edge of previous stroke, overlapping each stroke by half. THIN THICK THIN ti23375a Triggering Sprayer Pull trigger after starting stroke. Release ti23378a trigger before end of stroke. Sprayer must be moving when trigger is pulled and released. -
Page 15: Spray Pattern Quality
How to Spray Spray Pattern Quality If you see pulsations in the pattern, try the following; A good spray pattern is evenly distributed as • On the dual speed models turn the dual it hits the surface. If tails persist, material may speed control to HIGH need to be thinned. -
Page 16: Cleanup
Cleanup Cleanup Disconnect power (unplug power cord). Turn Prime Pump/Spray Knob down to PRIME PUMP position to relieve pressure. Use only water-based materials. Do not use materials which state “FLAMMABLE” on the packaging. For more information Prime Pump about your material, request SDS from distributor or retailer. - Page 17 Cleanup Set the sprayer upside down on a flat Make certain the Prime Pump/Spray surface. This will keep the wet paint in knob is in the Prime Pump position the cup cover. Return excess material to (pointed down). On models with a dual original container.
-
Page 18: Cleaning Vacuvalve
Cleanup 16. Use a soft cloth to clean the cup support and cup cover. ti23372a NOTICE ti23389a The spray tip guard is permanently 13. Remove cup assembly and discard used attached to the sprayer. Removal for fluid. Dispose of used cleaning fluid cleaning is not necessary and will result in properly. -
Page 19: Storage
Storage Storage NOTICE Failure to store sprayer with Pump Armor will result in operational problems the next time you spray. Always circulate Pump Armor through the sprayer after cleaning. Water left in the sprayer will corrode and damage the pump. ti23707b Pump Armor fluid protects the sprayer while in storage. -
Page 20: Common Procedures
Common Procedures Common Procedures Installing Spray Tips Pull the spray tip straight out of the spray tip guard. Install Spray Tip While holding the spray tip 90 degrees from either the SPRAY or UNCLOG Do not put your hand in front of the spray position, align spray tip locking tab with tip. -
Page 21: Unclogging Spray Tip
Common Procedures Unclogging Spray Tip In the event that particles or debris clog the spray tip, this sprayer is designed with a ti23359a reversible spray tip that quickly and easily clears the particles without disassembling the Variable speed models: sprayer. Set speed control to 10. -
Page 22: Flushing A New Sprayer
Common Procedures Flushing a New Sprayer This sprayer arrives from the factory with a small amount of test material in the system. It is important that you flush this material from the sprayer before using it for the first time. Remove cup assembly from the sprayer by turning counter clockwise and pulling down. - Page 23 Common Procedures Align VacuValve on cup cover with Prime Pump/Spray knob. Push cup assembly onto sprayer and twist to lock. ti23258b ti23389a 11. While holding the sprayer upside down Plug sprayer into power source. point the sprayer into a waste pail. Pull Make certain the Prime Pump/Spray the trigger for three seconds.
-
Page 24: Replacement Parts
Replacement Parts Replacement Parts Models 16Y391, 16Y392 ti24627a ti23568a 334179B... -
Page 25: Parts List- Models 16Y391, 16Y392
Replacement Parts Parts List- Models 16Y391, 16Y392 Order If you have this Ref. Part Description model sprayer Number Kit, pump 16Y391 17A217 Complete pump assembly includes 2, 3, 4, 5, 6, 7, 8 16Y391 17A218 Pump housing includes 2, 3, 5 16Y392 17B415 Complete pump assembly includes 2, 3, 4, 5, 6, 7, 8 16Y392... -
Page 26: Replacement Parts
Replacement Parts Replacement Parts Model 17F329 ti26108a 334179B... -
Page 27: Parts List- Model 17F329
Replacement Parts Parts List- Model 17F329 Order If you have this Ref. Part Description model sprayer Number Kit, pump 17F329 17B415 Complete pump assembly includes 2, 3, 4, 5, 6, 7, 8 17F329 17B416 Pump housing includes 2, 3, 5 All models 16Y425 O-ring All models... -
Page 28: Troubleshooting
Troubleshooting Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. ti26063a Sprayer Diagnostics Problem Cause Solution Sprayer makes no sound Power supply. Verify power to sprayer. when trigger is pulled Motor has overheated. Wait 20-30 minutes for motor to cool. - Page 29 Troubleshooting Problem Cause Solution Speed control switch is set too low. On models with a dual speed Sprayer makes sound control switch, set speed control but no material is switch to HIGH. On variable sprayed when trigger is speed models, increase speed pulled (contd) until unit sprays.
- Page 30 Troubleshooting Spray Pattern Diagnostics Problem Cause Solution Spray pattern is pulsating: Operator is moving too Slow speed of movement. fast while spraying. Spray tip is clogged. Unclog spray tip or clean spray tip see Unclogging Spray Tip, page 21. Material difficult to On models with dual speed atomize.
- Page 31 Troubleshooting Problem Cause Solution Spray pattern is too narrow: Sprayer is too close to Move sprayer away from target surface. surface 10 in. (25 cm) Incorrect spray tip for Install different size spray tip. application of material. See Installing Spray Tips, ti15523a page 20.
-
Page 32: Technical Data
Technical Data Technical Data Hand-Held Sprayer U.S. Metric Max Working Pressure TrueCoat 360 1200 psi 8.3 MPa, 83 bar TrueCoat 360 DS/DSP/VSP 1300 psi 9 MPa, 90 bar Maximum Amperage 1.2 Amps Weight TrueCoat 360, 360 DS/DSP 3.5 lb (18 in.cord) 1.6 kg (45 cm cord) TrueCoat 360 VSP 3.75 lb (18 in.cord) -
Page 33: Graco Limited Warranty
1-888-541-9788 or visit us online at www.graco.com. If the claimed defect is verified, Graco will repair or replace the product free of charge. The product will be returned to the original purchaser transportation prepaid. If inspection of the product does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge to you, which charges may include the costs of parts, labor and transportation. - Page 34 Original instructions. This manual contains English. MM 334179 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com...