Advertisement
Projector and lullaby
Find/page the parent unit
You can turn on the projector and lullaby on the
Use this feature to find misplaced parent units.
baby unit. The baby unit projects colorful images
1.
Press page on the baby unit. All idle parent
to the environment, and plays the lullaby to
units ring and display PAGING.
comfort your baby.
2.
To end paging, press any key on the parent
unit, or press page on the baby unit.
When the projector is turned on,
displays on the
parent unit screen. The baby unit will play lullaby.
NOTES
•
Press
once to turn on the projector and
•
Paging rings all parent units even if the speaker
play lullaby. The interesting and colorful
volume of parent unit is set to VOLUME OFF.
images is projected at the same time.
•
The baby unit cannot page any parent unit that is
•
Press
again to stop playing the lullaby.
turned off, out of range or talking to the baby unit.
The baby unit keeps projecting the colorful
images.
General product care
•
Press
for a third time to turn off the
projector. The interesting and colorful images
To keep this product working well and looking good,
fade out.
follow these guidelines:
•
Avoid putting it near heating appliances and devices
NOTES
that generate electrical noise (for example, motors
•
The projector and lullaby will automatically turn off
or fluorescent lamps).
after 15 minutes.
•
DO NOT expose it to direct sunlight or moisture.
•
We recommend you not to turn on the vibration
alert and the lullaby at the same time, as the
•
Avoid dropping the product or treating it roughly.
lullaby will trigger the vibration alert frequently.
•
Clean with a soft cloth.
•
If the baby unit receives talkback from the parent
•
DO NOT immerse the parent unit and the baby
unit during lullaby playback, the lullaby will be
unit in water and do not clean them under the tap.
paused. It resumes after the talkback finishes.
•
DO NOT use cleaning spray or liquid cleaners.
Talk to the baby unit
•
Make sure the baby unit and parent unit are dry
You can broadcast messages from a parent unit to
before you connect them to the mains again.
the baby unit and the other parent unit. If you have
two parent units, you can use both of them at the
Storage
same time to talk to the baby unit.
•
Press and hold talk on the side of the parent
When you are not going to use the baby monitor for
unit. The screen displays TALK when the
some time, remove the rechargeable battery from the
voice connection to the baby unit is made.
parent unit. Store the parent unit, the baby unit and
Speak towards the mic on the parent unit.
the adapters in a cool and dry place.
Your voice is broadcast to the baby unit and
the other parent unit.
NOTES
•
If the speaker volume of the parent unit is set
to VOLUME OFF, it will be reset to the default
VOLUME 3 when you press and hold TALK.
•
When a parent unit is talking to the baby unit, it is
also broadcast to the other parent unit. However,
sounds from the baby unit cannot be transmitted
to the parent units at the moment.
number only signifies that the Industry Canada
6.
MISE EN GARDE: Il peut y avoir un risque
technical specifications were met.
d'explosion si vous utilisez le mauvais type de
piles pour l'unité du parent. N'utilisez que le
This product meets the applicable Industry Canada
technical specifications.
bloc-piles rechargeable inclus ou le bloc-piles de
rechange (BT166342/BT266342). N'incinérez pas
RF radiation exposure statement
les piles. Celles-ci risqueraient d'exploser. Jetez
The baby unit complies with FCC RF radiation
les piles usées selon les renseignements suivant
exposure limits set forth for an uncontrolled
le sceau du RBRC
.
MD
environment. The baby unit should be installed and
7.
N'utilisez que les adaptateurs inclus avec ce
operated with a minimum distance of 8 in (20 cm)
produit. L'utilisation d'un adaptateur dont la
between the baby unit and all persons' body. Use of
polarité ou la tension serait inadéquate risque
other accessories may not ensure compliance with
d'endommager sérieusement le produit et mettre
FCC RF exposure guidelines. This transmitter must
votre sécurité en péril.
not be co-located or operating in conjunction with any
Adaptateur de l'unité du bébé: Entrée 100-120V
other antenna or transmitter. This equipment complies
CA 150 mA 60 Hz;
Sortie : 6 V CC 600 mA.
also with Industry Canada RSS-102 with respect to
Adaptateur de l'unité du parent: Entrée 100-120V
Canada's Health Code 6 for Exposure of Humans to
CA 150 mA 60 Hz;
Sortie : 6 V CC 400
RF Fields.
8.
Lorsqu'ils sont branchés dans une prise de
courant, les adaptateurs secteur ont été conçus
California Energy Commission
pour être orientés correctement, soit à la verticale
battery charging testing mode
ou au plancher. Les broches n'ont pas été conçues
pour supporter le poids du bloc d'alimentation et
le maintenir en place si celuici est branché dans
This baby monitor meets the California Energy
une prise au plafond, sous une table ou dans un
Commission (CEC) regulations for energy consumption.
meuble.
Your baby monitor is set up to comply with the energy-
9.
Pour les PRODUITS À BRANCHER À UNE
conserving standards right out of the box.
PRISE DE COURANT, la prise de courant doit
Follow the instructions to install and charge the
être installée près du produit, afin d'assurer une
battery. The
CEC battery charging testing mode
is
accessibilité sécuritaire à la prise de courant.
activated while charging.
10.
Débranchez ce produit de la prise de courant
Even if the parent unit is paired to baby units, the
CEC
avant de procéder au nettoyage. N'utilisez pas de
battery charging testing mode
is activated while it is
powered off and charging.
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.
For cETL compliance only
11.
Débranchez les cordons d'alimentation avant de
remplacer le bloc-piles.
12.
Ne coupez pas les cordons d'alimentation pour
Mesures de sécurité importantes
remplacer les fiches, car ceci peut présenter un
Lorsque vous utilisez votre appareil, vous devriez
danger potentiel.
toujours suivre certaines mesures de précaution
13.
Ne laissez aucun objet reposer ni appuyer sur le
de base afin de réduire les risques d'incendie,
cordon d'alimentation. N'installez pas cet appareil
d'électrocution et de blessures corporelles, dont ceux
dans un endroit où l'on risque d'écraser le cordon
qui suivent:
d'alimentation ou de le piétiner.
1.
Observez toutes les instructions et mises en garde
14.
Ne faites fonctionner cet appareil qu'avec le type
inscrites sur l'appareil.
d'alimentation indiqué sur l'étiquette. Si vous
2.
L'installation par un adulte est requise.
ne connaissez pas le type d'alimentation que
vous possédez à votre domicile, consultez votre
3.
Ce produit a été conçu pour être un dispositif
marchand ou votre compagnie locale d'électricité.
d'appoint seulement. Il n'est pas le remplacement
d'une supervision responsable et adéquate par un
15.
Ne surchargez pas les prises de courant murales
adulte et ne devrait pas être utilisé comme telle.
ni les rallonges électriques.
4.
Ce produit n'est pas conçu pour être utilisé en tant
16.
Ne placez pas cet appareil sur un chariot, meuble,
que moniteur médical.
trépied, support de montage ni table chancelants.
5.
N'utilisez pas cet appareil près de l'eau ni de toute
17.
Les trous et ouvertures du boîtier, situés à l'arrière
autre source d'humidité, par exemple, près d'une
de l'appareil ou sous celui-ci, servent à aérer
baignoire, cuve à lessive, évier de cuisine, dans
l'appareil. Pour l'empêcher de surchauffer, ne
un sous-sol humide ni près d'une piscine, dans un
bloquez sous aucun prétexte ces ouvertures et
soussol humide ou une douche.
Frequently asked questions
Why don't I
hear a sound/
Why can't I hear
Below are the questions most frequently asked about
my baby cry?
the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtechphones.com
or call 1 (800) 595-9511 for customer service.
Why does the
Try the following (in the order
baby monitor
listed) for common cure:
Why does the
not respond
1. Disconnect the power to the
parent unit
normally?
baby unit and the parent units.
beep?
2. Remove the batteries in the
parent units. Then, install the
batteries again.
3. Wait a few minutes before
connecting power back to the
baby units and the parent unit.
4. Turn on the baby unit and the
parent units.
5. Wait for the parent units to
synchronize with the baby unit.
Allow up to one minute for this
to take place.
Why doesn't
Perhaps the rechargeable battery
Why can't I
the screen of
of the parent unit is empty and the
establish a
the parent unit
parent unit is not connected to the
connection?
go on when I
mains. Insert the appliance plug
Why is the
switch on the
into the parent unit and put the
connection lost
unit?
adapter in a wall socket.
every now and
then? Why are
there sound
Why doesn't the
Perhaps the baby unit is not
interruptions?
power on light
connected to the mains. Connect
of the baby unit
the baby unit to the mains.
go on when I
switch on the
Important safety
unit?
Why does the
The units may be too close to
instructions
baby monitor
each other. Make sure the parent
produce a
unit and the baby unit are at least
When using your equipment, basic safety
high-pitched
1 meter/3 feet away from each
noise?
precautions should always be followed to
other.
reduce the risk of fire, electric shock and injury,
Why does the
The baby unit also detects other
including the following:
parent unit react
sounds than those of your baby.
1.
Follow all warnings and instructions marked
too quickly to
Adjust the sensitivity level to a
on the product.
other sounds?
lower level or adjust the speaker
volume on the parent unit.
2.
Adult setup is required.
3.
This product is intended as an aid. It is not
Why does
The lullaby will trigger the vibration
a substitute for responsible and proper adult
the parent
alert frequently. Avoid using lullaby
supervision and should not be used as such.
unit vibrate
and vibration alert at the same
frequently when
time.
4.
This product is not intended for use as a
the lullaby is
medical monitor.
turned on?
5.
Do not use this product near water. For
example, do not use it next to a bath tub, wash
bowl, kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
6.
CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion
n'empêchez pas l'aération adéquate de l'appareil
4.
Assurez-vous que le moniteur et le cordon
en le plaçant sur un lit, divan, tapis ou toute autre
de l'adaptateur sont toujours hors de portée
surface similaire. De même, ne le positionnez pas
des enfants, à au moins 1 mètre (3 pieds) de
à proximité ni au-dessus d'une source de chaleur
l'enfant ou du berceau, pour éviter tout risque de
ou d'un calorifère. De plus, ne placez pas l'appareil
strangulation.
dans un endroit avant de vous assurer qu'il y ait
5.
Ne jamais placer le moniteur à l'intérieur du
une bonne circulation d'air.
berceau ou du parc de bébé. Ne jamais couvrir le
18.
N'enfoncez jamais d'objets à travers les ouvertures
moniteur ou l'unité (s) portative avec un article tel
de cet appareil, car ils pourraient entrer en
une serviette ou une couverture.
contact avec des points de tension dangereux ou
6.
D'autres équipements électroniques peuvent
causer des courts-circuits qui peuvent dégénérer
produire des interférences sur votre moniteur vidéo
en incendies ou en risques d'électrocution. Ne
et audio. Tentez d'installer votre moniteur vidéo
renversez jamais de liquide dans ce produit.
ou audio à l'écart des appareils électroniques
19.
Afin de réduire les risques d'électrocution, ne
tels que des routeurs sans fil, radios, téléphones
démontez pas cet appareil, mais apportez-le dans
cellulaires, interphones, moniteurs, téléphones,
un centre de service autorisé. L'ouverture du
ordinateurs personnels, électroménagers et
mA.
boîtier ou le retrait de toutes pièces que contient
téléphones sans fil.
cet appareil, à l'exception de l'accès autorisé à
Stimulateurs cardiaques implantés dans
certaines portes ou ouvertures, risque de vous
l'organisme
exposer à des points de tension dangereux ou
Les simulateurs cardiaques (ne s'applique qu'aux
d'autres dangers. Un remontage incorrect peut par
la suite présenter des risques d'électrocution.
dispositifs numériques sans fil):
20.
Vous devriez tester la réception chaque fois que
L'organisme 'Wireless Technology Research, LLC
(WTR)', une firme de recherche indépendante,
vous mettez l'appareil en fonction.
a mené une évaluation pluridisciplinaire des
21.
Examinez les composantes afin de vérifier si
interférences entre les téléphones sans fil portatifs
celles-ci ne sont pas endommagées.
et les stimulateurs cardiaques implantés dans
22.
Soyez avisé de la perte de la confidentialité
l'organisme. Appuyée par l'Administration des
lorsque vous utilisez les ondes publiques. Les
aliments et drogues (FDA) des États-Unis, la firme
conversations peuvent être entendues par d'autres
WTR recommande aux médecins:
moniteurs de bébé, des téléphones sans fil, des
Avis aux détenteurs de stimulateurs cardiaques
scanneurs, etc.
•
Vous devriez maintenir les dispositifs sans fil à au
23.
Les enfants devraient être supervisés afin de vous
assurer qu'ils ne jouent pas avec l'appareil.
moins six pouces du simulateur cardiaque.
24.
Le produit n'est pas conçu pour être utilisé par des
•
Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
personnes (incluant des enfants) aux capacités
physiques, sensorielles ou mentales réduites ou
dans une poche de chemise, lorsque celui-ci est
en marche.
qui manquent d'expérience et de connaissances,
à moins qu'on leur ait donné suffisamment
L'étude effectuée par l'organisme WRS n'a pas
de supervision ou d'instructions relativement
identifié de risque pour les détenteurs de simulateurs
à l'utilisation de l'appareil par une personne
cardiaques causés par les gens qui utilisent dispositifs
responsable de leur sécurité.
sans fil à proximité de ceux-ci.
CONSERVEZ CES INSTRUCTIONS
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes
se rapportant aux champs électromagnétiques (EMF)
Mises en garde
standard. Si vous le manipulez correctement en
1.
Utilisez et entreposez le produit à une température
suivant les instructions de ce guide, son utilisation
entre 0˚ C (32˚F) et 40˚C (104˚ F).
sera sécuritaire pendant de nombreuses années,
2.
N'exposez pas cet appareil à des froids ou des
selon les meilleures évidences scientifiques dont nous
disposons aujourd'hui.
chaleurs extrêmes, ainsi qu'à la lumière directe
du soleil. Ne l'installez pas près d'une source de
chauffage.
3.
Le bloc-piles ne doit pas être exposé à la chaleur
excessive telle que la lumière du soleil ou au feu.
if a wrong type of battery is used for the parent
The volume of the parent unit
unit. Use only the supplied rechargeable battery
may have set too low. Press
or replacement battery pack (BT166342/
volume + to increase the volume
BT266342) for the parent unit. Do not dispose
level.
of batteries in a fire. They may explode.
You may have set a low sound
Dispose of used battery according to the
sensitivity level. See Adjust the
information in The RBRC
®
seal.
sound sensitivity of the baby
7. Use only the adapters included with this
unit to change the setting.
product. Incorrect adapter polarity or voltage
If the parent unit is in mute and
can seriously damage the product.
the sound alert feature is on,
Baby unit power adapter:
Input 100-120V AC
there is sound detected from the
150mA 60Hz; Output: 6V DC 600mA;
baby unit.
Parent unit power adapter:
Input 100-120V
The baby units may be out of
AC 150mA 60Hz; Output: 6V DC
400mA.
range. Move the parent unit
8. The power adapters are intended to be
closer to the baby units (but not
correctly oriented in a vertical or floor mount
less than 3 feet).
position. The prongs are not designed to hold
If the parent unit is powered
the plug in place if it is plugged into a ceiling,
by the provided battery, it may
under-the-table or cabinet outlet.
not have enough charge for the
parent unit to perform normally.
9. For pluggable equipment, the socket-outlet
Charge the battery in the parent
shall be installed near the equipment and
unit for up to 11 hours.
shall be easily accessible.
10.Unplug this product from the wall outlet
The baby units may be out of
range. Move the parent unit
before cleaning. Do not use liquid or aerosol
closer to the baby units (but not
cleaners. Use a damp cloth for cleaning.
less than 3 feet).
11.Unplug the power cords before replacing
Other electronic products may
batteries.
cause interference with your baby
12.Do not cut off the power adapters to replace
monitor. Try installing your baby
them with other plugs, as this causes a
monitor as far away from these
hazardous situation.
electronic devices as possible.
13.Do not allow anything to rest on the power
cords. Do not install this product where the
cords may be walked on or crimped.
14.This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply in your home, consult your
dealer or local power company.
15.Do not overload wall outlets or use an
extension cord.
16.Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
17.This product should not be placed in any
area where proper ventilation is not provided.
Slots and openings in the back or bottom
of this product are provided for ventilation.
To protect them from overheating, these
openings must not be blocked by placing the
product on a soft surface such as a bed, sofa
or rug. This product should never be placed
near or over a radiator or heat register.
18.Never push objects of any kind into this
product through the slots because they may
touch dangerous voltage points or create a
short circuit. Never spill liquid of any kind on
the product.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase ("Consumer" or
"you") that the Product and all accessories provided in
the sales package ("Product") are free from defects in
material and workmanship, pursuant to the following
terms and conditions, when installed and used
normally and in accordance with the Product operating
instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the
United States of America and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period ("Materially Defective
Product")?
During the limited warranty period, VTech's authorized
service representative will repair or replace at
VTech's option, without charge, a Materially Defective
Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to
replace the Product, we may replace it with a new or
refurbished Product of the same or similar design.
We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech's
option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working
condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under
the terms of this limited warranty, this limited warranty
also applies to the repaired or replacement Product for
a period of either (a) 90 days from the date the repaired
or replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever
is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1.
Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
2.
Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
3.
Product to the extent that the problem experienced
is caused by signal conditions, network reliability, or
cable or antenna systems; or
4.
Product to the extent that the problem is caused by
use with non-VTech accessories; or
5.
Product whose warranty/quality stickers, product
19.To reduce the risk of electric shock, do
Precautions for users of implanted cardiac
not disassemble this product, but take it to
pacemakers
an authorized service facility. Opening or
Cardiac pacemakers (applies only to digital
removing parts of the product other than
cordless devices):
specified access doors may expose you to
Wireless Technology Research, LLC (WTR),
dangerous voltages or other risks. Incorrect
an independent research entity, led a
reassembling can cause electric shock when
multidisciplinary evaluation of the interference
the product is subsequently used.
between portable wireless devices and
20.You should test the sound reception every
implanted cardiac pacemakers. Supported by
time you turn on the units or move one of the
the U.S. Food and Drug Administration, WTR
components.
recommends to physicians that:
21.Periodically examine all components
Pacemaker patients
for damage.
•
Should keep wireless devices at least six
22.Be aware of possible loss of privacy while
inches from the pacemaker.
using public airwaves. Conversations may
•
Should NOT place wireless devices directly
be picked up by other nursery monitors,
over the pacemaker, such as in a breast
cordless phones, scanners, etc.
pocket, when it is turned ON.
23.Children should be supervised to ensure that
WTR's evaluation did not identify any risk to
they do not play with the product.
bystanders with pacemakers from other persons
24.The product is not intended for use by
using wireless devices.
persons (including children) with reduced
physical, sensory or mental capabilities,
Electromagnetic fields (EMF)
or lack of experience and knowledge,
This VTech product complies with all standards
unless they have been given supervision or
regarding electromagnetic fields (EMF). If handled
instruction concerning use of the appliance
properly and according to the
instructions in this
by a person responsible for their safety.
user's manual, the product is safe to be used based
on scientific evidence available today.
SAVE THESE INSTRUCTIONS
The RBRC
seal
®
Cautions
1.
Use and store the product at a temperature
The RBRC
®
seal on the nickel-metal battery indicates
between 32
o
F and 104
o
F.
that VTech Communications, Inc. is voluntarily
2.
Do not expose the product to extreme cold,
participating in an industry program to collect and
heat or direct sunlight. Do not put the product
recycle these batteries at the end of their useful lives,
close to a heating source.
when taken out of service within the United States and
3.
Batteries should not be exposed to excessive
Canada.
heat such as bright sunshine or fire.
The RBRC
®
program provides a convenient alternative
4.
Make sure the baby unit(s) and the adapter
to placing used nickel-metal batteries into the trash or
cord(s) are always out of reach of the baby,
municipal waste, which may be illegal in your area.
at least 3 feet away from the baby or crib, to
VTech's participation in RBRC
®
makes it easy for you to
avoid a possible strangulation hazard.
drop off the spent battery at local retailers participating
5.
Never place the baby unit(s) inside the
in the RBRC
®
program or at authorized VTech product
baby's crib or
playpen. Never cover the baby
service centers. Please call
unit(s) or parent unit with anything such as a
1 (800) 8 BATTERY
®
for information on Ni-MH battery
towel or a blanket.
recycling and disposal bans/restrictions in your
6.
Other electronic products may cause
area. VTech's involvement in this program is part of
interference with your baby monitor. Try
its commitment to protecting our environment and
installing your baby monitor as far away
conserving natural resources.
from these electronic devices as possible:
RBRC
®
and 1 (800) 8 BATTERY
wireless routers, radios, cellular telephones,
are registered trademarks of
intercoms, room monitors, televisions,
Rechargeable Battery Recycling
personal computers, kitchen appliances and
Corporation.
cordless telephones.
serial number plates or electronic serial numbers
should not rely on any such modification.
have been removed, altered or rendered illegible; or
State/Provincial Law Rights: This warranty gives you
6.
Product purchased, used, serviced, or shipped for
specific legal rights, and you may also have other rights,
repair from outside the United States of America
which vary from state to state or province to province.
or Canada, or used for commercial or institutional
Limitations: Implied warranties, including those of
purposes (including but not limited to Products
fitness for a particular purpose and merchantability (an
used for rental purposes); or
unwritten warranty that the Product is fit for ordinary
7.
Product returned without a valid proof of purchase
use) are limited to one year from the date of purchase.
(see item 2 on the next page); or
Some states/provinces do not allow limitations on
8.
Charges for installation or set up, adjustment of
how long an implied warranty lasts, so the above
customer controls, and installation or repair of
limitation may not apply to you. In no event shall
systems outside the unit.
VTech be liable for any indirect, special, incidental,
How do you get warranty service?
consequential, or similar damages (including, but
not limited to lost profits or revenue, inability to use
To obtain warranty service in the USA, please visit our
the Product or other associated equipment, the cost
website at www.vtechphones.com or call
of substitute equipment, and claims by third parties)
1 (800) 595-9511. In Canada, go to
resulting from the use of this Product. Some states/
www.vtechcanada.com or call 1 (800) 267-7377.
provinces do not allow the exclusion or limitation of
NOTE: Before calling for service, please review the
incidental or consequential damages, so the above
user's manual - a check of the Product's controls and
limitation or exclusion may not apply to you.
features may save you a service call.
Please retain your original sales receipt as proof
Except as provided by applicable law, you assume the
of purchase.
risk of loss or damage during transit and transportation
and are responsible for delivery or handling charges
incurred in the transport of the Product(s) to the
service location. VTech will return repaired or replaced
Product under this limited warranty. Transportation,
delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product
in transit. If the Product failure is not covered by this
limited warranty, or proof of purchase does not meet
the terms of this limited warranty, VTech will notify you
and will request that you authorize the cost of repair
prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the
repair of Products that are not covered by this limited
warranty.
What must you return with the Product to get
warranty service?
1.
Return the entire original package and contents
including the Product to the VTech service location
along with a description of the malfunction or
difficulty; and
2.
Include a "valid proof of purchase" (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3.
Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
Specifications are subject to change without notice.
VTech's responsibilities regarding the Product. There
© 2015 VTech Communications, Inc.
are no other express warranties. No one is authorized
All rights reserved. 06/15. DM222_CIB_V4.0
to make modifications to this limited warranty and you
Document order number: 91-008575-040-100
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment
and receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user's authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with the
FCC criteria. The baby unit shall be installed and used
such that parts of all persons' body are maintained
at a distance of approximately 8 in (20 cm) or more.
The transmitter and antenna of the parent unit shall be
held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
®
This device complies with Industry Canada licence-
exempt RSS standard(s).
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation.
The term ''IC:'' before the certification/registration
Technical specifications
Frequency
Crystal controlled PLL synthesizer
control
Transmit
Baby
unit: 1921.536-1928.448 MHz
frequency
Parent unit: 1921.536-1928.448
MHz
Channels
5
LCD
35 (x) x 21.2 (y) mm B&W LCD
Nominal
Maximum power allowed by FCC
effective
and IC. Actual operating range may
range
vary according to environmental
conditions at the time of use.
Power
Parent unit: 2.4 V Ni-MH battery
requirement
Baby unit power adapter:
Input: 100-120V AC 150mA 60Hz
Output: 6V DC 600mA
Parent unit power adapter:
Input: 100-120V AC 150mA 60Hz
Output: 6V DC 400mA
Advertisement
