Advertisement
Quick Links
Wrist Timer
"the difference is the disk"
Introduction
Congratulations on your purchase of the
TIME TIMER
Time Timer Wrist Timer! No other tool
0
communicates the concept of elapsed
time as well as the Time Timer. Time
Timer reinforces the sense of elapsed
time with a graphic depiction of the time
remaining.
30M
WATER RESIST
Understanding the Timer
The Time Timer Wrist Timer™ provides
a graphical count down timer, using the
patented Time Timer technology. Red
represents the time remaining. The disk
diminishes as time elapses until the
display is blank and no red is visible on
the timer face. Time elapses in a clockwise
direction. When active, the Alarm sounds
to let you know that time has run out.
TIME TIMER
TIME TIMER
TIME TIMER
TIME TIMER
0
0
0
0
30M
30M
30M
30M
WATER RESIST
WATER RESIST
WATER RESIST
WATER RESIST
45 minutes
59 minutes
remaining
remaining
The timer also comes with a convenient
back light, to help you see the display
in low light conditions. Press the LIGHT
button (upper left) to turn on the back
light.
Using the Timer
The timer can be set anywhere from one
minute up to one hour. There is an
audible alarm to let you know when time
has expired.
The timer comes from the factory set
to one hour, and the audible alarm set
to OFF .
To change the settings, see the following
instructions.
REGISTER NOW.
Please return your AX810T registration to the Repair
Center address in the warranty, and we will let you know about future products.
Email ___________________________________________________
User ____________________________________________________
www.timetimer.com
Back light
and Setting
TIME TIMER
0
™
30M
WATER RESIST
TIME TIMER
0
30M
WATER RESIST
• To Start the timer, press the TIMER
button (upper right).
• To Stop the timer, press the TIMER button
TWICE, in rapid succession (press the
button twice within ½ second).
• To Reset the timer, press and hold the
TIMER button for at least 2 seconds.
If turned ON, the Alarm will sound
when time expires. The alarm sounds
for 5 seconds, or until cancelled by
pressing any button.
TIME TIMER
TIME TIMER
TIME TIMER
TIME TIMER
0
0
0
Setting the Timer
AM
AM
The timer must be stopped before changing
settings. The timer uses a standard setting
30M
30M
WATER RESIST
30M
30M
WATER RESIST
WATER RESIST
procedure:
WATER RESIST
Time's up
• Press and hold "S1" to enter setting mode
• Press "S2" to change the field to set
• Press "S3" to change the value of the
field being set
• Press "S4" to exit setting mode
To set the timer, press and hold the
S1 button (upper left) for about three
seconds, until the numbers in the middle
begin to flash, indicating that you have
entered setting mode.
S1 & S4
TIME TIMER
0
30M
S3–
WATER RESIST
Developed by Time Timer LLC, in cooperation with Abilitations,
"improving the lives of children with special needs"
TIME TIMER
0
Start,
Stop, &
Reset
Timer
30M
WATER RESIST
TIMER Button
Press Once to
TIME TIMER
Start and Twice
0
quickly to Stop.
Press and
Hold to Reset.
30M
WATER RESIST
TIME TIMER
0
0
30M
WATER RESIST
S2
TIME TIMER
0
Alarm is On
.
30M
WATER RESIST
S3+
5 YEAR NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year (see back of watch for date). $15 fee applies
thereafter. Return unit with daytime phone number to: AST Repair Center,
3090 Independence Drive, Suite 148, Livermore, CA 94551 USA 800-935-1996
925-290-1900 www.ACCUSPLIT.com • support@ACCUSPLIT.com
Press S2 (upper right) to cycle through
the fields you can set. The fields are: Time
TIME TIMER
setting → Alarm On/Off → Time setting.
0
Press S2 until you see digits in the center
of the display. Now you can set the timer.
Press S3+ (lower right) to increase the
timer set point, and press S3– (lower left)
to decrease the set point. You will see both
the digits and also the dial size increase or
30M
WATER RESIST
decrease. For a setting of 60 minutes, the
dial will show completely red.
Once you have set the desired time, press
S2 once to change Alarm On/Off Setting.
TIME TIMER
You will see the word "ON" or "OFF , " plus
•
0
an alarm
3
symbol, both flashing. Press
S3+ or S3– to turn the Alarm on or off.
AM
Pressing S2 again will return you to the
Timer setting. Press S4 once (upper left)
to exit setting mode. Leaving the timer
unattended for 30 seconds in set mode
30M
causes it to save any changes and then exit
WATER RESIST
set mode.
Setting Notes:
1. You can either press and release S3+
and S3– to change field values, or "press
and hold" either of the S3 buttons to
rapidly change the field value.
2. You can return to the default timer
setting of 60 minutes by simultaneously
pressing S3+ and S3–.
Changing the Battery
TIME TIMER
When the display grows dim or goes out
0
entirely, it is time for a new battery. Using
AM
a small Phillip's head jeweler's screwdriver,
remove the four screws holding back of
timer onto case. Gently slide the old battery
30M
WATER RESIST
from its slot, and replace with new CR2025
Lithium battery. Make sure that the positive
("+") terminal side is facing up.
Power Reset
You can reset the timer to original factory
settings by pressing S3+ and S3– (the two
lower buttons) together, and holding for at
least five seconds.
Manufactured for
Time Timer, Inc.
7707 Camargo Road
Cincinnati, OH 45243
(513) 561-4199
Fax (513) 561-4699
www.timetimer.com
1-877-771-TIME
(1-877-771-8463)
U. S. PATENT NO. D369, 619 & 5,662,479
TIME TIMER
0
AM
30M
WATER RESIST
www.abilitations.com
#998-311A
Advertisement
