Summary of Contents for Life Fitness M051-00K96-0002
Page 1
15” ATTACHABLE TV ASSEMBLY INSTRUCTIONS M051-00K96-0002 REV B...
Page 2
Operating Hours: 08:30-16.30.h (MEZ) 9:00 - 17:00 (BRT) (Monday-Friday) China and Hong Kong Store Operating Hours: Spain LIFE FITNESS Asia Pacifi c LTD 9:00 -20:00 (BRT) (Monday-Friday) LIFE FITNESS IBERIA Room 2610, Miramar Tower 10:00 - 16:00 (BRT) (Saturday) C/Frederic Mompou 5,1º1ª...
Page 4
Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen- tial installation.
Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services as outlined on page one of this manual.
Page 6
Ne jamais faire fonctionner un produit Life Fitness dont la fi che ou le cordon d’alimentation est endommagé, ni aucun appareil qui serait tombé ou aurait été endommagé ou même partiellement plongé dans l’eau. Si cela se produit, communiquer avec le service à...
Page 7
CATV I OTE TO THE NSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guide- lines for proper grounding and, in particular, specifi es that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
: NTSC / ATSC / QAM EDIA ONNECTIONS WITH DIOM 12VDC CATV Hi-Def CVBS Video In Audio In RF Coaxial Audio Out Power In Network In Hi-Def Input S-Video Wired Remote / Media Cable Description Connector Type Power In 12 Volt DC Power In Power Jack Lodgenet Box Connection RJ45...
Page 9
: NTSC / ATSC / QAM EDIA ONNECTIONS Description Connector Type Power In 12 Volt DC Power In Power Jack Video In Video In RCA (yellow) Audio In Stereo Line In RCA (red and white) High-Defi nition Input High-Defi nition Audio & Video Connection High-Defi...
Page 10
: NTSC / ISDB-T EDIA ONNECTIONS Description Connector Type USB Flash Drive USB Type A High Defi nition Input High-Defi nition Audio & Video Connection High-Defi nition D-SUB PC-VIdeo Connection Audio In Stereo Line In RCA (red and white) Video In Video In RCA (yellow) S-Video In...
Page 11
: PAL / SECAM / DVB-T2 EDIA ONNECTIONS Description Connector Type Power In 12 Volt DC Power In Power Jack USB Flash Drive USB Type A High-Defi nition Input High-Defi nition Audio & Video Connection High-Defi nition VGA In PC-Video Connection Video In Video In RCA (yellow)
NSTALLATION Models: 95T Elevation Inspire & 95T Elevation Discover SI Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Main Bracket Cap, (1) Grommet 1. Turn off the treadmill and unplug it from the power outlet. For 95T Elevation Inspire Units Only: Remove the six screws securing the motor cover.
Page 13
5. Remove the two SCREWS (9) securing the REAR CONSOLE COVER (10) to the frame. Remove the rear console cover. Re move the TOP INSERT (11) from the rear console cover and discard. Set the rear console cover aside. 6. Console Cable Connections For 95T Elevation Inspire Units Only: Carefully pull the MEDIA CABLE BUNDLE (12) (Power and Coaxial) from inside the...
Page 14
For Achieve Console Units Only: Remove the two SCREWS (A) and WASHERS (B) securing the BOTTOM INSERT (C). Remove the BOTTOM INSERT. Do not discard the SCREWS and WASHERS. Locate the REMOTE CONTROL (D) and REMOTE BRACKET (E). Feed the REMOTE CABLE (F) 16 E through the large access hole in the REMOTE BRACKET (E).
Page 15
12. Connect all cables to their corresponding jacks located on the bottom of the TV (16). Re move the tape from the end of the MEDIA CABLES (Power, Coaxial, I-R Remote Control, Video). See the Media Connections pages in this manual for detailed information. Feed any excess media cable into the MAIN BRACKET (4).
Models: CLST & 97T (Integrity Series) Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Note: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the Integrity Series Assembly Instructions. Do not install the ACCESSORY TRAYS. 1.
Page 17
6. Attach the ATTACHABLE TV (k) to the MOUNTING BRACKET (j) using four SCREWS (l), WASHERS (m), and SHOULDER NYLON WASHERS (n). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. 7. Connect the AUDIO / VIDEO / I-R REMOTE CONTROL CABLE (a), POWER SUPPLY CORD (b), and the COAXIAL CABLE (c), to the rear of the ATTACHABLE TV (k).
Models: 91TI & 90T Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Note: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the 91Ti, 90T Treadmill Assembly Instructions. Do not install the ACCESSORY TRAYS or PUSH RIVETS. 1.
Page 19
Attach the ATTACHABLE TV (q) to the UPPER MOUNTING PLATE (r) using four SCREWS (s) and NYLON WASHERS (t). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Connect the COAXIAL CABLE (e), REMOTE CABLE (h), & POWER CORD (d) to the rear of the ATTACHABLE TV (q). See the Media Connections pages in this manual for detailed information.
Models: 97TI, 95TI, & 93T Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Note: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the 97Ti, 95Ti Assembly Instructions and 93T Assembly Instructions. Do not install the ACCESSORY TRAYS. 1.
Page 21
9. Connect the COAXIAL CABLE (f), REMOTE CABLE (b) and POWER cord (e) to the rear of the ATTACHABLE TV (n). See the Media Connections pages in this manual for detailed information. 10. Mount the POWER ADAPTER (r) to the bottom of the MOTOR PAN (s) using two CABLE TIES (t). Be sure the cable ties are pulled tight and trim the excess cable ties.
Models: 95X Elevation Inspire & 95X Elevation Discover SI Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Lower Mounting Bracket For 95X Elevation Inspire Units Only: Remove the protective liner from one of the provided fastener strips.
Page 23
FOR 95X ELEVATION INSPIRE UNITS ONLY: 3. Cable Routing Carefully pull the MEDIA CABLE BUNDLE (12) (Power and Coaxial) from inside the CONSOLE BRACKET (15). Unbundle and straighten the media cables. Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together.
Page 24
FOR 95X ELEVATION DISCOVER SI UNITS ONLY: 3. Cable Routing Carefully pull the COAXIAL CABLE from inside the CONSOLE BRACKET (15). Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together. 4.
Page 25
11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR CONSOLE COVER (9) and secure it using the previously removed six SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not overtighten the screws. 12. With the remaining TV BRACKET (20) oriented as shown, install it to the back of the ATTACHABLE TV (21) using four SCREWS (22) and WASHERS (23).
Model: CLSX (Integrity Series) Tools Required: Metric Hex Key Set, Screwdriver, Side Cutters, T-45 Torx Wrench Note: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the CLSX Assembly Instructions. 1. Remove the four SCREWS (a) and COVER PLATE (b) located on the CONSOLE SUPPORT BRACKET TUBE (c). Note: Some models may have a plastic end cap instead of a cover plate.
Page 27
7. Install the DISPLAY CONSOLE (m) as instructed in the Assembly Instructions using the four new SCREWS (n) supplied. Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE (m) to the CONSOLE SUPPORT BRACKET TUBE (c).
Models: 95XI, 93X, & 90X Tools Required: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench Note: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the 95Xi Assembly Instructions or 93X & 90X Assembly Instructions. Do not install the LEFT BULLHORN and BULLHORN COVER. Do not install the ACCESSORY TRAY.
Page 29
11. Connect the COAXIAL CABLE, POWER CORD and I-R REMOTE CONTROL CABLE (d) to the rear of the ATTACHABLE TV (g). See the Media Connections pages in this manual for detailed information. 12. CABLE TIE (m) any excess cable together behind the ATTACHABLE TV (g) and position the cables between the MOUNTING BRACKET (e) and the DISPLAY CONSOLE (4).
Models: 95C/97C Upright Lifecycle® Exercise Bikes Elevation Inspire & 95C/97C Upright Lifecycle® Exercise Bikes Elevation Discover SI Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Lower Mounting Bracket For 95C/97C Elevation Inspire Units Only: Remove the protective liner from one of the provided fastener strips.
Page 31
FOR 95C/97C ELEVATION INSPIRE UNITS ONLY: 3. Cable Routing Carefully pull the MEDIA CABLE BUNDLE (12) (Power & Coaxial) from inside the CONSOLE BRACKET (15). Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together. 4.
Page 32
FOR 95C/97C ELEVATION DISCOVER SI UNITS ONLY: 3. Cable Routing Carefully pull the COAXIAL CABLE from inside the CONSOLE BRACKET (15). Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together. 4.
Page 33
11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR CONSOLE COVER (9) and secure it using the previously removed four SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not overtighten the screws. 12. With the remaining TV BRACKET (20) oriented as shown, install it to the back of the ATTACHABLE TV (21) using four SCREWS (22) and WASHERS (23).
Model: CLSC (Integrity Series) Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Note: The following Assembly Instructions show the console attached prior to TV installation. Follow all appropriate steps when the console is not mounted. 1. Remove the square END CAP (a) and two PLASTIC PLUGS (b) located behind the console on the MAIN CONSOLE SUPPORT TUBE (c).
Page 35
6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV with four SCREWS (r) and four steel WASHERS (s). 7. Assemble the ATTACHABLE TV to the TV MOUNTING BRACKET. Insert one HEX BOLT (t) and WASHER (u) through both parts that make up the hinged bracket.
Models: 95CI, 93C, & 90C Tools Required: Metric Hex Key Set, Side Cutters Note: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as described in the 95Ci, 93C & 90C Assembly Instructions. 1. Locate the SPACER (a). With the SPACER oriented as shown, feed all the console CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the...
Page 37
10. Attach the ADAPTER BRACKET (AA) to the ATTACHABLE TV (k) using four SCREWS (BB). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Attach the ATTACHABLE TV to the UPPER MOUNTING PLATE (m) using four SCREWS (n) and WASHERS (o).
Models: 95R Recumbent Lifecycle® Exercise Bikes Elevation Inspire & 95R Upright Lifecycle® Exercise Bikes Elevation Discover SI Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Lower Mounting Bracket For 95R Elevation Inspire Units Only: Remove the protective liner from one of the provided fastener strips.
Page 39
FOR 95R ELEVATION INSPIRE UNITS ONLY: 3. Cable Routing Carefully pull the MEDIA CABLE BUNDLE (12) (Power and Coaxial) from inside the CONSOLE BRACKET (15). Unbundle and straighten the media cables. Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together.
Page 40
FOR 95R ELEVATION DISCOVER SI UNITS ONLY: 3. Cable Routing Carefully pull the COAXIAL CABLE from inside the CONSOLE BRACKET (15). Install the coaxial extension coupler and coaxial extension cable. Tape the ends of all CABLES (Power, Coaxial, I-R Remote Control, Video) together. 4.
Page 41
11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR CONSOLE COVER (9) and secure it using the previously removed four SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not overtighten the screws. 12. With the remaining TV BRACKET (20) oriented as shown, install it to the back of the ATTACHABLE TV (21) using four SCREWS (22) and WASHERS (23).
Model: CLSR (Integrity Series) Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Note: The following Assembly Instructions show the console attached prior to ATTACHABLE TV installation. Follow all appropriate steps when the console is not mounted. 1.
Page 43
6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV (cc) with four SCREWS (r) and four steel WASHERS (s). 7. Assemble the ATTACHABLE TV to the TV MOUNTING BRACKET. Insert one HEX BOLT (t) and WASHER (u) through both parts that make up the hinged bracket.
Models: 95RI, 93RI, & 90R Tools Required: Metric Hex Key Set, Side Cutters Note: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the 95Ri, 93Ri, 90R Assembly Instructions. 1. Locate the SPACER (a). With the SPACER oriented as shown, feed all the console CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the SPACER.
Page 45
7. Connect the COAXIAL CABLE, POWER cord and remote cable (h) to the rear of the ATTACHABLE TV (k). See the Media Connections pages in this manual for detailed information. 8. CABLE TIE (j) any excess cable together behind the ATTACHABLE TV (k) and position the cables between the MOUNTING BRACKET (c) and the DISPLAY CONSOLE (7).
Model: CLSL (Integrity Series) Tools Required: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench 1. Remove the CONSOLE SUPPORT TOP CAP (a). 2. Remove the two SCREWS (b) securing the CONSOLE SUPPORT COVER (c). Remove the console support cover and set it and the screws aside. 3.
Model: 95LI Tools Required: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench 1. Remove the CONSOLE SUPPORT TOP CAP (A). 2. Remove the two SCREWS (b) securing the CONSOLE SUPPORT COVER (c). Remove the console support cover and set it and the screws aside. 3.
Page 48
9. Connect COAXIAL CABLE, POWER CORD and I-R REMOTE CONTROL CABLE (k) to the rear of the ATTACH ABLE TV (r). See the Media Connections pages in this manual for detailed information. 10. CABLE TIE (w) any excess cable together behind the ATTACHABLE TV (r) and position the cables between the MOUNTING BRACKET (o) and the DISPLAY CONSOLE (e).
Model: CLSS (Integrity Series) Tools Required: Standard Screwdriver, Phillips Screwdriver, Torx Head Screwdriver, Side Cutters, Hex Head Wrench Note: The following Assembly Instructions show the CONSOLE attached prior to ATTACHABLE TV installation. Follow all appropriate steps when the console is not mounted. 1.
Page 50
6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV (bb) with four SCREWS (r) and four steel WASHERS (s). 7. Assemble the ATTACHABLE TV (bb) to the TV MOUNTING BRACKET. Insert one HEX BOLT (t) and WASHER (u) through both parts that make up the hinged bracket.
Model: 95SI, 93S, & 90S Tools Required: Metric Hex Key Set, Side Cutters Note: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as described in the Assembly Instructions. 1. Locate the REMOTE CONTROL (a). Confi gure the remote control for a vertical (c-V) installation.
Page 52
7. Connect the COAXIAL CABLE, POWER CORD and I-R REMOTE CONTROL CABLE (b) to the rear of the ATTACHABLE TV (h). See the Media Connections page in this manual for detailed information. 8. CABLE TIE (c) any excess cable together behind the ATTACHABLE TV (h) and position the cables between the MOUNTING BRACKET (E) and the DISPLAY CONSOLE (9).