Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it has been Ne jamais faire fonctionner un produit Life Fitness dont la fiche ou le cordon d’alimentation est endommagé, ...
Page 6
NOTE TO THE CATV INSTALLER MEDIA CONNECTIONS: NTSC / ATSC / QAM with PRO:IDIOM This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guide- lines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
MEDIA CONNECTIONS: NTSC / ATSC / QAM MEDIA CONNECTIONS: NTSC / ISDB-T Description Connector Type Description Connector Type Power In 12 Volt DC Power In Power Jack USB Flash Drive USB Type A High Definition Input High-Definition Audio & Video Connection High-Definition Video In Video In...
INSTALLATION MEDIA CONNECTIONS: PAL / SECAM / DVB-T2 Models: 95T Elevation Discover SI & Explore Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Main Bracket Cap, (1) Grommet 1. Turn off the treadmill and unplug it from the power outlet. For 95T Elevation Inspire Units Only: Remove the six screws securing the motor cover.
Page 9
5. Remove the two SCREWS (9) securing the REAR CONSOLE COVER (10) to the frame. Remove the REAR CONSOLE For Achieve Console Units Only: COVER. Remove the TOP INSERT (11) from the REAR CONSOLE COVER and discard. Set the REAR CONSOLE Remove the two SCREWS (A) and WASHERS (B) COVER aside.
Models: CLST & 97T (Integrity Series) 12. Connect all cables to their corresponding jacks located on the bottom of the TV (16). Re move the tape from the end of the MEDIA CABLES (Power, Coaxial, I-R Remote Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters Control, Video).
6. Attach the ATTACHABLE TV (k) to the MOUNTING BRACKET (j) using four SCREWS (l), WASHERS (m), Model: OST (Activate Series) and SHOULDER NYLON WASHERS (n). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Tools Required: Phillips Screwdriver, Metric Allen Set, 13 mm Socket 1.
Page 12
5. Attach the INTERMEDIATE BRACKET ASSEMBLY (i) to the BRIDGE TUBE (j) with two M6 X 35MM SCREWS (k) and 9. Attach the BOTTOM CONSOLE TRAY WITH CUTOUT (p) using the previously removed screws, (a) and (b), from two M6 LARGE WASHERS (l). Step 1.
Page 13
11. Attach TV (s) to PRIMARY TV BRACKET (q) using four M6 SCREWS (t) and M6 WASHERS (u). Secure the CAP (v) to Models: INTSC, INTSX, INTDX, Integrity the top of the PRIMARY TV BRACKET (q). Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Lower Mounting Bracket 1.
Page 14
29. Place the TV bracket (2) on the attachable TV (1). 17. Attach the TV bracket (1) to the main bracket (4) using four screws (3) and four washers (2). 30. Place the four washers (3) on the four screws (4). 18.
Models: 95X Elevation Discover SI & Explore FOR 95X ELEVATION INSPIRE UNITS ONLY: 3. Cable Routing Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Carefully pull the MEDIA CABLE BUNDLE (12) (Power and Coaxial) from inside the CONSOLE BRACKET Parts Not Used From Kit: (1) Lower Mounting Bracket (15).
Page 16
12. With the remaining TV BRACKET (20) oriented as shown, install it to FOR 95X ELEVATION DISCOVER SI UNITS ONLY: the back of the ATTACHABLE TV (21) using four SCREWS (22) and WASHERS (23). Tighten the screws securely. (8-10 ft. lbs.) 3.
Model: CLSX (Integrity Series) 7. Install the DISPLAY CONSOLE (m) as instructed in the Assembly Instructions using the four new SCREWS (n) supplied. Tighten the SCREWS to 6-8 in-lbs. Do not Tools Required: Metric Hex Key Set, Screwdriver, Side Cutters, T-45 Torx Wrench overtighten the SCREWS.
Model: OSX (Activate Series) 5. Attach TV (k) to PRIMARY TV BRACKET (d) using four M6 SCREWS (l) and M6 WASHERS (h). Secure CAP (m) to top Tools Required: Phillips Screwdriver, Metric Allen Set of PRIMARY TV BRACKET (d). 1. Remove and discard the four M5 SCREWS (a) attaching the CONSOLE (b) to the CONSOLE SUPPORT BRACKET (c).
Page 19
Models: INXSC, INXSX, INXDX 12. Pull the coaxial cable from inside of the console bracket (3). Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench 13. Install the coaxial extension coupler and coaxial extension Parts Not Used From Kit: (1) Lower Mounting Bracket cable.
Models: 95C/97C Elevation Discover SI & Explore Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench 25. Secure the attachable TV (4) to the main bracket assembly Parts Not Used From Kit: (1) Lower Mounting Bracket using the bolt (1) , washer (2), and nut (3). For 95C/97C Elevation Inspire Units Only: 26.
Page 21
FOR 95C/97C ELEVATION INSPIRE UNITS ONLY: FOR 95C/97C ELEVATION DISCOVER SI UNITS ONLY: 3. Cable Routing 3. Cable Routing Carefully pull the MEDIA CABLE BUNDLE (12) (Power & Coaxial) from inside the CONSOLE BRACKET (15). Carefully pull the COAXIAL CABLE from inside the CONSOLE BRACKET (15). Install the coaxial extension coupler and coaxial extension cable.
11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR Model: CLSC (Integrity Series) CONSOLE COVER (9) and secure it using the previously removed four SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters overtighten the screws.
Model: OSC (Activate Series) 6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV with four SCREWS (r) and four steel Tools Required: Phillips Screwdriver, Metric Allen Set WASHERS (s). 7. Assemble the ATTACHABLE TV to the TV 1.
Page 24
Models: INCSC, INCSX, INCDX R-Series (50L) 5. Attach TV (k) to PRIMARY TV BRACKET (d) using four M6 SCREWS (l) and M6 WASHERS (h). Secure CAP (m) to top of PRIMARY TV BRACKET (d). Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench Parts Not Used From Kit: (1) Lower Mounting Bracket 1.
Page 25
12. Pull the coaxial cable from inside of the console bracket (3). 13. Install the coaxial extension coupler and coaxial extension 25. Secure the attachable TV (4) to the main bracket assembly cable. using the bolt (1) , washer (2), and nut (3). 14.
Models: 95R Elevation Discover SI & Explore FOR 95R ELEVATION INSPIRE UNITS ONLY: Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench 3. Cable Routing Parts Not Used From Kit: (1) Lower Mounting Bracket Carefully pull the MEDIA CABLE BUNDLE (12) (Power and Coaxial) from inside the CONSOLE BRACKET (15).
Page 27
FOR 95R ELEVATION DISCOVER SI UNITS ONLY: 11. Tilt the DISPLAY CONSOLE back into place. Replace the REAR CONSOLE COVER (9) and secure it using the previously removed four SCREWS (8). Tighten the screws securely. (8-10 ft. lbs.). Do not 3.
Model: CLSR (Integrity Series) 6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV (cc) with four SCREWS (r) and four steel WASHERS (s). Tools Required: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters 7. Assemble the ATTACHABLE TV to the TV MOUNTING Note: The following Assembly Instructions show the console attached prior to ATTACHABLE TV installation.
Model: OSR (Activate Series) 5. Attach TV (k) to PRIMARY TV BRACKET (d) using four M6 SCREWS (l) and M6 WASHERS (h). Secure CAP (m) to top of PRIMARY TV BRACKET (d). Tools Required: Phillips Screwdriver, Metric Allen Set 1. Remove and discard the four M5 SCREWS (a) attaching the CONSOLE (b) to the CONSOLE SUPPORT BRACKET (c).
Models: INRSC, INRSX, INRDX R-Series (50L) 12. Pull the coaxial cable from inside of the console bracket (3). Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench 13. Install the coaxial extension coupler and coaxial extension Parts Not Used From Kit: (1) Lower Mounting Bracket cable.
Model: CLSL (Integrity Series) Tools Required: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench 25. Secure the attachable TV (4) to the main bracket assembly using the bolt (1) , washer (2), and nut (3). 1. Remove the CONSOLE SUPPORT TOP CAP (a). 26.
Model: CLSS (Integrity Series) 6. Assemble the MATING BRACKET (q) to the back of the ATTACHABLE TV (bb) with four SCREWS (r) and four steel WASHERS (s). Tools Required: Standard Screwdriver, Phillips Screwdriver, Torx Head Screwdriver, Side Cutters, Hex Head Wrench 7.
Model: 95PS Integrity 7. Install the DISPLAY CONSOLE (m) as instructed in the Assembly Instructions using the four new SCREWS (n) supplied. Tighten the SCREWS to 6-8 in-lbs. Do not Tools Required: Metric Hex Key Set, Screwdriver, Side Cutters, T-45 Torx Wrench overtighten the SCREWS.
Models: 95PS-03 Discover/Explore 12. Pull the coaxial cable from inside of the console bracket (3). Tools Required: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench 13. Install the coaxial extension coupler and coaxial extension Parts Not Used From Kit: (1) Lower Mounting Bracket cable.
Model: 95FS Tools Required: Metric Hex Key Set, Screwdriver, Side Cutters, T-45 Torx Wrench 25. Secure the attachable TV (4) to the main bracket assembly using the bolt (1) , washer (2), and nut (3). Note: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the CLSX Assembly Instructions.
Page 36
7. Install the DISPLAY CONSOLE (m) as instructed in the Assembly Instructions using the four new SCREWS (n) supplied. Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE (m) to the CONSOLE SUPPORT BRACKET TUBE (c).