Epson TM-T88V-DT User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. TM-T88V-DT
  6. User manual
Epson TM-T88V-DT User Manual

Epson TM-T88V-DT User Manual

Hide thumbs Also See for TM-T88V-DT:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
User's Manual
Important Safety Information. . . . . . . . . . . . . . . . . . .page 2
Part Names and Functions. . . . . . . . . . . . . . . . . . . . . .page 5
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 8
Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18
Installing/Replacing the Roll Paper . . . . . . . . . . . page 21
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27
M00081001EN

Advertisement

Table of Contents
loading

Related Manuals for Epson TM-T88V-DT

Summary of Contents for Epson TM-T88V-DT

  • Page 1: Table Of Contents

    User’s Manual Important Safety Information....page 2 Part Names and Functions..... .page 5 Setup.

  • Page 2: Important Safety Information

    WARNING: ❏ If this product produces smoke, a strange odor, or unusual noise, immediately unplug the AC cable, and then contact your dealer or an Epson service center for advice. Continued use may lead to fire or electric shock. ❏...
  • Page 3 Doing so may cause fire. ❏ If water or other liquid spills into this product, immediately unplug the AC cable, and then contact your dealer or an Epson service center for advice. Continued use may lead to fire or shock. ❏...

  • Page 4: Caution Labels

    English Caution Labels The caution label on the product indicates the following precautions. CAUTION: Do not touch the thermal head and the frame on its side because they can be very hot after printing.

  • Page 5: Part Names And Functions

    English Part Names and Functions Roll paper cover Printer LEDs Manual cutter Connector cover Cutter cover Feed button Controller LEDs Cover open button Printer reset button Power button Roll paper cover Open this cover to install/replace the roll paper. Manual cutter Use this cutter when you cut the roll paper manually.

  • Page 6: Connector Cover

    English Connector cover Use the product with this cover attached to protect cables. (U “Attaching/Removing the Connector Cover” on page 11 Controller LEDs Indicates the controller unit status. LED status Meaning ➀ Storage access LED (Green) Accessing storage. ➁ Status LED (Orange) Flashing (with approx.
  • Page 7 English Interface All the ports and connectors are located on the back of the product Drawer kick connector Serial port DC-in connector DisplayPort Line-out port Ethernet port USB ports (× 6) VGA port Note: If the connector cover is attached, detach it to access the ports or connectors. (U “Removing the connector cover”...

  • Page 8: Setup

    English Setup Installing the Product Install the product horizontally on a firm, stable surface. Note: ❏ The security hook on the back of the product allows you to attach a commercially available antitheft wire. Security hook ❏ A tape for fixing the product (DF-10) is available as an option. (U “Securing the Product”...

  • Page 9: Connecting The Ac Adapter

    English Connecting the AC Adapter Follow the steps below to connect the AC adapter. WARNING: Be sure to use the specified AC adapter [AC adapter, T (Model: M284A)]. Connection to an improper power source may lead to equipment damage, fire, or electric shock. CAUTION: Be sure to leave a space between the AC adapter and the main unit.

  • Page 10: Connecting External Devices

    English Connecting External Devices If you connect external devices, turn off the product and then connect each cable to the port/ connector on the back of the product. (U “Interface” on page 7 Note: When connecting the cables whose connectors do not lock themselves (USB cables and line-out cable), pass the cables through the wire saddle to prevent them from coming off.
  • Page 11 English Attaching/Removing the Connector Cover Attaching the connector cover CAUTION: Be sure to hold both sides of the connector cover when attaching it, or it may become damaged. Follow the steps below to attach the connector cover to protect cables. Note: If you use the product with the optional customer display (Model: DM-D110), remove the U-shaped part from the connector cover.

  • Page 12: Removing The Connector Cover

    English 2. Push the connector cover to click onto the main body. 3. Make sure the cables are not pinched. Removing the connector cover Push the connector cover down while pushing the lower part of the both sides of it inward to detach the hooks from the main body.
  • Page 13 English Attaching the Power Button Cover Attaching the power button cover that comes with the product onto the power button prevents accidental operation of the power button. Follow the steps below to attach the power button cover. Note: It is recommended to clean any dirt around the power button before you attach the cover. 1.

  • Page 14: Installing The Customer Display

    Base Screws 1. Attach the base on the TM-T88V-DT with the three screws. (➀ in the illustration) 2. Pass the USB cable of the customer display through the base. (➁ in the illustration) 3. Align the dowel hole in the customer display and the dowel on the base to attach the customer display on the base.
  • Page 15 The pole does not come out of the customer display once it is attached to it. Be sure of its orientation when attaching it to the customer display. 1. Attach the base on the TM-T88V-DT with the three screws. (➀ in the illustration) 2.
  • Page 16 English Changing the orientation of the display Hold the TM-T88V-DT with your hand and move the display or arm to change the direction or angle. CAUTION: Do not rotate the display with excessive force. Doing so may break it. The mobile range of the display is as follows.
  • Page 17 English Securing the Product Using the optional affixing tape (Model: DF-10) secures the product to the installation surface. Follow the steps below to use the affixing tape. 1. Turn over the product so that you can see its bottom. 2. With two pieces of the affixing tape combined, peel off the backing paper of a pair on one side, and paste it to one of the specified positions on the bottom of the product.

  • Page 18: Basic Operations

    English Basic Operations Turning Power On/Off CAUTION: ❏ If you turn the product off, wait more than 10 seconds before you turn it again. ❏ When the product is turned off or when it is in the standby mode, do not hold down the power button longer than 4 seconds.
  • Page 19 English Opening the Covers Opening the roll paper cover Press the cover open button to open the roll paper cover. Opening the cutter cover Slide the cutter cover toward front to open it.
  • Page 20 English Controlling the Speaker Volume You can control the speaker volume through the operating system of the computer. Forced Termination CAUTION: When forced termination is executed, all unsaved data is lost and recovery of the operating system may be required. If you cannot turn the product off using applications or the operating system, you can execute forced termination as a last resort by pressing the power button for approximately 4 seconds.

  • Page 21: Installing/Replacing The Roll Paper

    English Installing/Replacing the Roll Paper Follow the steps below to install/replace the roll paper. 1. Open the roll paper cover. (U “Opening the roll paper cover” on page 19 2. Remove the used roll paper core if there is one. 3.
  • Page 22 English 5. Tear off the paper.

  • Page 23: Cleaning

    Never clean the product with alcohol, benzine, thinner, or other such solvents. Doing so may damage or break the parts made of plastic and rubber. Cleaning the Thermal Head To maintain print quality, Epson recommends cleaning the thermal head periodically (generally every 3 months) by following the steps below. CAUTION: ❏...

  • Page 24: Troubleshooting

    English Troubleshooting (Power) LED does not light Check whether the AC adapter is correctly connected. (U “Connecting the AC Adapter” on page 9 Error LED is on ❏ Check whether the roll paper cover is correctly closed. ❏ If the Paper LED is on, check whether the roll paper is correctly installed and any roll paper remains.
  • Page 25 English The roll paper cover will not open When the autocutter blade is locked, the roll paper cover will not open. Follow the steps below to return the autocutter blade to the normal position. 1. Turn off the product (U “Turning Power On/Off”...

  • Page 26: Specifications

    Approx. 2.8 kg {6.17 lb} *1: The capacity differs depending on the model. *2: 58 mm width paper (57.5 ± 0.5 mm) is also available. For information on how to change paper width, see Technical Reference Guide. *3: Based on Epson operating conditions.

  • Page 27: Appendix

    Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson...

  • Page 28: Open Source Software License

    English Open Source Software License 1 ) This printer product includes open source software programs listed in Section 5) according to the license terms of each open source software program. 2 ) We provide the source code of the GPL Programs and LGPL Programs until five (5) years after the discontinuation of same model of this printer product.
  • Page 29 MICROSOFT SOFTWARE LICENSE TERMS FOR: Windows Embedded POSReady7 These license terms are an agreement between you and SEIKO EPSON CORPORATION. Please read them. They apply to the software included on this device. The software also includes any separate media on which you received the software.
  • Page 30 English Microsoft products and non-Microsoft products you should consult the license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of Remote Assistance or Remote Desktop is permitted without an additional license. f. Font Components. While the software is running, you may use its fonts to display and print content. You may only •...
  • Page 31 Authenticity label with a genuine copy of the software identifies licensed software. To be valid, this label must be affixed to the device, or included on or in SEIKO EPSON CORPORATION’s software packaging. If you receive the label separately, it is not valid. You should keep the label on the device or packaging to prove that you are licensed to use the software.
  • Page 32 English 13. NOT FAULT TOLERANT. The software is not fault tolerant. SEIKO EPSON CORPORATION installed the software on the device and is responsible for how it operates on the device. 14. NO WARRANTIES FOR THE SOFTWARE. The software is provided "as is." You bear all risks of using it.
  • Page 33 You may use the software on the device with which you acquired the software. 2. Additional Licensing Requirements and/or Use Rights a. Specific Use. SEIKO EPSON CORPORATION designed this device for a Point Of Sale Application. You may only use the software for that use.
  • Page 34 3. Scope of License. The software is licensed, not sold. This agreement only gives you some rights to use the software. SEIKO EPSON CORPORATION and Microsoft reserve all other rights. Unless applicable law gives you more rights despite this limitation, you may use the software only as expressly permitted in this agreement. In doing so, you must comply with any technical limitations in the software that allow you to use it only in certain ways.
  • Page 35 Authenticity label with a genuine copy of the software identifies licensed software. To be valid, this label must be affixed to the device, or included on or in SEIKO EPSON CORPORATION’s software packaging. If you receive the label separately, it is not valid. You should keep the label on the device or packaging to prove that you are licensed to use the software.

Table of Contents