Denon AVR-2311CI Owner's Manual page 12

STEP 4
Calculation
11
2Q WKH VFUHHQ XVH ui
STEP 3
WR VHOHFW ³1H[W 1 &DOFXODWLRQ´ DQG
WKHQ SUHVV 
ENTER
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
$872 6(783
$8'<66(< $872 6(783 0XOW(4
67(3 &DOFXODWLRQ >@
1RZ FDOFXODWLQJ
3OHDVH ZDLW

• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
Remote control operation
buttons
STEP 5
Check
12
8VH ui WR VHOHFW WKH LWHP \RX ZDQW
WR FKHFN DQG WKHQ SUHVV 
ENTER
$872 6(783
$8'<66(< $872 6(783 0XOW(4
>@
67(3 &KHFN
&KHFN SURFHVVLQJ UHV
XOWV 7R SURFHHGSUHVV
´1H[Wµ
6SNU &RQILJ &KHFN
'LVWDQFH &KHFN
&K /HYHO &KHFN
&URVVRYHU &KHFN
1H[W 6WRUH
(17(5 (QWHU 5(7851 &DQFHO
6HOHFW LWHP WR FKHFN
• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
• If you want to check another item, press
RETURN
.
13
8VH ui WR VHOHFW ³1H[W 1 6WRUH´
DQG WKHQ SUHVV 
ENTER
NOTE
• If the result differs from the actual connection
status, or if "Caution!" is displayed, see "Error
messages" (vpage 10). Then carry out Audyssey
Auto Setup again.
• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to find the
optimal equalizer settings.
Move the cursor
(Up/Down/Left/Right)
STEP 6
Store
14
6HOHFW ³6WRUH´ DQG WKHQ SUHVV
ENTER
Save the measurement results.
$872 6(783
$8'<66(< $872 6(783 0XOW(4
67(3 6WRUH >@
3UHVV ´6WRUHµ WR VWRUH
FDOFXODWLRQ UHVXOWV
6WRUH
(17(5 (QWHU 5(7851 &DQFHO
$SSO\ DQG VWRUH PHDVXUHPHQW UHVXOW
$872 6(783
$8'<66(< $872 6(783
0XOW(4
67(3 6WRUH >@
1RZ VWRULQJ
3OHDVH ZDLW

• Saving the results requires about 10 seconds.
• If the measuring results are not to be saved,
RETURN
press . A message "Cancel Auto
Setup?" will be displayed. Press o then select
"Yes". All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Confirm the setting
Set up speakers (Audyssey ® Auto Setup)
Finish
15
8QSOXJ WKH VHWXS PLFURSKRQH IURP

WKH XQLW¶V 6(783 0,& MDFN
16
6HW '\QDPLF 9ROXPH Š 
$872 6(783
$8'<66(< $872 6(783
0XOW(4
)LQLVK
6WRULQJ FRPSOHWH
$XWR 6HWXS LV QRZ
ILQLVKHG 3OHDVH XQSOXJ
PLFURSKRQH
7XUQ RQ '\QDPLF 9ROXPH"
<HV 1R
(17(5 ([LW
7XUQ '\QDPLF 9ROXPH RQ DQG H[LW $XWR 6HWXS
• For details of Dynamic Volume settings, see
page 55.
n When turning Dynamic Volume on
• Use o to select "Yes", and then press
The unit automatically enters "Evening" mode.
n When turning Dynamic Volume off
• Use p to select "No", and then press
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
Return to previous menu
ENGLISH
>@
ENTER
.
ENTER .
9