1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Nail Gun
  5. NT 65M2 (S)
  6. Handling instructions manual

Hitachi NT 65M2 Handling Instructions Manual

Hide thumbs Also See for NT 65M2:
Table of Contents

Advertisement

Quick Links

See also: Technical Data and Service Manual , Handling Instructions Manual
Finish Nailer
Model NT 65M2

Handling instructions

Note:
Before using this Pneumatic Power Tool, carefully read through
these HANDLING INSTRUCTIONS to ensure efficient, safe operation.
It is recommended that these INSTRUCTIONS be kept readily
available as an important reference when using this power tool.

Advertisement

Table of Contents
loading

Related Manuals for Hitachi NT 65M2

Summary of Contents for Hitachi NT 65M2

  • Page 1: Handling Instructions

    Finish Nailer Model NT 65M2 Handling instructions Note: Before using this Pneumatic Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool.

  • Page 2: General Operational Precautions

    GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING NAILER 1. Operate the power tool safely for correct uses. Safe operation through correct usage This tool was designed for driving nails into wood Do not use the power tool for uses other than and similar materials.
  • Page 3 – fitting transportation safety systems e.g. on such a case do not use the power tool until it vehicles and wagons has been inspected and repaired. 19. Do not disconnect the hose with your finger on If merely pulling the trigger causes operating the trigger.

  • Page 4: Name Of Parts

    NAME OF PARTS Top cover Exhaust vent Blow nozzle knob Air outlet of blow nozzle Exhaust cover Valve part Piston o-ring Air plug Body Piston Driver blade Magazine cover Trigger Nail feeder Lock lever Guide plate (A) Nose cap Magazine Push lever Nail rail Adjuster...

  • Page 5: Before Use

    Concave portion in the vicinity during operation. Magazine cover 1. Nailing procedures Nail feeder This Hitachi nailer is equipped with a nailer operation switching device. Use SINGLE ACTUATION MECHANISM or CONTACT ACTUATION MECHANISM in accordance with the work to be performed.
  • Page 6 (1) Intermittent nailing Previously pull the trigger Set the switching device to the upward position (to set to SINGLE ACTUATION MECHANISM) (See Fig. Depress the nail outlet onto the desired point; then pull the trigger to drive a nail in a single shot (See Fig.

  • Page 7: Inspection And Maintenance

    5 Close guide plate (A) and latch. starting work. 6 In case of frequent jam, contact a Hitachi Oil in the body or drained water from the compressor authorized service center. can sometimes spout out of the air outlet of blow nozzle.
  • Page 8 D: Remarks CAUTION Repair, modification and inspection of Hitachi Power NOTE Tools must be carried out by a Hitachi Authorized Due to HITACHI’s continuing program of research and Service Center. development, the specifications herein are subject to This Parts List will be helpful if presented with the change without prior notice.
  • Page 11 982454 949657 M6×12 885658 880515 877763 I.D 14 885673 884963 885637 M5×25 873570 P-18 885671 676531 885672 884964 882914 872654 1AP-10 882913 884966 883992 I.D 20.8 878888 I.D 1.8 882927 884965 885668 I.D 31.7 884962 885667 876465 885663 885646 885690 S-44 885648 885665...
  • Page 12 Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, 108-6020 Japan Code No. C99146711 Printed in Taiwan...

Table of Contents