Whirlpool WTW8540BC1 Use And Care Manual page 12

WASHER CARE (cont.)
f. Press the START/PAUSE button to begin the cycle.
The Clean Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER. (For models with no
Power button, press and hold START/PAUSE for three
seconds). After the Clean Washer cycle has stopped, run
a Rinse/Drain & Spin cycle to rinse cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will fill to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may find some
residue buildup in the washer's dispensers. To remove
residue from the dispensers, wipe them with a damp cloth
and towel dry. Do not attempt to remove the dispensers or
trim for cleaning. The dispensers and trim are not removable.
If your model has a dispenser drawer, however, remove the
drawer and clean it before or after you run the Clean Washer
cycle. Use an all-purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
NON=USE AND VACATION CARE
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding
due to water pressure surge.
WINTER STORAGE CARE
iMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and
run washer on RINSE/DRAIN & SPIN cycle for about
30 seconds to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
r
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2.
3.
4.
5.
6.
7.
If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
Disconnect drain from drain system.
Unplug power cord.
Place inlet hoses inside washer basket.
Drape power cord and drain hose over the console
and secure with masking tape.
Place foam packing ring from original shipping materials
back inside washer. If you do not have packing ring,
place heaw blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in
new location.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
r
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2=
To
1.
2.
3.
Before using again, run washer through the following
recommended procedure:
use washer again:
Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
Plug in washer or reconnect power.
Run washer through BULKY ITEMS cycle to clean
washer and remove antifreeze, if used. Use only HE
High Efficiency detergent. Use half the manufacturer's
recommended amount for a medium-size load.
12