Kenmore 795.51379012 Use & Care Manual page 13

4. FASTEN THE SHUTOFF VALVE
Fasten the shutoff
valve
to the cold water pipe with the pipe
clamp.
Pipe Clamp--_k
Saddle-Type j _ |__ Vertical Cold
Shutoff Valve Water Pipe
NOTE: Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and
use is not permitted in Massachusetts. Consult with your
licensed plumber.
&TIGHTEN THE PiPE CLAMP
Tighten the clamp screws until the sealing washer begins to
swell. Washer
Pipe Clamp -- Inlet End
Clamp Screw-
NOTE: Do not overtighten or you may crush the tubing.
&ROUTE THE TUBING
Route the tubing between the cold water line and the
refrigerator. Route the tubing through a hole drilled in the wail
or floor (behind the refrigerator or adjacent base cabinet] as
close to the wail as possible.
NOTE: Be sure there is sufficient extra tubing [about 8 feet
(2.4 m) coiled into 3 turns of about 10" (254 mm) diameter]
to allow the refrigerator to move out from the wail after
installation.
7. CONNECT THE TUBING TO THE VALVE
Place the compression nut and ferrule (sleeve) for copper
tubing onto the end of the tubing and connect it to the shutoff
valve. Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
Saddle-Type
Shutoff Valve
Pacldng"__
Nut
Outlet
Valve
Compression
Nut
_rule (sleeve)
NOTE: Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and
use is not permitted in Massachusetts. Consult with your
licensed plumber.
&FLUSH OUT THE TUBING
Turn the main water supply on and flush out
the tubing until the water is dear.
Shut the water off at the water valve after
about one quart of water has been flushed
through the tubing.
9.CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
* Before making the connection to the refrigerator, be sure the
refrigerator power cord is not plugged into the wall outlet.
° If your refrigerator does not have a water filter, we
recommend installing one. If your water supply has sand
or particles that could clog the screen of the refrigerator's
water valve, install the filter in the water line near the
refrigerator.
° Do not use old hoses; only use new hoses provided by
the manufacturer. For more information caii 1-800-4-MY-
HOME®.
1. Remove the plastic flexible cap from the refrigerator
connection.
2. Place the compression nut and ferrule (sleeve) onto the end
of the tubing. (See figure 1)
3. Insert the end of the tubing into the connection as far as
possible. While holding the tubing, tighten the fitting.
CAUTION: Review that leaks are not occurring in the
water line.
Back of refrigerator
Tubing
1/4" (6.35 ram'
Compression
Nut _
Ferrule
(Sleeve)
Figure 1
1/4"(6.35 mm) Tubing
)
Refrigerator
Connection
Fasten the tubing into the tubing clamp attached to the back
of the refrigerator. First, loosen the screw fastening the clamp.
Next, insert the tubing in the groove. Finally, re-fasten the
screw.
10. PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it
does not vibrate against the back of the
refrigerator or against the wall. Push the
refrigerator back to the wall.
11.START THE ICEMAKER
Set the icemaker power switch to the ON position. The
icemaker wil! not begin to operate until it reaches its
operating temperature of 15°F (-9°C) or below. It will then
begin operation automatically if the icemaker power switch is
in the I (on) position.
14