Advertisement
Quick Links
Cordless Impact Driver
Dimensions
(C x W x
HI
Capacities
No load
Impacts
Max
speed
per
tightening torque
Machine screw and bolt
IRPM)
minute
(Note
1)
MODEL 6 9 0 1 D
MODEL 6901DW
With Fast Charger
Net
weight
INSTRUCTION MANUAL
Battery Cartridge
9100
SPEC IF I CAT1 0 N S
Model D C 9 7 0 0 Fast Charger
Voltage
1
Charging time
1
Input
I
output
9.6
V
1
1
Hr.
1
A.C. only 5 0 H z
-
60Hz
1
D.C.
7 . 2 V . 9 . 6 V
~~
Note 1 After tightening high tensile bolt MlOFllT for
3
seconds while using a fully charged battery cartridge
*
Manufacturer reserves the right to change specifications without notice
Note Specifications may differ from country to country
Advertisement
Related Manuals for Makita 6901D
Summary of Contents for Makita 6901D
- Page 1 Cordless Impact Driver INSTRUCTION MANUAL SPEC IF I CAT1 0 N S Capacities No load speed Machine screw and bolt IRPM) 9100 Battery Cartridge Voltage Charging time Note 1 After tightening high tensile bolt MlOFllT for Manufacturer reserves the right to change specifications without notice...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed f r o m tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger o n switch. Be sure switch is OFF when plugging 16.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord 12. To reduce risk of electric shock, unplug charger from outlet before attemp- ting any maintenance or cleaning. Turning off controls will not reduce this risk. This manual...
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. - Page 6 Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. * T o remove the battery cartridge, pull out plate and grasp both sides of the cartridge while withdrawing it from the tool.
- Page 7 Installing or removing driver bit CAUTION : Always be sure that the tool installing or removing the bit. Slide the toward the motor and in- sleeve sert the bit into the sleeve go. Then release the sleeve bit. To remove the bit, slide the sleeve toward the motor and pull the bit out firmly.
- Page 8 Operation The proper tightening torque may differ depending upon the kind or size of the screw, the material of the workpiece to be tightened, etc. The relation between tightening torque and tightening time is shown in the figures below. Machine screw lbsl ( 4 ) Standard bolt...
- Page 9 Hold the tool firmly and place the point of the driver bit in the screw head. Apply for- ward pressure t o the tool t o tool on to start operation. NOTE : Use the proper bit for the head of the screw that you wish to use. Hold the tool pointed straight If you tighten the screw for a time longer than shown in the figures above, the screw or the point of the driver bit may be overstressed, stripped, damaged, etc.
-
Page 10: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 11 ACCESSORIES CAUTION These accessories or attachments are recommended for use w i t h your Makita tool specified i n this manual. The use o f any other accessories accessories or attachments should be used only i n the proper and intended manner.
-
Page 12: Cordless Impact Driver
Jan.-l8-'89 CORDLESS IMPACT DRIVER Model 6901D Note: The switch and other part configurations may differ from country to country. - Page 13 MODEL 6901D Name Plate Housing Set IWith Item 211 Switch Lever Switch Switch Plate DC Motor 9 Spindle Ball 5 6 Steel COmDreSSlOn S P r V 2 4 HBmmer Anvil Steel Ball 3 5 Flat Washer 14 '7;'," $ . &...
- Page 14 8’ MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.