Table of Contents
Advertisement
Do not remove the anode leaving the tank unprotected.
By
doing so, all warranty on the water heater tank is voided.
"AIR" IN HOT WATER FAUCETS
Explosion
Hazard
• Flammable
hydrogen
gases may be present.
• Keep all ignition
sources
away
from
faucet
when
turning
on hot water.
2. Remove the screw securing the access panel, then remove
the panel.
3. Fold the insulation back to expose the thermostat.
4. Reset the high limit by pushing in the red button marked
"RESET".
-- RESET
BUTTON
HYDROGEN
GAS: Hydrogen gas can be produced
in a hot
water system that has not been used for a long period of time
(generally
two weeks or more). Hydrogen
gas is extremely
flammable
and explosive.
To prevent the possibility of injury
under these conditions, we recommend
the hot water faucet
be opened for several minutes at the kitchen sink before any
electrical
appliances
which are connected
to the hot water
system are used (such as a dishwasher
or washing machine).
If hydrogen gas is present, there wilt probably be an unusual
sound similar to air escaping through the pipe as the hot water
faucet is opened. There must be no smoking or open flame near
the faucet at the time it is open.
RUMBLING NOISE
In some water areas, scale or mineral deposits wilt build up on
your heating elements. This buildup wilt cause a rumbling noise.
Follow Element Cleaning/Replacement
instructions to clean and
replace the elements.
HIGH TEMPERATURE
SHUT OFF SYSTEM
The water heater has a high limit shut off system with a reset
button located on the thermostat.
Follow the resetting instructions which refer to the high limit
behind the access panel.
• Before
removing
any access
panels or servicing
the water
heater, make sure the electrical
supply to the water heater is
turned "OFF".
• Failure to do this could result in
death, serious bodily injury, or
property damage.
1. Before beginning, turn "OFF" electrical power supply to the
water heater.
FIGURE 33.
FIGURE 34.
5. Replace
the insulation
so that it completely
covers
the
thermostat and element.
6. Replace the access panel.
7. Turn "ON" electric power to the water heater.
If the high limit must be reset again, call Sears Service Department
to find out why the high limit turned "OFF" the electric power
NOT ENOUGH OR NO HOT WATER
1.
In a new installation, the water heater may not be properly
connected. Make sure the cold water supply valve is open.
Review and check piping installation.
Make sure that the
cold water line is connected to the cold water inlet to the
water heater and the hot water line to the hot water outlet
on the water heater.
2.
Make sure the electrical supply to your water heater is "ON".
3.
Check for loose or blown fuses in your water heater circuit.
Circuit breakers weaken with age and may not handle their
rated load and should be replaced.
4.
Make certain the disconnect switch, if used, is in the "ON"
position.
5.
Check to see the electric service to your house has not been
interrupted. If this is the case, contact the electric company.
6.
Is the thermostat
set to the desired temperature?
See
Temperature Regulation section.
7.
Ifyou had experienced very hot water and now no hot water,
the problem may be due to the high temperature
shut off
system. See High Temperature
Shut Off System in the
Troubleshooting section.
8.
During very cold weather, the incoming water will also be
colder and it wilt require a longer time to become heated.
9.
The hot water usage may exceed the capacity of the water
heater. If so, wait for water heater to recover after abnormal
demand. Also examine pipes and faucets for possible water
leaks.
10.
If you can not determine the problem, then call the Sears
Service Department.
WATER IS TOO HOT
Adjust the thermostat to a lower setting. See the Temperature
Regulation section.
23
Hide quick links:
Advertisement
Table of Contents
