Table of Contents
Advertisement
Quick Links
*314702*
314702
Printed: 08.07.2013 | Doc-Nr: PUB / 5071307 / 000 / 01
WFO 280
Bedienungsanleitung
Operating instructions
Mode d'emploi
Istruzioni d'uso
Gebruiksaanwijzing
Manual de instruções
Manual de instrucciones
Brugsanvisning
Käyttöohje
Bruksanvisning
Οδηγιες χρησεως
Instrukcja obsługi
Návod k obsluze
Schwingschleifer
Orbital finishing sander
Ponceuse vibrante
Levigatrice orbitale
Vlakschuurmachine
Lixadeira vibratória
Lijadora orbital
Rystepudser
Tasohiomakone
Planslipmaskin
Λειαντήρας έκκεντρης παλινδρ μησης
Szlifierka Oscylacyjna
Vibrační bruska
1– 6
7–12
13–18
19–24
25–30
31–36
37–42
43–48
49–54
55–60
61–66
67–72
73–78
79–84
Advertisement
Table of Contents
Related Manuals for Hilti WFO 280
Summary of Contents for Hilti WFO 280
- Page 1 *314702* WFO 280 314702 Bedienungsanleitung Schwingschleifer 1– 6 Operating instructions Orbital finishing sander 7–12 Mode d’emploi Ponceuse vibrante 13–18 Istruzioni d’uso Levigatrice orbitale 19–24 Gebruiksaanwijzing Vlakschuurmachine 25–30 Manual de instruções Lixadeira vibratória 31–36 Manual de instrucciones Lijadora orbital 37–42 Brugsanvisning Rystepudser 43–48...
- Page 2 Printed: 08.07.2013 | Doc-Nr: PUB / 5071307 / 000 / 01...
-
Page 3: Safety Rules
WFO 280 orbital finishing sander Symbols 1. Safety rules tool will increase the risk of electric e) Do not overreach. Keep proper foot- shock. ing and balance at all times. This d) Do not abuse the cord. Never use the enables better control of the power tool 1.1 General safety rules... - Page 4 Disconnect the protection mended by Hilti for wood dust and/or supply cord plug from the socket . Dam- 1.1.5 Service mineral dust together with this tool.
-
Page 5: Technical Data
■ Trouble-free operation of the machine can ■ The following instructions must be Power input: 350 W be ensured only when Hilti original acces- observed. Incorrect operation may pre- Power output: 200 W sories are used. sent a risk of damage or injury. -
Page 6: Correct Use
If the clamping bar is loose, it may cause dam- Operation age to the casing of the machine ■ Hold the machine securely and main- ■ Use only original Hilti sanding sheets with tain a secure stance. Velcro-type attachment pads. The mains supply voltage must correspond to the information printed on the rating plate. -
Page 7: Dust Extraction
The information contained in these operating 1. The built-in dust extraction system with with the workpiece. Position the machine on a Hilti Service Centre after a long period of instructions is protected by copyright and the surface to be sanded so that the entire dust bag (fig.5) -
Page 8: Manufacturer's Warranty - Tools
12. EG declaration of conformity (original) – tools Most of the materials from which Description: Orbital finishing sander Hilti warrants that the tool supplied is Hilti power tools are manufac- Serial no.: 000000000–999999999 free of defects in material and work- tured can be recycled. - Page 9 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2232 0213 10-Pos. 1 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O. Printed: 08.07.2013 | Doc-Nr: PUB / 5071307 / 000 / 01...