Magnavox ZV450MW8A Owner's Manual page 43

Analog TV
For channel number 2-6 press, press [B] or [ • ] to decide the channels. For other channels (7-69),
the channel will be decided as soon as you enter the channel number.
Analog CATV For channel number 1-12 press, press [B] or [ • ] to decide the channels. For other channels (13-
125), the channel will be decided as soon as you enter the channel number.
Digital TV For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
Digital CATV
For channel number 1-13 press, press [B] or [ • ] to decide the channels. For other channels (14-
135), the channel will be decided as soon as you enter the channel number.
minor channels For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
<Hint>
• You can decide the 1-digit channel number by pressing 0 first , then enter desired 1-digit channel number.
e.g.) "5": [0]+[5]
• For selecting the channels with [K / L] you need to press [B] or [ • ] to decide the channel number.
• For selecting the minor channels with [K / L], please make sure the minor channel your are selecting is existed.
[K / L] does not skip the non-existed minor channels.
To stop the timer recording in progress
Press [STOP C] / [STOP/EJECT C A] on the front panel
of the unit to stop the timer recording in progress.
[STOP C] on the remote control is not effective.
Checking, canceling, or correcting the timer
programming information
1) Press [TIMER SET].
2) Press [TIMER].
3) Check the information.
Timer Programming
JAN/ 2/07 12:00 AM 125.1 SP
SP (1:00)
Date Start
JAN/02 12:00AM 1:00AM
New Program
4-A) To delete the timer program:
1 Use [K / L] to select the program you want to
delete, then press [OK].
2 Use [K / L] to select "Delete", then press [OK].
Confirmation window will appear.
3 Use [K / L] to select "Yes", then press [OK].
4-B) To correct the timer program:
1 Use [K / L] to select the program you want to
correct, then press [OK].
2 Use [K / L] to select "Program Change", then
press [OK].
3 Correct the timer program by using
[K / L / { / B], then press [OK].
5) Press [TIMER] to exit.
6) Press [TIMER SET] to return to the timer standby
mode.
Note
• Press [TIMER] to check the timer recording in progress.
When the timer recording is proceeding, that
program will be highlighted with red. In this case,
you cannot select any other program.
TIMER RECORDING
How to select a channel number for the timer recording
MON JAN/01 11:00AM
End CH
DTV125. 1
If the timer program did not complete correctly,
the error number appears in the timer pro-
gramming list.
Timer Programming
Date Start
E41 JAN/02 12:00AM 1:00AM
New Program
Each error number means:
E1-22 Recording error other
E37-39 than below
E24 Unrecordable disc
E25-26 Copy prohibited
program
E29 Disc protected
E30 Disc full
E35 PCA full *1
E36 Already finalized
video format disc
E40 Some portion has
not been recorded
because of program
overlapping.
Recording did not
start at the start time.
• E23, E27, E28, E31, E32, E33 and E34 are not displayed.
• A program with the error number is grayed in the timer
programming list.
• Once the timer programming list with error line(s) is
displayed, or after canceling and setting again the timer
standby mode, the program line(s) with error will be
cleared.
*1 PCA is a disc's space reserved for recording test.
TUE JAN/02 11:00AM
End CH
DTV125. 1
1/1
E41 Power failed
E42 No disc when
recording
E43 Already 49 titles
recorded
E44 Already 254 chapters
recorded
E45 Copy prohibited
program
E46 It is impossible to
record additionally
on a disc recorded
by other units
when setting "
Make Recording
Compatible" to "OFF".
EN EN 43 43