Table of Contents
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Preparation
Downrod
7
Blades
Switch Housing
13
1
M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company
Mounting Options
Ladder
3
Wiring
8
Maintenance
& Cleaning
14
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Canopy
11
12
Troubleshooting
?
?
?
16
17
Advertisement
Table of Contents
Related Manuals for Hunter Sea Air 53061
Summary of Contents for Hunter Sea Air 53061
- Page 1 To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Maintenance Blades Switch Housing & Cleaning Troubleshooting M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
-
Page 2: What To Expect With Your Installation
ANSI/NFPA 70. If you are unfamiliar Check box to see with wiring, use a qualified electrician. fan weight Assess ceiling angle Select a downrod length c.2 - Use only Hunter replacement parts. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... -
Page 3: Tools Needed
Tools Needed www.HunterFan.com 1.888.830.1326 Pliers Wire Strippers 11/32” Wrench Ladder Power Drill 9/64” Drill Bit Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... -
Page 4: Mounting Options
You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... -
Page 5: Ceiling Bracket
Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... - Page 6 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 7 Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 8 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 9 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 10 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 11 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 12 Install the two canopy lifted into place, the canopy fits into the screw holes are aligned. screws, found in the hanging bracket as shown. hardware bag. Note: Fan style may vary. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
- Page 13 Lightly attach the blade irons to the Secure each blade to a blade iron with motor with screws found in screws found in the hardware bag. hardware bag, then securely tighten after both screws are attached. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
-
Page 14: Switch Housing
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... - Page 15 Install plug connectors. the three switch housing screws found in the hardware bag. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company...
-
Page 16: Maintenance And Cleaning
Cleaning the fan - use soft from high to off. flow - move the reverse switch brushes or cloths to prevent to the opposite position. scratching. Cleaning products may damage the finishes. M3554-01 • 08/24/15 • © 2013–2015 Hunter Fan Company... -
Page 17: Troubleshooting
• Make sure power switch is on. • Tighten all of the blade and blade iron screws until they • Pull the pull chain to make sure Hunter fans have the power to cut your cooling costs up are snug. to 40%. it is on.