Effects To Monitor; Preset Select - Mackie CFX SERIES Owner's Manual & Warranty

EMAC effects, with their levels already deter-
mined by the channels' EFX 2 (EXT) knob, you'll
typically set this knob near the "U" mark and
then leave it alone.

EFFECTS TO MONITOR

This works just like the channel AUX
knobs, but here, the source signal is the EFX 2
RETURN and the EMAC output. Typically, this
knob is used to add effects to the stage monitors.
Turned fully up, it provides 15 dB of addi-
tional gain, the center "U" mark is unity gain,
and fully down is off.

PRESET SELECT

Rotate this detented switch to select the
preset effect you want to use.
Preset Effects Descriptions
Reverbs
The reverbs are designed to provide a wide
variety of reverb sounds for vocal and instru-
ment applications. In the following description,
tail refers to the reflections that follow the initial
sound event, also referred to as decay range.
Pre-delay is the amount of time between the
initial sound event and the first reflection.
TIME/RATE
controls the length of the
tail, with the shortest tail at the 0 position and
the longest tail at 10. DAMPING/DEPTH
controls the damping, with the darkest tone at
0 and the brightest tone at 10. The WIDE
switch is very effective at increasing the stereo
image of the reverb effect.
REVERSE: Standard reverse reverb, simulat-
ing a tail-first effect
increasing to the original
note. Decay range is ad-
justable from 35ms to
515ms. No pre-delay.
GATED: Standard
gated reverb, where the
reverb tail is cut off
sharply after the preset
decay length. Decay
range is adjustable from
35ms to 515ms. No pre-
delay.
CATHEDRAL: Dense,
smooth reverb with very
long tail, long pre-delay,
and late reflections. Tails
are very warm with some
additional high-end
reflections imitating the
stone walls of a cathedral.
18
A very dramatic effect that works well with wind
instruments such as flute, slow finger picking on
acoustic guitar, and quiet vocal group harmony
and choirs. Also works well with keyboards and
drums using short decay. Decay range is adjust-
able from 2 seconds to 10 seconds. Pre-delay set
at 75ms.
LG. HALL: Dense, smooth reverb with long
tail, long pre-delay, and some early reflections.
Tails are warm with more apparent high end.
Works well with vocals and electric and acoustic
guitar. Decay range is adjustable from 1 second
to 5 seconds. Pre-delay set at 75ms.
MD. HALL: Dense, smooth reverb with nor-
mal tail, normal pre-delay, and increased early
reflections. Tails are warm with more apparent
high end. Works well with vocals and electric
and acoustic guitar. Decay range is adjustable
from 750ms to 2.5 seconds. Pre-delay set at 65ms.
LG. PLATE: Good early reflections and no
pre-delay. Tails are normal and warm with
strong high end for increased presence. Perfect
for vocals and snare. Decay range is adjustable
from 1 second to 5 seconds. No pre-delay.
MD. PLATE: Good early reflections and no
pre-delay. Tails are short and warm with strong
high end for increased presence. Perfect for
tight vocals and snare. Decay range is adjust-
able from 750ms to 2.5 seconds. No pre-delay.
SM. ROOM: Reverb featuring very fast and
scattered early reflections with a short pre-delay.
Tails are very short and warm with normal high-
end imitating absorbent wall materials and
audience. Good for tight vocal effects. Decay
range is adjustable from 250ms to 1 second.
Pre-delay set at 30ms.
SPRING: Mimics the
vintage 60's-style wet
spring reverb effect. Tails
are normal with strong
high end and a slight wa-
ver imitating the slow
flutter of the mechanical
spring system. Very good
with acoustic guitar.
Decay range is adjust-
able from 1 second to 5
seconds. No pre-delay.
Delays
There are four delays
available with one, two,
three, and four repeats.
TIME/RATE
the time between repeats,
with the fastest repeats
at the 0 position and the
controls