Pentair GLOBRITE Installation And User Manual

Color changing underwater led light for pool and spa

Hide thumbs Also See for GLOBRITE:

Installation and user manual (20 pages)

Installation and user manual (72 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Pentair GLOBRITE

Page 1 GLOBRITE COLOR CHANGING ™ UNDERWATER LED LIGHT FOR POOL AND SPA INSTALLATION USER’S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS GLOBRITE™ Color Changing LED Pool/Spa Light Installation and User’s Guide...
Page 2: Table Of Contents
Installing the GloBrite Color Light Sleeve and Niche (after electrical requirements are met) ..............4 Installing the GloBrite Color Light Sleeve and Niche in a Concrete/Gunite Pool . 4 Option 1: Light Niche Sleeve with Cone ............5 Option 2: Conduit to Light Niche ..............6 Installing GloBrite Color Light in a Fiberglass Pool ..........
Page 3: Important Warning And Safety Instructions
Improper installation will create an electrical hazard, which could result in death or serious injury to pool user, installer or other due to electrical shock and may also cause damage to the property. GLOBRITE™ Color Changing LED Pool/Spa Light Installation and User’s Guide...
Page 4 ELECTRIC CODE (NEC). UNBONDED LIGHTING NEC PROVISIONS: When the UL listed non-metallic GloBrite Color LED Light low voltage lights are used with the GloBrite light approved niches (as listed on page 19), the current NEC provides an exception to luminaire bonding and grounding in Article 680.6 and 680.23 POOL WATER BONDING NEC PROVISIONS :For Pool Water Bonding required by NEC Article 680.26C, concrete pools are considered conductive (refer to 680.26...
Page 5: Globrite Color Changing Led Pool Light Overview
The GloBrite color light can be manually controlled using a standard wall-mount light switch. Multiple GloBrite color lights can be connected via a junction box and a 12 VAC isolation transformer to a single switch so that all lights can be switched on and off together.
Page 6: Operating Globrite Color Lights Using A Wall Switch
12 VAC transformer to a single switch so that all lights can be switched on and off together. GloBrite color lights are controlled by cycling AC power to the 12 VAC transformer from a standard wall switch. By turning the switch on and off a specific number of times, the light activates one of the seven light show modes, fixed colors, or enables the “Hold”...
Page 7: Saving A Color Mode Or Fixed Color
For example, while in “Party Mode” switch the light off. Wait more than 10 seconds, switch the light back on to resume “Party Mode.” Selecting a GloBrite Light Color and Show Modes or Fixed ® Color Using an IntelliBrite...
Page 8: Globrite Color Light Fixture Installation (New Pool Construction)
There are three types of GloBrite Color Light niches for pool or spa: Concrete/gunite, fiberglass or vinyl liner. Note: The GloBrite color light niche must be installed in or on the wall of the pool (or water feature) with the top of the lens not less than 4 inches (10.2 cm) below the normal water level of the pool.
Page 9: Option 1: Light Niche Sleeve With Cone
11. After the plastering has been completed, remove and dispose of the gunite cover. 2” PVC pipe Schedule 40 (Niche Sleeve) 15” MIN. Cone Gunite niche 1” Conduit glue to reducer Option 1: Niche Sleeve with Cone - Installation Diagram GLOBRITE™ Color Changing LED Pool/Spa Light Installation and User’s Guide...
Page 10: Option 2: Conduit To Light Niche
2” PVC pipe Schedule 40 Color Ring (Niche Sleeve) 15” MIN. Gunite niche 1” Conduit glue Gunite Cover to Gunite Niche Option 2: Conduit to Light - Installation Diagram GLOBRITE™ Color Changing LED Pool /Spa Light Installation and User’s Guide...
Page 11: Installing Globrite Color Light In A Fiberglass Pool
™ To install the GloBrite color light niche in a fiberglass pool: Drill or punch a 2-1/8 inch hole in the desired location for the GloBrite light niche. Place the sealing gasket on the niche as shown below. Insert the niche through the 2-1/8 inch hole in the pool wall.
Page 12: Installing Globrite Color Light In A Vinyl Pool
Installing GloBrite™ Color Light Niche in a Vinyl Pool To install the GloBrite color light niche in a vinyl liner pool: Drill a 3 inch hole in the desired location for the light vinyl niche. From the inside of the pool, insert the vinyl niche through the 3” hole.
Page 13: Installing The Globrite Color Light Assembly (After Niche Installation)
To install the GloBrite color light into the gunite, fiberglass or vinyl niche: Route the GloBrite light power cord through the front of the niche, to the location of the 12 VAC pool transformer or junction box. At the 12 VAC transformer or junction box, cut off any extra cord. Leave at least six (6) inches (15.2 cm) of cord in the Junction Box or...
Page 14 ™ GloBrite Color Light Installation/Removal Tool Before operating the GloBrite color light, fill the pool with water until the light is completely submerged. Note: The GloBrite color light should not be powered for more than 30 seconds if is not submersed in water.
Page 15: Replacing The Globrite Color Light Assembly (In An Existing Pool Or Spa)
GloBrite light’s lens is at least 4 inches below (not more than 48 inches below in Canada) the surface of the water in the pool or spa.
Page 16: Replacing The Globrite Color Light Assembly (After Electrical Requirements Are Met)
Remove the GloBrite color light assembly from the pool or spa water: Using the provided installation tool (P/N 620057), rotate the light assembly counter-clockwise about a 1/8th turn to release the light from the niche as shown on page 10).
Page 17: Connecting Globrite Color Lights To Easytouch/Intellitouch Load Center
Loosen the two (2) retaining screws from the HIGH VOLTAGE FRONT PANEL. Remove the panel from the enclosure. Run the GloBrite color light power cord to a auxiliary relay in the EasyTouch/IntelliTouch load center. Connect the 120 Volt side of a 12 VAC transformer to the LOAD SIDE of one of the auxiliary (AUX) relays in the load center.
Page 18 Lights require a 100 Watt load maximum) transformer. ® ® EasyTouch and IntelliTouch Control System Load Center Wiring Diagram ™ GloBrite Color Light with Wall Switch Wiring Diagram GLOBRITE™ Color Changing LED Pool /Spa Light Installation and User’s Guide...
Page 19: Setting Up Globrite Color Lights With Easytouch/Intellitouch Control System
From the EasyTouch control panel you can control the light shows. To set up a GloBrite light circuit; assign the “Light Circuit Name” to the relay circuit (example; AUX 3, as “Pool Light”) and “Function”: assign the name “Pool Light” circuit in the Circuit Func.
Page 20 Wireless Remote control panel. Assigning a Circuit Name To identify the GloBrite light connected to the auxiliary circuits (AUX 1, AUX 2) in the IntelliTouch load center, you need to assign the GloBrite light circuit name to the corresponding auxiliary circuits in the IntelliTouch indoor control panel. Choose a circuit name from the preset list of names for the GloBrite light connected to the auxiliary relay installed in the IntelliTouch load center.
Page 21 Each GloBrite light must also be assigned a circuit function. To assign a Circuit Name for the GloBrite light, go to: MENU > SETUP > ADVANCED > CIRCUIT FUNCTIONS Setup a GloBrite light function circuit: Assign each light auxiliary relay circuit a circuit name, then assign that light relay circuit in the “CIRCUIT FUNCTIONS”...
Page 22: Wiring Globrite Color Lights To Intellibrite Controller And 300 W Transformer
Color Lights to IntelliBrite Controller and ™ 300 Watt Transformer ™ The following diagram shows how to connect GloBrite color light to an IntelliBrite Controller using a 300 Watt transformer. Note: For GloBrite light operating instructions, see page 3. 300 Watt wire nut Transformer GREEN...
Page 23: Globrite Color Lights Parts List And Replacement Kits
Fiberglass combo #2 - 2 GloBrite 100' w/300W txfmr & 2 Fiberglass niches 620080 Vinyl combo #1- 1 GloBrite 100' w/300W txfmr and vinyl niche 620081 Vinyl combo #2 - 2 GloBrite 100' w/300W txfmr and two vinyl niches ™ GloBrite Light Niches Part No.
Page 24 1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000 10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000 WWW.PENTAIRPOOL.COM All Pentair trademarks and logos are owned by Pentair, Inc. Pentair Aquatic Systems™, GloBrite™, ® ® ® ® ®...

Pentair GLOBRITE Installation And User Manual

Quick Links

Related Manuals for Pentair GLOBRITE

Summary of Contents for Pentair GLOBRITE

Table of Contents