Color changing underwater led light for pool and spa (24 pages)
Summary of Contents for Pentair Globrite
Page 1
™ GLOBRITE WHITE LED LIGHT FOR POOL AND SPA INSTALLATION USER’S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS GLOBRITE™ White LED Pool/Spa Light Installation and User’s Guide...
Installing the GloBrite Light Sleeve and Niche (after electrical requirements are met) ..............3 Installing the GloBrite Light Sleeve and Niche in a Concrete/Gunite Pool ... 4 Option 1: Light Niche Sleeve with Cone ............4 Option 2: Conduit to Light Niche ..............5 Installing GloBrite Light in a Fiberglass Pool ............
THE GLOBRITE™ UNDERWATER LED POOL LIGHT REQUIRES HIGH VOLTAGE WHICH CAN SHOCK, BURN, OR CAUSE DEATH. BEFORE WORKING ON the GloBrite LED Light always disconnect power to the pool and/or spa lights at the source circuit breaker from the light before servicing the light. Failure to do so could result in death or serious injury to service person, pool users or others due to electric shock.
Page 4
COMPLIANCE WITH THE CURRENT NATIONAL ELECTRIC CODE (NEC). UNBONDED LIGHTING NEC PROVISIONS: When the UL listed non-metallic GloBrite LED Light low voltage lights are used with the GloBrite light approved niches (as listed on page 19), the current NEC provides an exception to luminaire bonding and grounding in Article 680.6 and 680.23...
This manual describes how to install and replace the pool and spa GloBrite White LED Light. The GloBrite White LED Light allows you to choose from one of three brightness levels. For more information see page 2. Operating GloBrite LED Lights Using a Wall Switch The GloBrite LED light can be manually controlled using a standard wall-mount light switch.
White Lights can be controlled using a standard wall-mount light switch. Multiple GloBrite white lights can be connected via a junction box and a 12 VAC transformer to a single switch so that all lights can be switched on and off together. GloBrite White lights are controlled by cycling AC power to the 12 VAC transformer from a standard wall switch.
There are three types of GloBrite LED Light niches for pool or spa: Concrete/gunite, fiberglass or vinyl liner. Note: The GloBrite light niche must be installed in or on the wall of the pool (or water feature) with the top of the lens not less than 4 inches (10.2 cm) below the normal water level of the pool.
11. After the plastering has been completed, remove and dispose of the gunite cover. 2” PVC pipe Schedule 40 (Niche Sleeve) 15” MIN. Cone Gunite niche 1” Conduit glue to reducer Option 1: Niche Sleeve with Cone - Installation Diagram GLOBRITE™ White LED Pool /Spa Light Installation and User’s Guide...
11. After the plastering has been completed, remove and dispose of the gunite cover. 2” PVC pipe Schedule 40 Color Ring (Niche Sleeve) 15” MIN. Gunite niche 1” Conduit glue Gunite Cover to Gunite Niche Option 2: Conduit to Light - Installation Diagram GLOBRITE™ White LED Pool/Spa Light Installation and User’s Guide...
™ To install the GloBrite light niche in a fiberglass pool: Drill or punch a 2-1/8 inch hole in the desired location for the GloBrite light niche. Place the sealing gasket on the niche as shown below. Insert the niche through the 2-1/8 inch hole in the pool wall.
Installing GloBrite™ Light Niche in a Vinyl Pool To install the GloBrite light niche in a vinyl liner pool: Drill a 3 inch hole in the desired location for the light vinyl niche. From the inside of the pool, insert the vinyl niche through the 3” hole.
To install the GloBrite light into the gunite, fiberglass or vinyl niche: Route the GloBrite light power cord through the front of the niche, to the location of the 12 VAC pool transformer or junction box. At the 12 VAC transformer or junction box, cut off any extra cord. Leave at least six (6) inches (15.2 cm) of cord in the Junction Box or...
Page 13
™ GloBrite LED Light Installation/Removal Tool Before operating the GloBrite light, fill the pool with water until the light is completely submerged. Note: The GloBrite light should not be powered for more than 30 seconds if is not submersed in water.
The GloBrite light niche must be properly installed so that the top edge of the lens of the GloBrite light is at least 4 inches below (not more than 48 inches below in Canada) the surface of the water in the pool or spa.
Remove the GloBrite light assembly from the pool or spa water: Using the provided installation tool (P/N 620057), rotate the light assembly counter-clockwise about a 1/8th turn to release the light from the niche as shown on page 9).
Loosen the two (2) retaining screws from the HIGH VOLTAGE FRONT PANEL. Remove the panel from the enclosure. Run the GloBrite light power cord to a auxiliary relay in the EasyTouch/ IntelliTouch load center. Connect the 120 Volt side of a 12 VAC transformer to the LOAD SIDE of one of the auxiliary (AUX) relays in the load center.
Page 17
Five GloBrite 12 VAC transformer Lights require a 100 Watt load maximum) transformer. ® ® EasyTouch and IntelliTouch Control System Load Center Wiring Diagram Five ™ GloBrite LED Light with Wall Switch Wiring Diagram GLOBRITE™ White LED Pool/Spa Light Installation and User’s Guide...
Page 19
Notes GLOBRITE™ White LED Pool/Spa Light Installation and User’s Guide...
Page 20
1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000 10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000 WWW.PENTAIRPOOL.COM All Pentair trademarks and logos are owned by Pentair or by one of its global affiliates. Pentair Aquatic Systems™, GloBrite™, IntelliFlo , IntelliBrite...