Table of Contents
Advertisement
Initial installation
Explanations of the setting possibilities:
Location
Select the country for country-specific pre-settings.
of TV set
If UK or IRL is selected for the location of TV set, it is pos-
sible to activate MHEG-5 (UK Freeview) for the TV set.
A dialogue appears, where you can confirm to set the
operating software to the selected location.
If Yes is selected and confirmed with OK, the TV set turns
off and on again automatically. First installation starts
again after activating the operation software.
If MHEG-5 was activated, DVB-C and DVB-S can not be
used anymore. Only terrestrial/cable and DVB-T stations
are available.
Antenna
Antenna/cable (analogue): analogue stations via
selection
DVB-T:
DVB-C:
DVB-S (cable 1):
DVB-S (cable 2):
Encrypted
You can state whether coded stations are to be searched
stations
for in the search/update. Select yes then coded stations
are also searched for. However, these stations can only
be received in connection with a CA module and the
appropriate Smart Card. Handling of the CA module is
described on page 35.
DVB-T:
If you are using an active antenna, then select yes (5V)
Antenna
for the antenna power supply.
DVB-C:
The conventional settings will be derived from the selection
Settings
of set location. Only change this if you know other symbol
rates and modulation types or if you have to specify the
network ID for your cable network (information available
from your cable network provider). If you want to run the
station search independently of the channel grid, select
frequency search for the search method.
DVB-S:
Select which satellite(s) you receive from a list. For more
Satellite
than one satellite, select the type of your changeover
system
switch or communal satellite system additionally.
Ask your dealer in this regard.
High band
Specify here whether the high band of the selected satellite
is to be searched in addition to the low band.
- 12
cable/antenna
digital terrestrial stations
digital stations via cable
digital stations via satellite
digital stations via satellite
LNC
Normally, you do not need to change the values for high
frequencies
and low band, unless the LNC (LNB) of your satellite
Low Band /
system uses a different oscillator frequency (important
High Band
for the frequency display).
After you have made these settings, you should receive
the picture and sound of the selected satellites (only with
Astra1 and HOTBIRD).
Search
If you want to run the station search independently of
method
the channel grid, select frequency search for the search
method.
Symbol rates
The symbol rates are specified by the satellite provider
and normally do not need to be changed.
Favoured
Select the signal source that provides the stations to be on
signal source
top of your station list (starting with station slot 1).
Start search
Start the automatic station search with OK.
First TV stations, then radio stations are searched for.
The stations found in the automatic search are divided
into the appropriate station blocks depending on the
previously selected antenna cables (signal sources). Sub-
sequently the stations can only be re-sorted within these
blocks. At the beginning of the station list you will find the
block with the stations of the preferred signal source.
Any mixed sorting of stations from different signal sources
is only possible with the favourites list.
➠ For TV sets with MHEG-5 software the stations are
tied to "Logical Channel Numbers" – "LCN" and
sorted from 1-799. Digital stations without "LCN" are
stored from 800 onwards. Analogue stations are stored
from 1001.
Connecting
Then the connection and sound component wizard
additional
starts which helps you to log in, set and connect video
devices
recorders, decoders, a loudspeaker system or a HiFi/AV
amplifier to your TV set. DVD players and DVD recorders
are already registered at the factory.
You can start the connection wizard and the sound
components wizard manually later and add new devices.
Further information is available from page 40 (Connection
wizard) and page 47 (Sound components wizard).
Ž
continued on next page
Hide quick links:
Advertisement
Table of Contents
