Sony CDX-F7000 Service Manual
Fm/am compact disc player
Hide thumbs
Also See for CDX-F7000:
- Operating instructions manual (60 pages) ,
- Installation/connections (5 pages) ,
- Operating & installation instructions (2 pages)
Table of Contents
Advertisement
Quick Links
CDX-F7000/F7005X/FW700
SERVICE MANUAL
Ver 1.0 2003. 12
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
Sony Corporation
9-961-473-01
2003L04-1
e Vehicle Company
© 2003. 12
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
General
Outputs
Inputs
Tone controls
Loudness
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Design and specifications are subject to change without
notice.
FM/AM COMPACT DISC PLAYER
US Model
CDX-F7000/F7005X/FW700
Canadian Model
CDX-F7000/F7005X
CDX-S2000/SW200
MG-611XA-186//K
KSS1000E
Audio output terminals (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input or AUX IN terminal
Remote controller input terminal
Antenna input terminal
Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
+8 dB at 100 Hz
+2 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 178 mm
× 2 × 7
(7
in.) (w/h/d)
1/8
1/8
Approx. 182 × 53 × 161 mm
× 2
× 6
(7
in.) (w/h/d)
1/4
1/8
3/8
Approx. 1.3 kg (2 lb. 14 oz.)
Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X118A
1
Advertisement
Chapters
Table of Contents
Related Manuals for Sony CDX-F7000
Summary of Contents for Sony CDX-F7000
- Page 1 Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) FM/AM COMPACT DISC PLAYER Sony Corporation 9-961-473-01 2003L04-1 e Vehicle Company © 2003. 12 Published by Sony Engineering Corporation...
- Page 2 CD player. DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
- Page 3 CDX-F7000/F7005X/FW700 UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics.
-
Page 4: Table Of Contents
CDX-F7000/F7005X/FW700 TABLE OF CONTENTS 1. GENERAL Location of Controls ..............5 Connections (CDX-F7000/F7005X) ........6 Connections (CDX-FW700) ............ 7 2. DISASSEMBLY 2-1. Sub Panel Assy (CD) ............9 2-2. CD Mechanism Block ............9 2-3. Main Board ............... 10 2-4. Chassis (T) Sub Assy ............10 2-5. -
Page 5: General
To store stations/receive stored stations. device is connected to AUX IN terminal of the unit. albums, press (and hold) CD/MD: When you connect a Sony portable device and CD/ within about 1 second of (1): REP 13 MODE MD unit(s) at the same time, use the AUX IN first releasing the button. -
Page 6: Connections (Cdx-F7000/F7005X)
CDX-F7000/F7005X/FW700 Connections (CDX-F7000/F7005X) Source selector (not supplied) Sélecteur de source Supplied with the CD/MD changer (non fourni) Fourni avec le changeur de CD/MD XA-C30 BUS AUDIO IN /AUX IN AUDIO OUT REMOTE FRONT RCA pin cord (not supplied) Be sure to match the color-coded cord for audio to the appropriate jacks from the unit. -
Page 7: Connections (Cdx-Fw700)
CDX-F7000/F7005X/FW700 Connections (CDX-FW700) Source selector (not supplied) Supplied with the CD/MD changer Selector de fuente Suministrado con el cambiador de CD/MD (no suministrado) XA-C30 BUS AUDIO IN /AUX IN AUDIO OUT REMOTE FRONT RCA pin cord (not supplied) Be sure to match the color-coded... -
Page 8: Disassembly
CDX-F7000/F7005X/FW700 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-1. SUB PANEL ASSY (CD) (Page 9) 2-2. CD MECHANISM BLOCK (Page 9) 2-10. SERVO BOARD 2-3. MAIN BOARD 2-4. CHASSIS (T) SUB ASSY... -
Page 9: Sub Panel Assy (Cd)
CDX-F7000/F7005X/FW700 Note : Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL ASSY (CD) 3 two claws 2 two claws CN601 1 two screws (+PTT 2.6 x 6) 5 sub panel assy (CD) 2-2. CD MECHANISM BLOCK... -
Page 10: Main Board
CDX-F7000/F7005X/FW700 2-3. MAIN BOARD 6 cord 2 two screws (+PTT 2.6 x 8) 1 three ground point screws (+PTT 2.6 x 6) 5 two screws (+PTT 2.6 x 8) 4 CN401 3 MAIN board 2-4. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 x 2.2) -
Page 11: Roller Arm Assy
CDX-F7000/F7005X/FW700 2-5. ROLLER ARM ASSY 3 washer (1.1 – 2.5) 5 roller arm assy 4 worm wheel (RA) 2 spring (RAR) 1 spring (RAL) 2-6. CHASSIS (OP) ASSY qa chassis (OP) assy 0 compression spring (damper) lever (D) 4 washer... -
Page 12: Optical Pick-Up
CDX-F7000/F7005X/FW700 2-7. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 x 5) 2-8. SL MOTOR ASSY (M902) 1 screw (+P 1.4 x 1.8) -
Page 13: Le Motor Assy (M903)
CDX-F7000/F7005X/FW700 2-9. LE MOTOR ASSY (M903) 8 screw 0 woam (LEB) assy (+M 1.7 x 2.5) 9 bearing (LEB) 2 washer qa screw (+M 1.7 x 2.5) qf two toothed lock screws 3 gear (LE1) (+M 1.4 ) lever (D) -
Page 14: Diagrams
CDX-F7000/F7005X/FW700 SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTIONS • IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON) Dimmer monitor input from optical pick-up laser diode. - Page 15 CDX-F7000/F7005X/FW700 Pin No. Pin Name Pin Description LRCK Not used. (Connect to LRCKIN in this set) DVDD — Power supply pin (+3.3 V) Focus servo drive PWM signal output (+) FD– Focus servo drive PWM signal output (–) Tracking servo drive PWM signal output (+) TD–...
- Page 16 Electronic volume mute signal output I2C CKO I2C bus serial clock output I2C SIO I2C bus serial data output UNI SO SONY bus serial data output UNI SI SONY bus serial data input UNI CKO SONY bus serial clock output TUNER ATT...
- Page 17 CDX-F7000/F7005X/FW700 Pin No. Pin Name Pin Description CD LM EJECT CD eject signal output CD RESET CD reset signal output CD AO CD AO signal output CD STB CD strobe signal output (NCO) Not used CD RF OK CD RF OK signal input...
- Page 18 CDX-F7000/F7005X/FW700 • IC901 M30823MH-080GP (DISPLAY CONTROL) (KEY BOARD) Pin No. Pin Name Pin Description SYS CE Main chip enable input (NCO) Not used FL DAT3 FL serial data output 3 (NCO) Not used FL CLK IN FL serial clock input BYTE Connecting to ground.
-
Page 19: Block Diagram -Cd Section
CDX-F7000/F7005X/FW700 3-2. BLOCK DIAGRAM — CD SECTION — RF AMP,DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR OPTICAL PICK-UP (KSS1000E) (Page 20) TUNER SECTION LOUT ROUT DEMOD CONV R-CH SYSTEM CONTROL IC303 (1/3) INTQ CONV. 16 CD_INTQ CD_SO IC251 (1/3) 6 CD_SI FORCUS... -
Page 20: Block Diagram -Main Section
CDX-F7000/F7005X/FW700 3-3. BLOCK DIAGRAM — MAIN SECTION — CN401 SUB OUT(MONO) MUTE ELECTRONIC VOLUME Q470 GROUND SW IC401 Q408 PB LCH PB RCH R-CH AUDIO IN R-CH OUTSW (Page 19) CD-L 42 CD LCH SECTION R-CH 43 CD RCH REAR... -
Page 21: Block Diagram -Display Section
CDX-F7000/F7005X/FW700 3-4. BLOCK DIAGRAM — DISPLAY SECTION — SYSTEM CONTROL DISPLAY CONTROL IC303 (3/3) IC901 FL DAT1 ROTARY REIN0 ENCODER FL DAT2 DISP CE 1 CE ENC901(1/2) REIN1 FL DAT3 DISP SI DISP SO KEY MATRIX DISP CKO KEYIN0 FL CLK... -
Page 22: Note For Printed Wiring Boards And Schematic Diagrams
CDX-F7000/F7005X/FW700 3-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 3-6. WAVEFORMS THIS NOTE IS COMMON FOR PRINTED WIRING — Servo Board — BOARDS AND SCHEMATIC DIAGRAMS. — Main Board — (MODE: CD PLAY) (In addition to this, the necessary note is printed in each block.) -
Page 23: Printed Wiring Boards -Cd Mechanism Section
CDX-F7000/F7005X/FW700 3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. CNP301 (Page 29) -
Page 24: Schematic Diagram -Cd Mechanism Section
CDX-F7000/F7005X/FW700 • Refer to page 22 for Waveforms. 3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 34 for IC Block Diagram. TP19 TP32 TP33 R14 R15 TP31 TP20 TP30 TP29 TP14 TP21 TP28 TP27 TP26 TP13... -
Page 25: Schematic Diagram -Main Section (1/3)
CDX-F7000/F7005X/FW700 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 34 for IC Block Diagram. TUX501 FB442 C442 CN401 C508 R478 R402 C443 FB441 R407 Q470 L503 C509 C507 J601 C510 C278 R274 C273 C178 R272 R429... -
Page 26: Schematic Diagram -Main Section (2/3)
CDX-F7000/F7005X/FW700 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 34 for IC Block Diagram. C215 C210 C205 IC B/D D111 D110 CNP101 D113 C206 R203 D112 C218 R205 CN103 CN102 C208 C216 D114 C209 C217 IC201... -
Page 27: Schematic Diagram -Main Section (3/3)
CDX-F7000/F7005X/FW700 • Refer to page 22 for Waveforms. 3-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 35 for IC Block Diagram. (Page 25) (Page 26) (Page 24) CNP301 FB329 C336 FB325 L303 R904 FB326 C335 C342... -
Page 28: Printed Wiring Boards -Main Section
CDX-F7000/F7005X/FW700 3-13. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location D101 D104 D105 D106 D111 Q271 Q171 Q281 Q181 Q470 C208 C209... - Page 29 CDX-F7000/F7005X/FW700 PJ401 CNJ101 J601 CNP102 D122 C199 D110 CNP101 C242 C211 F901 C210 C205 C288 C215 D112 IC201 R410 R242 R175 R274 R185 CN103 D102 R142 D103 R143 R243 R184 R284 R174 R275 CN102 D117 C101 D121 D116 C225 D120...
-
Page 30: Printed Wiring Board -Sub Section
CDX-F7000/F7005X/FW700 3-14. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. (Page 32) D991 CNP501 LED932 R991 R990 LED931 D990 S901 (Page 29) -
Page 31: Schematic Diagram -Sub Section
CDX-F7000/F7005X/FW700 3-15. SCHEMATIC DIAGRAM — SUB SECTION — CNP501 (Page 33) (Page 26) R990 D991 D990 S901 R991 LED932 LED931... -
Page 32: Printed Wiring Board -Key Section
H-13 IC902 LED913 LED921 D903 (D915) IC903 B-14 LED914 LED922 D904 (D916) IC904 G-11 LED915 LED923 A-13 D909 G-12 (D917) LED916 LED924 D910 G-12 (D918) LED901 C-14 LED917 D911 H-14 (D919) LED910 LED918 D912 G-10 LED911 LED919 ): CDX-F7000/FW700 only... -
Page 33: Schematic Diagram -Key Section
CDX-F7000/F7005X/FW700 3-17. SCHEMATIC DIAGRAM — KEY SECTION — ENC901(1/2) CN901 R979 R980 R981 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R983 R984 R985 C901 LED923 LED901 LED924 LSW903(2/2) LSW905(2/2) LSW907(2/2) LSW901(2/2) LED910 D901 LSW904(2/2) LSW908(2/2) LSW902(2/2) LSW906(2/2) -
Page 34: Ic Block Diagrams
CDX-F7000/F7005X/FW700 3-18. IC BLOCK DIAGRAMS IC401 TDA7416 (MAIN Board (1/3)) IC2 BA5966FP-FE2 (SERVO Board) 30 29 24 23 HIGH PASS MIXER FILTER2 SOFT STEP FADER MUTE – – – – ACOUT-R SOFT STEP ACIN-SW FADER ACOUT-SW – HIGH PASS –... - Page 35 CDX-F7000/F7005X/FW700 IC201 TDA8588AJ/N2 (MAIN Board (2/3)) OUT FL- I2C BUS OUT FL+ OUT RL- PGND3 OUT RL+ INRL INFL SGND PROTECTION DIAGNOSTIC INFR INRR AC GND OUT RR+ PGND2 OUT RR- OUT FR+ STANDBY MUTE OUT FR- CHIP DETECT DIAGNOSTIC...
-
Page 36: Exploded Views
CDX-F7000/F7005X/FW700 SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety. -
Page 37: Front Panel Section
CDX-F7000/F7005X/FW700 4-2. FRONT PANEL SECTION FL900 not supplied (KEY board) not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3384-492-1 BUTTON KIT ASSY (S) X-3384-495-1 PANEL ASSY, FRONT BACK 3-032-321-01 SPRING (OPEN) -
Page 38: Cd Mechanism Section (1)
CDX-F7000/F7005X/FW700 4-3. CD MECHANISM SECTION (1) (MG-611XA-186//K) not supplied not supplied (SENSOR board) not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-455-A CHASSIS (T) SUB ASSY 3-253-748-01 DAMPER (S) 3-253-729-01 SPRING (LTR), TENSION COIL 3-352-758-31 SCREW (M1.7), TOOTHED LOCK... -
Page 39: Cd Mechanism Section (2)
CDX-F7000/F7005X/FW700 4-4. CD MECHANISM SECTION (2) (MG-611XA-186//K) (including M901) M902 not supplied not supplied not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. -
Page 40: Cd Mechanism Section (3)
CDX-F7000/F7005X/FW700 4-5. CD MECHANISM SECTION (3) (MG-611XA-186//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-262-755-01 WASHER (1.1-2.5) 3-259-467-01 BRACKET (LEM) 3-259-024-01 WHEEL (RA), WORM 3-345-648-91 SCREW (M1.4), TOOTHED LOCK A-3337-633-A ARM ASSY, ROLLER A-3372-456-A WORM (LEB) ASSY... -
Page 41: Cd Mechanism Section (4)
CDX-F7000/F7005X/FW700 4-6. CD MECHANISM SECTION (4) (MG-611XA-186//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-259-429-01 WHEEL (LE), WORM 3-899-829-01 WASHER (SLIT) 3-344-223-01 WASHER 3-259-032-01 GEAR (LE2) 3-259-470-01 GEAR (LE1) A-3372-453-A CHASSIS (M) BLOCK ASSY 3-253-755-01 LEVER (D) -
Page 42: Electrical Parts List
CDX-F7000/F7005X/FW700 SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service. - Page 43 CDX-F7000/F7005X/FW700 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LED913 6-500-204-01 LED CL-190UB2-X-T (SEEK +/>/M) LSW908 1-786-711-31 SWITCH, TACTILE (WITH LED) (1/REP) (F7005X) (F7005X) LED913 6-500-450-01 LED CL-195SR-CD-T (SEEK +/>/M) (F7000/FW700) < RESISTOR > LED914 6-500-204-01 LED CL-190UB2-X-T (DISC/PRESET +)
-
Page 44: Ref. No
CDX-F7000/F7005X/FW700 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R931 1-216-820-11 METAL CHIP 1/10W R985 1-216-823-11 METAL CHIP 1.5K 1/10W (F7000/FW700) (F7000/FW700) R932 1-216-811-11 METAL CHIP 1/10W R987 1-216-845-11 METAL CHIP 100K 1/10W (F7005X) R932... -
Page 45: Ref. No
CDX-F7000/F7005X/FW700 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C242 1-162-927-11 CERAMIC CHIP 100PF C508 1-125-837-11 CERAMIC CHIP 6.3V C273 1-124-721-85 ELECT 10uF C509 1-125-837-11 CERAMIC CHIP 6.3V C278 1-162-927-11 CERAMIC CHIP 100PF C510 1-135-834-11 CERAMIC CHIP 2.2uF... -
Page 46: Description Remark
CDX-F7000/F7005X/FW700 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D403 8-719-069-55 DIODE UDZS-TE17-5.6B L502 1-414-394-41 INDUCTOR 2.2uH D501 8-719-069-55 DIODE UDZS-TE17-5.6B L503 1-414-394-41 INDUCTOR 2.2uH D601 8-719-978-33 DIODE DTZ-TT11-6.8B L620 1-456-729-11 COIL, POWER D602 8-719-978-33 DIODE DTZ-TT11-6.8B... - Page 47 CDX-F7000/F7005X/FW700 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R182 1-216-295-11 SHORT CHIP R356 1-218-871-11 METAL CHIP 0.5% 1/10W R184 1-216-809-11 METAL CHIP 1/10W R357 1-218-871-11 METAL CHIP 0.5% 1/10W R185 1-216-841-11 METAL CHIP 1/10W...
- Page 48 CDX-F7000/F7005X/FW700 MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R631 1-216-833-11 METAL CHIP 1/10W 1-162-970-11 CERAMIC CHIP 0.01uF R632 1-216-841-11 METAL CHIP 1/10W 1-107-826-11 CERAMIC CHIP 0.1uF R633 1-216-809-11 METAL CHIP 1/10W 1-107-826-11 CERAMIC CHIP 0.1uF...
- Page 49 CDX-F7000/F7005X/FW700 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-833-11 METAL CHIP 1/10W MISCELLANEOUS 1-216-797-11 METAL CHIP 1/10W *************** 1-216-797-11 METAL CHIP 1/10W 1-216-821-11 METAL CHIP 1/10W 1-776-207-72 CORD (WITH CONNECTOR) (POWER) 1-216-821-11 METAL CHIP...
- Page 50 CDX-F7000/F7005X/FW700 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003. 12...