Related Manuals for Prem-I-Air EH0530
Summary of Contents for Prem-I-Air EH0530
- Page 1 8000BTU WALL MOUNTED AIR CONDTIONER COOLING & HEATING Model EH0530 (PMINISW8W) (Refrigeration R407C) PLEASE READ THIS INSTRUCTION MANUAL BEFORE OPERATING AND KEEP SAFE FOR FUTURE REFERENCE...
-
Page 2: Table Of Contents
CONTENT Title Page A. Specification B. Before use C. Important safety instructions 5, 6 D. BS plug wiring / Schuko to UK converter plug (Optional) E. Product description 8, 9 F. Wall mounting installation instructions 9-13 G. Operating instructions 14-17 H. -
Page 3: Specification
A. SPECIFICATION Model EH0530 (PMINISW8W) Capacity(W) Cooling Capacity 2300 Heating Capacity 2400 Power (W) Cooling Heating Dehumidifying Capacity (L/day) Air Volume (m Power Supply 220-240V ~ /50Hz Noise Level (dB) <50 Refrigerant (g) R407C / 400g Net Weight(KG) (not includes accessories) -
Page 4: Before Use
B. BEFORE USE Transport & store the unit in an upright position only. Leave it in an upright position for at least 3 hours before first use. DO NOT dispose of any packaging until the installation of the air conditioner is completed. After having removed the packing, check that all the content is intact and complete. -
Page 5: Important Safety Instructions
C. IMPORTANT SAFETY INSTRUCTIONS Always place the unit on an even, level surface. An opening in a window (in portable version only) or wall is required to accommodate the exhaust hose to expel the hot air. Ensure the unit is connected to an earthed power supply of the correct rating. - Page 6 Energy Saving Tips Blocking of the filter reduces the efficiency of the air and increases its power consumption by up to 6%. Avoid opening doors frequently. Each person present in a room provides between 100 Watts and 150 Watts of heat. Consequently, the more people there are in a room, the less effective the unit will be in cooling.
-
Page 7: Bs Plug Wiring / Schuko To Uk Converter Plug (Optional)
D. BS PLUG WIRING Wiring Instructions: Should it be necessary to change the plug please note the wires in the mains lead are colored in accordance with the following code: BLUE - NEUTRAL BROWN - LIVE GREEN AND YELLOW - EARTH As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows:... -
Page 8: Product Description
E. PRODUCT DESCRIPTION Air outlet Wire control connection (optional) LED display Caster bracket locking holes (using in mobile version only) Remote control storage Caster bracket hanging hole (using in mobile version only) Control panel Air exhaust Handles Air inlet Dust filter Drainage hole Hanging holes (for wall mount Caster bracket hanging hole... -
Page 9: Wall Mounting Installation Instructions
Wall mounted kit: Wall bracket x 1pc Pipe flange x 2pcs Air intake pipe (dia.120mm) x 1pc External grating (Pre-installed) x 2pcs Hot air discharge pipe (dia.130mm) x 1pc Template for wall drilling x 1pc Extension condensate hose x 1pc Screw kit: ST4*10 x 10pcs ST5*40 x 8pcs Nylon anchor ∅5*40 x 8pcs... - Page 10 2. Template Fasten the template to the wall once the following guidelines have been thoroughly checked. Do not drill any holes until you are 100% confident that there are no obstacles in the area you wish to drill and there are no obstructions, which could be hidden by the construction of the wall, for example: Electrical wiring, water &...
- Page 11 3. Drilling the Wall Please note: If you are drilling the hole above ground floor level, please ensure that the outside area is supervised until drilling has been completed. 1) INTAKE AND OUTLET HOLES This operation should be carried out using the proper tools (diamond tip or core bit drills with high twisting torque and adjustable rotation speed)
- Page 12 4. Installation of vent tubes After drilling the holes, the rubber rings, the plastic pipes and the grids supplied with the air conditioner need to be fitted through them. The pipe with a diameter 130mm (hot air discharge) has to be fitted in the right hole.
- Page 13 IMPORTANT SUGGESTIONS: Because the hot air discharge pipe diameter is nearly the same as the 135mm drill bit, the pipe is slightly tight fit into wall hole. If you experience any difficulties, use a small piece of timber & a rubber hammer to gently knock the tube into the hole. After the pipe has been installed through the wall, insulate and seal its perimeter to prevent air and humidity infiltration using polyurethane foam.
-
Page 14: Operating Instructions
G. OPERATION INSTRUCTIONS CONTROL PANEL Green light switched on: compressor is ON Yellow light switched on: timer is on Red light switched on: the unit is in standby Blue light switched on: night mode is on shows room temperature when unit is running and shows corresponding setting when you press the control key. - Page 15 TIMER Press “TIMER” button until the Yellow light is on to set Automatic Off time while the unit is running. Press “Timer” button until the Yellow light is on to set Automatic On time while the unit is in ready state. Press either “UP”...
- Page 16 3) Fan Operation Plug the Power Cord into the power outlet socket. Turn on the unit by pressing the ON/OFF Button on the control panel. Press the MODE Button until “ ” appears on the LED display. Select the fan speed by pressing the FAN Button. 4) Heating Operation Plug the Power Cord into the power outlet socket.
- Page 17 6) Sleep Mode (This Mode is available when using Remote control) The air conditioner is in operation Press SLEEP Button, the “ ” appears on the Remote control display. The unit will switch to low speed after 2 hours. When in cooling mode, during the first two hours, the temperature will be increased 1 C per hour.
-
Page 18: Operation Using Remote Controller
H. OPERATION USING REMOTE CONTROLLER (Type V5) 1. Remove the cover from the back of the remote control. 2. Insert two AAA dry-cell batteries (batteries included). After inserting the batteries, the display of the remote control will flash COOL and HEAT orderly : to set the remote control of your unit, you can press the MODE button when the remote is flashing HEAT on the... - Page 19 5. Clock Time settings: HR and MIN To set the hours, press HR button once, the time will add 1 hour, continue to press this button, the clock will add by 1 hour until extended 11 hours, then will change to PM or AM and return to 0(12:00). To set the minutes, press MIN button once, the clock will add 1 minute, continue to press this button and the clock will add by 1 minute until extended to 59 minutes, the return 00.
-
Page 20: Extra Air Flow
I. EXTRA AIR FLOW The extra airflow is positioned under the unit. It is placed in the closed position during manufacture for use in cooling mode. You are recommended to close it in wintertime to stop cool air from outdoors entering or in heating mode. Loosen the 2 buttery screws in both sides and put the door to wall direction. -
Page 21: Maintenance
K. MAINTENANCE Note: Make sure power is off and the plug is pulled out of the power outlet before performing any maintenance activities. WARNING: Shape fins behind the filter. DO NOT touch or hold the back of unit’s filter area if filter is removed for clean. Clean or replace filter If the air filter is blocked with dust, the airflow volume will reduce. -
Page 22: Trouble Shooting
L. TROUBLE SHOOTING Please check the following items before asking for repairing: PROBLEMS CAUSES SUGGEST SOLUTIONS The unit does not work Power supply fault: 1. Not plugged in; 1. Plug in correctly; 2. Faulty plug or socket; 2. Change the plug or socket; 3. -
Page 23: Service & Warranty
ONE (1) YEAR LIMITED WARRANTY Save This Warranty Information Prem-I-Air Appliances Ltd. Guarantees this product free from defects in materials and workmanship for a period of one (1) year. Should this unit be operated under conditions other than those recommended, at voltages other than the voltage indicated on the unit, or any attempts made to service or modify the unit, will render this WARRANTY VOID.