1. Manuals
  2. Brands
  3. Hyundai Manuals
  4. Drill
  5. HY2155
  6. User manual

Hyundai HY2155 User Manual

18v combi (hammer) drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
18V COMBI (HAMMER) DRILL
Model HY2155
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Hyundai HY2155

Summary of Contents for Hyundai HY2155

  • Page 1 18V COMBI (HAMMER) DRILL Model HY2155 User Manual...

  • Page 2: Table Of Contents

    CONTENTS o’s Section Description Page N 1. OWNER’S MANUAL & SAFETY INSTRUCTIONS 2. GENERAL SAFETY 3 – 5 3. BATTERY PACK 5 – 6 4. CHARGING 6 – 7 5. INSERTING/REMOVING BATTERY 7 – 8 6. QUICK REFERENCE 8 – 13 7.

  • Page 3: Owner's Manual & Safety Instructions

    1. OWNER’S MANUAL & SAFETY INSTRUCTIONS 1.1. How to read the manual. 1.1.1. Keep this manual for the safety warnings and precautions, assembly, operation, inspection, maintenance and cleaning procedures. 1.1.2. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
  • Page 4 2.2.4. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 2.2.5. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

  • Page 5: Battery Pack

    2.4.7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. 2.4.8. Use of the power tool for operations different from those intended could result in a hazardous situation.

  • Page 6: Charging

    3.1.3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 3.1.4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away.

  • Page 7: Inserting/Removing Battery

    4.9. After charging is complete, the GREEN LED on the charger will come ON and the RED light will go OFF, 4.10. The battery pack will fully charge if left on the charger, but it will not overcharge. Led Indicator Battery Pack Red Led Green Led...

  • Page 8: Quick Reference

    5.2.1. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions; 5.2.1.1. Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on the tool and stop the application that caused the tool to become overloaded.
  • Page 9 6.2. Installing or removing driver bit or drill bit 6.2.1. Turn the sleeve counter clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. 6.2.2. Turn the sleeve clockwise to tighten the chuck. To remove the bit, turn the sleeve counter clockwise.
  • Page 10 6.7.1. Pull the switch trigger to light up the lamp. 6.7.2. The lamp will stay ON whilst the switch trigger is being pulled. The lamp goes out 10 -15 seconds after releasing the trigger. 6.7.3. NOTE: Use a dry cloth to wipe the dirt off the lens of lamp. 6.7.4.
  • Page 11 6.10. Selecting mode. Always set the mode selection ring correctly to your desired mode mark. If you operate the tool with the ring positioned halfway between the mode marks, the tool may be damaged. 6.10.1. This tool employs an action mode changing ring. Select one of the three modes suitable for your work needs by using this ring.
  • Page 12 6.12.1. First, slide the action mode change lever so that it points to the marking. 6.12.2. The adjusting ring can be aligned in any torque levels for this operation. 6.12.3. Be sure to use a tungsten-carbide tipped bit. 6.12.4. Position the bit at the desired location for the hole, then pull the switch trigger. 6.12.5.

  • Page 13: Specification

    6.16. Drilling into metal 6.16.1. To prevent the bit from slipping when starting a hole, make an indentation with a centre- punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling.

  • Page 14: Genpower Contact Details

    Email contact; Technical service@genpower.co.uk 10.4. Web site; www.hyundaipowerequipment.co.uk 11. DECLARATIONS OF CONFORMITY 11.1. Genpower Ltd confirms that this Hyundai product conform to the following CE Directives; 11.1.1. 2006/42/EC Machinery Directive 11.1.2. 2004/108/EC EMC Directive 11.1.3. 2006/95/EC Low Voltage Directive Page 14...
  • Page 15 Page 15...
  • Page 16 Page 16...

Table of Contents